Nissan Juke F15. Manual — part 1212
TM-38
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
5. Remove transaxle case mounting bolts (
).
6. Remove reverse idler shaft mounting bolt (
) and seal washer.
7. Remove transaxle case (2) while rotating shifter lever A (1) in
the direction as shown in the figure.
8. Remove selector spring (1) from return bushing (A).
9. Shift 1st-2nd fork rod (1), fork rod (2), and reverse fork rod (3) to
the neutral position.
10. Remove selector (4) from clutch housing.
PCIB1694E
PCIB1695E
JPDIC0444ZZ
JPDIC0445ZZ
PCIB1698E
TRANSAXLE ASSEMBLY
TM-39
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
11. Remove reverse idler shaft assembly (1), as per the following
procedure.
a. Pull up input shaft assembly (2), mainshaft assembly (3), fork
rod (4), and 1st-2nd fork rod (5).
NOTE:
It is easier to pull up when shifting each fork rod to each shaft
side.
b. Remove reverse idler shaft assembly and reverse fork rod (6)
from clutch housing.
12. Remove spring washer from clutch housing.
13. Pull up and remove input shaft assembly (1), mainshaft assem-
bly (2), fork rod (3), and 1st-2nd fork rod (4) from clutch housing.
NOTE:
It is easier to pull up when shifting each fork rod to each shaft
side.
14. Remove final drive assembly (1) from clutch housing.
15. Remove magnet from clutch housing.
16. Remove differential side oil seals (1) from clutch housing and
transaxle case.
CAUTION:
Never damage clutch housing and transaxle case.
17. Remove differential side bearing outer race (1) from clutch hous-
ing, using a brass rod.
CAUTION:
Never damage clutch housing.
JPDIC0606ZZ
JPDIC0607ZZ
PCIB1703E
PCIB1704E
PCIB1716E
TM-40
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
18. Remove differential side bearing outer race (1) from transaxle
case, using a brass rod.
CAUTION:
Never damage transaxle case.
19. Remove shim (2) from transaxle case.
20. Remove shifter lever A (1) retaining pin, using a pin punch.
21. Remove shifter lever A from transaxle case.
22. Remove shifter lever B (1) from transaxle case.
23. Remove oil gutter (1) from transaxle case.
24. Remove bushings (1) from transaxle case, using a remover
[Commercial service tool].
PCIB1705E
JPDIC0106ZZ
PCIB1712E
PCIB1707E
PCIB1710E
TRANSAXLE ASSEMBLY
TM-41
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
25. Remove mainshaft rear bearing outer race from transaxle case,
using a remover [Commercial service tool].
26. Remove mainshaft rear bearing adjusting shim from transaxle
case.
27. Remove snap ring (1) and oil channel (2) from transaxle case.
28. Remove input shaft oil seal (1) from clutch housing, using an oil
seal remover.
CAUTION:
Never damage clutch housing.
29. Remove mainshaft front bearing outer race (1) from clutch hous-
ing, using the puller (A) [SST: KV381054S0 (J-34286)] and a
spacer (B) [Commercial service tool].
30. Remove oil channel (2) from clutch housing.
31. Remove bushing (1) from clutch housing, using a remover
[Commercial service tool].
PCIB1706E
PCIB1708E
PCIB1714E
JPDIC0107ZZ
PCIB1717E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст