Nissan Juke F15. Manual — part 728
EXL-132
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
DIAGNOSIS SYSTEM (BCM)
NOTE:
*: Power position shifts to “LOCK” from “OFF”, when ignition switch is in the OFF position, selector lever is in the P position (A/T models
and CVT models), and any of the following conditions are met.
• Closing door
• Opening door
• Door is locked using door request switch
• Door is locked using Intelligent Key
The power position shifts to “ACC” when the push-button ignition switch (push switch) is pushed at “LOCK”.
HEADLAMP
HEADLAMP : CONSULT Function (BCM - HEAD LAMP) (HALOGEN TYPE)
INFOID:0000000012201734
WORK SUPPORT
CONSULT screen item
Indication/Unit
Description
Vehicle Speed
km/h
Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter
km
Total mileage (Odometer value) of the moment a particular DTC is detected
Vehicle Condition
SLEEP>LOCK
Power position status of
the moment a particular
DTC is detected
While turning BCM status from low power consumption mode to
normal mode (Power position is “LOCK”*.)
SLEEP>OFF
While turning BCM status from low power consumption mode to
normal mode (Power position is “OFF”.)
LOCK>ACC
While turning power position from “LOCK”* *to “ACC”
ACC>ON
While turning power position from “ACC” to “IGN”
RUN>ACC
While turning power position from “RUN” to “ACC” (Vehicle is
stopping and selector lever is except P position.)
CRANK>RUN
While turning power position from “CRANKING” to “RUN” (From
cranking up the engine to run it)
RUN>URGENT
While turning power position from “RUN“ to “ACC” (Emergency
stop operation)
ACC>OFF
While turning power position from “ACC” to “OFF”
OFF>LOCK
While turning power position from “OFF” to “LOCK”*
OFF>ACC
While turning power position from “OFF” to “ACC”
ON>CRANK
While turning power position from “IGN” to “CRANKING”
OFF>SLEEP
While turning BCM status from normal mode (Power position is
“OFF”.) to low power consumption mode
LOCK>SLEEP
While turning BCM status from normal mode (Power position is
“LOCK”*.) to low power consumption mode
LOCK
Power position is “LOCK”*
OFF
Power position is “OFF” (Ignition switch OFF)
ACC
Power position is “ACC” (Ignition switch ACC)
ON
Power position is “IGN” (Ignition switch ON with engine stopped)
ENGINE RUN
Power position is “RUN” (Ignition switch ON with engine running)
CRANKING
Power position is “CRANKING” (At engine cranking)
IGN Counter
0 - 39
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition
whenever ignition switch OFF
→ ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
DIAGNOSIS SYSTEM (BCM)
EXL-133
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
*
1
: For models without auto light system, this item cannot be used.
*
2
: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Service item
Setting item
Setting
CUSTOM A/LIGHT SETTING*
1
MODE1*
2
Normal
MODE2
More sensitive setting than normal setting (Turns ON earlier than normal operation)
MODE3
More sensitive setting than MODE2 (Turns ON earlier than MODE2)
MODE4
Less sensitive setting than normal setting (Turns ON later than normal operation)
BATTERY SAVER SET
On*
2
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
ILL DELAY SET*
1
MODE1*
2
45 sec.
Sets delay timer function timer operation time.
(All doors closed)
MODE2
Without the function
MODE3
30 sec.
MODE4
60 sec.
MODE5
90 sec.
MODE6
120 sec.
MODE7
150 sec.
MODE8
180 sec.
HEAD LIGHT TIMER
MODE1
10 sec.
Sets follow me home function activating time
MODE2*
2
30 sec.
AUTO LIGHT LOGIC SET*
1
MODE1*
2
With twilight ON custom & with wiper INT, LO and HI
MODE2
With twilight ON custom & with wiper LO and HI
MODE3
With twilight ON custom & without
MODE4
Without twilight ON custom & with wiper INT, LO and HI
MODE5
Without twilight ON custom & with wiper LO and HI
MODE6
Without twilight ON custom & without
Monitor item
[Unit]
Description
PUSH SW
[On/Off]
Indicates [On/Off] condition of push-button ignition switch
ENGINE STATE
[STOP/STALL/CRANK/RUN]
Indicates [STOP/STALL/CRANK/RUN] condition of engine states
VEH SPEED 1
[km/h]
Display the vehicle speed signal received from combination meter by numerical value [km/h]
EXL-134
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
DIAGNOSIS SYSTEM (BCM)
*
1
: For models without auto light system, this item cannot be monitored.
*
2
: For models without front fog lamp, this item cannot be monitored.
ACTIVE TEST
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off]
HI BEAM SW
[On/Off]
HEAD LAMP SW 1
[On/Off]
HEAD LAMP SW 2
[On/Off]
PASSING SW
[On/Off]
AUTO LIGHT SW*
1
[On/Off]
FR FOG SW*
2
[On/Off]
DOOR SW-DR
[On/Off]
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
[On/Off]
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
[On/Off]
Indicated [On/Off] condition of rear door switch RH
DOOR SW-RL
[On/Off]
Indicated [On/Off] condition of rear door switch LH
DOOR SW-BK
[On/Off]
Indicated [On/Off] condition of back door switch
OPTI SEN (DTCT)
[V]
The value of outside brightness voltage input from the optical sensor
OPTI SEN (FILT)
[V]
The value of outside brightness voltage filtered by BCM
OPTICAL SENSOR
[On/Off/NG]
NOTE:
This item cannot be monitored
Monitor item
[Unit]
Description
Test item
Operation
Description
TAIL LAMP
On
• Transmits the position light request signal to IPDM E/R via CAN communication to
turn the parking, license plate and tail lamps ON
• Transmits the position light request signal to combination meter via CAN commu-
nication to turn the position lamp indicator lamp ON
Off
Stops the position light request signal transmission
HEAD LAMP
HI
• Transmits the high beam request signal to IPDM E/R via CAN communication to
turn the headlamp (HI) ON
• Transmits the high beam request signal to combination meter via CAN communi-
cation to turn the high beam indicator lamp ON
Low
Transmits the low beam request signal to IPDM E/R via CAN communication to turn
the headlamp (LO) ON
Off
Stops the high beam request signal and low beam request signal transmission
DIAGNOSIS SYSTEM (BCM)
EXL-135
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
*
1
: For models without front fog lamp and except for NISMO models with daytime running light system, this
item cannot be tested.
*
2
: For models without daytime running light system and NISMO models with daytime running light system,
this item cannot be tested.
FLASHER
FLASHER : CONSULT Function (BCM - FLASHER) (HALOGEN TYPE)
INFOID:0000000012201735
WORK SUPPORT
*: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
FR FOG LAMP*
1
On
• Transmits the front fog light request signal to IPDM E/R via CAN communication
to turn the front fog lamp ON (With front fog lamp)
• Transmits the daytime running light request signal to IPDM E/R via CAN commu-
nication to turn the daytime running light ON (NISMO models with daytime running
light system)
Off
• Stops the front fog light request signal transmission (With front fog lamp)
• Stops the front fog light request signal transmission (NISMO models with daytime
running light system)
DAYTIME RUNNING LIGHT*
2
On
Transmits the daytime running light request signal to IPDM E/R via CAN communi-
cation to turn the headlamp (HI) ON [Headlamp (HI) at approximately half illumina-
tion]
Off
Stops the daytime running light request signal transmission
ILL DIM SIGNAL
On
NOTE:
This item cannot be tested
Off
Test item
Operation
Description
Service item
Setting item
Setting
HAZARD ANSWER BACK
Lock
Only
With locking only
Sets the hazard warning lamp answer back function when
the door is lock/unlock with the door request switch and In-
telligent Key
Unlock
Only
With unlocking only
Lock/
Unlock*
With locking/unlocking
Off
Without the function
Monitor item
[Unit]
Description
REQ SW -DR
[On/Off]
Indicates [On/Off] condition of door request switch (driver side)
REQ SW -AS
[On/Off]
Indicates [On/Off] condition of door request switch (passenger side)
PUSH SW
[On/Off]
Indicates [On/Off] condition of push-button ignition switch
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function
TURN SIGNAL L
[On/Off]
HAZARD SW
[On/Off]
The switch status input from the hazard switch
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст