Nissan Juke F15. Manual — part 796
FL-14
< REMOVAL AND INSTALLATION >
[MR16DDT ]
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
3. Install sub fuel level sensor assembly (1) with its matching mark
(A) aligned with fuel tank matching mark (B) as shown in the fig-
ure.
NOTE:
• Figure shows fuel level sensor unit, fuel filter and fuel pump
assembly side of fuel tank.
• For sub fuel level sensor assembly matching mark is located
on the fuel tank of the vehicle rear side.
4. Install lock ring for sub fuel level sensor assembly with lock ling
wrench (A) by turning clockwise.
Fuel Level Sensor Unit, Fuel Filter and Fuel Pump Assembly
1. Temporarily install the O-ring to the fuel level sensor unit, fuel filter and fuel pump assembly.
2. Connect the fuel tube as per the following steps.
• Insert the quick connector (A) straight to the fuel level sensor
unit, fuel filter and fuel pump assembly.
• Judge a good fit from connecting sound and tactile feedback.
• Pull the fuel tube by hand to check a secure fit.
3. Connect harness connector (B).
4. Insert the fuel level sensor unit, fuel filter and fuel pump assembly to the fuel tank.
CAUTION:
• Never bend float arm during installation.
• To install, fuel tube (1) must run to the front (
) of the vehicle to avoid the interference with the
float arm (2), as shown in the figure.
: Vehicle front
JPBIA4468ZZ
Tool number (A)
: KV991J0090 (J-46214) (shown)
: KV101207S0 ( — )
JPBIA4463ZZ
JPBIA4465ZZ
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-15
< REMOVAL AND INSTALLATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
• Through the clearance of the mounting part of the fuel level sensor unit and the fuel filter and
fuel pump assembly, visually check that the fuel tube is placed on the vehicle front side of them.
5. Install fuel level sensor unit, fuel filter and fuel pump assembly
(1) with its matching mark (A) aligned with fuel tank matching
mark (B) as shown in the figure.
6. Install lock ring for sub fuel level sensor assembly with lock ling
wrench (A) by turning clockwise.
7. Connect quick connector of fuel feed tube as per following procedures.
a. Check the connection for damage or any foreign materials.
b. Align the connector with the tube, then insert the connector straight into the tube until a “click” sound is
heard.
c. After connecting, check that the connection is secured with following procedures.
• Visually confirm that the two tabs are connected to the connector.
: Vehicle front
JPBIA4467ZZ
JPBIA4469ZZ
Tool number (A)
: KV991J0090 (J-46214) (shown)
: KV101207S0 ( — )
JPBIA4463ZZ
FL-16
< REMOVAL AND INSTALLATION >
[MR16DDT ]
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
• Pull (A) the tube and the connector to check that they are
securely connected.
8. Connect harness connector.
Inspection Hole Cover
• Before installing inspection hole cover, check that the connecting part has no fuel leakage. Refer to
1. Install inspection hole covers with the front mark (arrow) facing front of vehicle.
AWD : Disassembly and Assembly
INFOID:0000000012197589
DISASSEMBLY
CAUTION:
Sub fuel level sensor unit cannot be disassembled and should be replaced as a unit.
1. Disconnect harness connector (A).
2. Press (A) with a flat-blade screwdriver or an equivalent to
release lock and push out the fuel level senor unit (1).
3. To remove the fuel level sensor unit (1), side it in the direction
(
) of the arrow with the lock release.
ASSEMBLY
JPBIA0140ZZ
JPBIA4471ZZ
JPBIA4472ZZ
JPBIA4473ZZ
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-17
< REMOVAL AND INSTALLATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
1. Check for damage of fuel level sensor unit installation position on the side of fuel filter and pump assem-
bly.
2. Slide fuel level sensor unit until it aligns to installation groove, then insert it until stops.
• After inserting, apply force in reverse direction (removal direction) to ensure it cannot be pulled out.
3. Connect harness connector.
AWD : Inspection
INFOID:0000000012197590
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leakage.
1. Turn ignition switch “ON” (with engine stopped), then check connections for leakage by applying fuel pres-
sure to fuel piping.
2. Start engine and let it idle and check there are no fuel leakage at the fuel system connections.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст