Nissan Juke F15. Manual — part 1145
SEC-104
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B20A0 CRANKING REQUEST CIRCUIT
5. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
REPLACE IPDM E/R
1. Replace IPDM E/R. Refer to
PCS-37, "Removal and Installation"
.
2. Perform DTC CONFIRMATION PROCEDURE for DTC B20A0. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE ECM
Replace ECM.
EC-590, "Removal and Installation"
.
>> INSPECTION END
IPDM E/R
ECM
Continuity
Connector
Terminal
Connector
Terminal
E13
23
F26
92
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E13
23
Not existed
B210B STARTER CONTROL RELAY
SEC-105
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B210B STARTER CONTROL RELAY
DTC Logic
INFOID:0000000012202206
DTC DETECTION LOGIC
NOTE:
If DTC B210B is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE 1
1. Press push-button ignition switch under the following conditions to start engine, and wait 5 seconds or
more.
CVT models
-
Selector lever: In the P position
-
Brake pedal: Depressed
M/T models
-
Shift lever: In the Neutral position
-
Clutch pedal: Depressed
2. Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?
YES
>> Go to
SEC-105, "Diagnosis Procedure"
.
NO (M/T models)>>INSPECTION END
NO (CVT models)>>GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE 2
1. Stop engine.
2. Perform DTC CONFIRMATION PROCEDURE for DTC P1650. Refer to
3. Turn ignition switch ON.
4. Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?
YES
>> Refer to
SEC-105, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012202207
1.
CHECK SELF DIAGNOSTIC RESULT
Select “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
What is the display history of DTC “B210B”?
“CRNT”>> Replace IPDM E/R. Refer to
PCS-37, "Removal and Installation"
.
“PAST” >> GO TO 2.
2.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B210B
STR CONT RLY ON CIRC
When comparing the following items, IPDM E/R detects
that starter control relay is stuck in the ON position for
5 seconds or more.
• Starter control relay signal (CAN) from BCM
• Starter relay status signal (CAN) from BCM
• Starter control relay and starter relay status signal
(IPDM E/R input)
• Starter control relay control signal (IPDM E/R output)
• P/N position signal input
• Ignition power supply No.2 signal from BCM
• Harness or connectors
(CAN communication line is
open or shorted.
(Ignition power supply No.2
circuit is open or shorted.)
• IPDM E/R
• BCM
SEC-106
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B210B STARTER CONTROL RELAY
>> INSPECTION END
B210C STARTER CONTROL RELAY
SEC-107
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B210C STARTER CONTROL RELAY
DTC Logic
INFOID:0000000012202208
DTC DETECTION LOGIC
NOTE:
• If DTC B210C is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• When IPDM E/R power supply voltage is low (Approx. 7 - 8 V for about 1 second), the DTC B210C may be
detected.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Press push-button ignition switch under the following conditions to start engine, and wait 5 seconds or
more.
CVT models
-
Selector lever: In the P position
-
Brake pedal: Depressed
M/T models
-
Shift lever: In the Neutral position
-
Clutch pedal: Depressed
2. Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?
YES
>> Go to
SEC-107, "Diagnosis Procedure"
.
NO (M/T models)>>INSPECTION END
NO (CVT models)>>GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE 2
1. Stop engine.
2. Perform DTC CONFIRMATION PROCEDURE for DTC P1650. Refer to
3. Turn ignition switch ON.
4. Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?
YES
>> Refer to
SEC-107, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012202209
1.
CHECK SELF DIAGNOSTIC RESULT
Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
What is the display history of DTC “B210C”?
“CRNT”>> GO TO 3.
“PAST” >> GO TO 2.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B210C
STR CONT RLY OFF CIRC
When comparing the following items, IPDM E/R
detects that starter control relay is stuck in the
OFF position for 5 seconds or more.
• Starter control relay signal (CAN) from BCM
• Starter relay status signal (CAN) from BCM
• Starter control relay and starter relay status
signal (IPDM E/R input)
• Starter control relay control signal (IPDM E/R
output)
• P/N position signal input
• Ignition power supply No.2 signal from BCM
• Harness or connectors
(CAN communication line is
open or shorted.
(Ignition power supply No.2
circuit is open or shorted.)
• IPDM E/R
• BCM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст