Nissan Juke F15. Manual — part 1229
TM-106
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52H]
TRANSAXLE ASSEMBLY
f.
While rotating shifter lever A (1) in the direction of the arrow
shown, assemble transaxle case to clutch housing.
g. Accessing from the bore plug hole, expand snap ring at main-
shaft rear bearing so that the ring catches the periphery of main-
shaft rear bearing.
h. Temporarily tighten transaxle case bolts.
i.
Shift the shifter lever A (1) to 2nd gear position.
NOTE:
• The 2nd gear position is attained when shifter lever A is in the
position shown.
• When transaxle is shifted to the 2nd gear position, mainshaft
assembly is lifted.
j.
Seat snap ring in the groove on mainshaft rear bearing. If snap
ring is not seated in the groove on mainshaft rear bearing,
remove transaxle case and repeat the procedure from step d.
2
: shifter lever B
PCIB1929E
PCIB1840E
PCIB1809E
SCIA0893E
TRANSAXLE ASSEMBLY
TM-107
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52H]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
k. Tighten transaxle case bolts to the specified torque.
l.
Shift the shifter lever A (1) to neutral position.
NOTE:
The neutral position is attained when shifter lever A is in the
position shown.
27. Install bore plug to transaxle case using Tool.
CAUTION:
Do not reuse bore plug.
28. Install selector lever to transaxle case and then install retaining
pin to selector lever.
CAUTION:
• Do not reuse retaining pin.
• Assemble retaining pin from the direction shown by the
arrow until it becomes flush with the end surface of selec-
tor lever.
29. Install guide bolt following the procedures below.
a. Shift the shifter lever A and selector lever to neutral position.
PCIB1838E
PCIB1930E
Tool number
: ST33061000 (J-8107-2))
PCIB0941E
PCIB1837E
TM-108
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52H]
TRANSAXLE ASSEMBLY
b. Visually confirm from the guide bolt hole (C) that the lever is
securely set to neutral position (A). If it is not in the neutral posi-
tion, repeat the procedure from step a.
CAUTION:
The guide groove (D) of striking rod assembly will be dam-
aged when assembling guide bolt with the lever is in except
neutral position (B).
c.
Check continuity between terminals of park/neutral position
(PNP) switch to confirm it in the neutral position. If it is not in the
neutral position, remove park/neutral position (PNP) switch and
repeat the procedure from step a. Refer to
TRAL POSITION (PNP) SWITCH : Component Inspection"
d. Install guide bolt to transaxle case and then tighten guide bolt to
the specified torque.
CAUTION:
Do not reuse guide bolt.
30. Apply recommended sealant to threads of park/neutral position
(PNP) switch (1). Then install it to transaxle case and tighten to
the specified torque.
• Use Genuine Silicone RTV or an equivalent. Refer to
CAUTION:
Remove old sealant and oil adhering to threads.
31. Install plunger to transaxle case.
32. Apply recommended sealant to threads of back-up lamp switch
(2). Then install it to transaxle case and tighten to the specified
torque.
• Use Genuine Silicone RTV or an equivalent. Refer to
CAUTION:
Remove old sealant and oil adhering to threads.
33. Install air breather tube (3) to transaxle case.
CAUTION:
• Do not reuse air breather tube.
• Assemble air breather tube until its collar element contacts with transaxle case.
1
: Guide bolt
PCIB1890E
PCIB1836E
PCIB1835E
TRANSAXLE ASSEMBLY
TM-109
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52H]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
34. Install gasket onto plug and then install them into transaxle
case. Tighten plug to the specified torque.
CAUTION:
Do not reuse gasket.
35. Install gasket onto drain plug and then install them into clutch
housing. Tighten drain plug to the specified torque.
CAUTION:
Do not reuse gasket.
36. Install O-ring onto plug and then install it into clutch housing.
Tighten bolt to the specified torque.
CAUTION:
• Do not reuse O-ring.
• After oil is filled, tighten bolt to specified torque.
Adjustment
INFOID:0000000012200823
ADJUSTMENT
Differential Side Bearing Preload
• When adjusting differential side bearing preload, select adjusting
shim for differential side bearing. To select adjusting shim, mea-
sure clearance (L) between transaxle case and differential side
bearing outer race. Refer to
CAUTION:
Up to 2 adjusting shims can be selected.
• Calculate dimension (L) (thickness of adjusting shim) using the fol-
lowing procedure to satisfy specification of preload for differential
side bearing.
PCIB1865E
PCIB1834E
PCIB1969E
Preload
: Refer to
Dimension L = (L
1
- L
2
) + Preload
L
: Thickness of adjusting shim
L
1
: Distance between transaxle case end face
and mounting face of adjusting shim
L
2
: Distance between differential side bearing
outer race and clutch housing end face
JSDIA5280GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст