Nissan Juke F15. Manual — part 1179
B1430 SEAT BELT PRE-TENSIONER
SRC-81
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1430 SEAT BELT PRE-TENSIONER
DTC Description
INFOID:0000000012199636
DTC DETECTION LOGIC
POSSIBLE CAUSE
[B1430–09, B1430–1A]
• Connection malfunction or short circuit of harness and connector
• Internal malfunction of seat belt pre-tensioner LH
• Internal malfunction of air bag diagnosis sensor unit
[B1430–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of seat belt pre-tensioner LH
• Internal malfunction of air bag diagnosis sensor unit
[B1430–12]
• Connection malfunction or short circuit to power supply of harness and connector
• Internal malfunction of seat belt pre-tensioner LH
• Internal malfunction of air bag diagnosis sensor unit
[B1430–13]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of seat belt pre-tensioner LH
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to
SRC-10, "On Board Diagnosis Function"
.
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B1430–09
PRE-TEN FRONT LH
[front seat belt pre-tensioner
squib left hand component fail-
ures (cross connection)]
[SHORT]
Seat belt pre-tensioner LH circuits are shorted to each other
B1430–11
PRE-TEN FRONT LH
(front seat belt pre-tensioner
squib left hand circuit short to
GND)
[GND-SHORT]
Seat belt pre-tensioner LH circuit is shorted to ground
B1430–12
PRE-TEN FRONT LH
(front seat belt pre-tensioner
squib left hand circuit short to
battery)
[VB-SHORT]
Seat belt pre-tensioner LH circuit is shorted to power supply circuit
B1430–13
PRE-TEN FRONT LH
(front seat belt pre-tensioner
squib left hand circuit)
[OPEN]
Seat belt pre-tensioner LH circuit is open
B1430–1A
PRE-TEN FRONT LH
(front seat belt pre-tensioner
squib left hand circuit resistance
below threshold)
[SHORT]
Seat belt pre-tensioner LH circuits are shorted to each other
SRC-82
< DTC/CIRCUIT DIAGNOSIS >
B1430 SEAT BELT PRE-TENSIONER
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
.
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012199637
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector for disconnection, looseness or damage.
Is the inspection result normal?
YES
>> GO TO 2.
NO–1 >> Damage: Replace malfunctioning harness and connector.
NO–2 >> Disconnection or looseness: Securely lock the connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace malfunctioning harness and connector.
3.
REPLACE SEAT BELT PRE-TENSIONER LH
1. Replace seat belt pre-tensioner LH. Refer to
SR-31, "Removal and Installation"
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to
SR-29, "Removal and Installation"
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
B1431 SEAT BELT PRE-TENSIONER
SRC-83
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1431 SEAT BELT PRE-TENSIONER
DTC Description
INFOID:0000000012199638
DTC DETECTION LOGIC
POSSIBLE CAUSE
[B1431–09, B1431–1A]
• Connection malfunction or short circuit of harness and connector
• Internal malfunction of seat belt pre-tensioner RH
• Internal malfunction of air bag diagnosis sensor unit
[B1431–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of seat belt pre-tensioner RH
• Internal malfunction of air bag diagnosis sensor unit
[B1431–12]
• Connection malfunction or short circuit to power supply of harness and connector
• Internal malfunction of seat belt pre-tensioner RH
• Internal malfunction of air bag diagnosis sensor unit
[B1431–13]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of seat belt pre-tensioner RH
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to
SRC-10, "On Board Diagnosis Function"
.
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B1431–09
PRE-TEN FRONT RH
[front seat belt pre-tensioner
squib right hand component
failures (cross connection)]
[SHORT]
Seat belt pre-tensioner RH circuits are shorted to each other
B1431–11
PRE-TEN FRONT RH
(front seat belt pre-tensioner
squib right hand circuit short
to GND)
[GND-SHORT]
Seat belt pre-tensioner RH circuit is shorted to ground
B1431–12
PRE-TEN FRONT RH
(front seat belt pre-tensioner
squib right hand circuit short
to battery)
[VB-SHORT]
Seat belt pre-tensioner RH circuit is shorted to power supply circuit
B1431–13
PRE-TEN FRONT RH
(front seat belt pre-tensioner
squib right hand circuit)
[OPEN]
Seat belt pre-tensioner RH circuit is open
B1431–1A
PRE-TEN FRONT RH
(front seat belt pre-tensioner
squib right hand circuit re-
sistance below threshold)
[SHORT]
Seat belt pre-tensioner RH circuits are shorted to each other
SRC-84
< DTC/CIRCUIT DIAGNOSIS >
B1431 SEAT BELT PRE-TENSIONER
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
.
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012199639
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector for disconnection, looseness or damage.
Is the inspection result normal?
YES
>> GO TO 2.
NO–1 >> Damage: Replace malfunctioning harness and connector.
NO–2 >> Disconnection or looseness: Securely lock the connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace malfunctioning harness and connector.
3.
REPLACE SEAT BELT PRE-TENSIONER RH
1. Replace seat belt pre-tensioner RH. Refer to
SR-31, "Removal and Installation"
.
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to
SR-29, "Removal and Installation"
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст