Nissan Juke F15. Manual — part 1178
B1422 SIDE COLLISION DETECTION
SRC-77
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1422 SIDE COLLISION DETECTION
DTC Description
INFOID:0000000012199630
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Malfunction of side-related parts
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to
SRC-10, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012199631
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
PERFORM COLLISION DIAGNOSIS
Perform collision diagnosis. Refer to
SR-8, "FOR SIDE AND ROLLOVER COLLISION : When SRS is acti-
SR-9, "FOR SIDE AND ROLLOVER COLLISION : When SRS is not activated in a colli-
.
>> GO TO 2.
2.
FINAL INSPECTION
Perform “AIR BAG” Self Diagnostic Result.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis of applicable DTC. Refer to
.
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B1422–00
SIDE COLLISION
(Firing Record, Side)
Side air bag and curtain air bag are deployed
SRC-78
< DTC/CIRCUIT DIAGNOSIS >
B1425 REAR COLLISION DETECTION
B1425 REAR COLLISION DETECTION
DTC Description
INFOID:0000000012199632
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Malfunction of rear crash-related parts
• Internal malfunction of air bag diagnosis sensor unit
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to
SRC-10, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
.
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012199633
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
PERFORM COLLISION DIAGNOSIS
Perform collision diagnosis. Refer to
SR-8, "FOR SIDE AND ROLLOVER COLLISION : When SRS is acti-
SR-9, "FOR SIDE AND ROLLOVER COLLISION : When SRS is not activated in a colli-
>> GO TO 2.
2.
FINAL INSPECTION
Perform “AIR BAG” Self Diagnostic Result.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis of applicable DTC. Refer to
.
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B1425–00
REAR COLLISION
(Rear Crash Detect)
Rear collision detected
B142A IGN VOLTAGE
SRC-79
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B142A IGN VOLTAGE
DTC Description
INFOID:0000000012199634
DTC DETECTION LOGIC
POSSIBLE CAUSE
[B142A–16]
• Malfunction of battery voltage (low voltage)
• Connection malfunction of harness or connector
• Internal malfunction of air bag diagnosis sensor unit
[B142A–17]
• Malfunction of battery voltage (high voltage)
• Connection malfunction of harness or connector
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to
SRC-10, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012199635
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK BATTERY VOLTAGE
Check battery voltage.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace battery. Refer to
PG-105, "Removal and Installation"
2.
CHECK HARNESS CONNECTOR
Check the harness connector for disconnection, looseness or damage.
Is the inspection result normal?
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B142A–16
IGNITION VOLTAGE
(Ignition voltage Low)
[VB-LOW]
Power supply malfunction (low voltage) of air bag diagnosis sensor unit
B142A–17
IGNITION VOLTAGE
(Ignition voltage High)
[VB-HIGH]
Power supply malfunction (high voltage) of air bag diagnosis sensor unit
SRC-80
< DTC/CIRCUIT DIAGNOSIS >
B142A IGN VOLTAGE
YES
>> GO TO 3.
NO–1 >> Damage: Replace malfunctioning harness and connector.
NO–2 >> Disconnection or looseness: Securely lock the connector.
3.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace malfunctioning harness and connector.
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to
SR-29, "Removal and Installation"
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст