Nissan Juke F15. Manual — part 618
EM-26
< REMOVAL AND INSTALLATION >
[MR FOR NISMO RS MODELS]
ENGINE COVER
REMOVAL AND INSTALLATION
ENGINE COVER
Exploded View
INFOID:0000000012197250
Removal and Installation
INFOID:0000000012197251
REMOVAL
Remove engine cover.
CAUTION:
Never damage or scratch engine cover when installing or removing.
INSTALLATION
Install in the reverse order of removal.
1.
Engine cover
2.
Mounting rubber (Black)
3.
Mounting rubber (Gray)
JPBIA4311ZZ
AIR CLEANER AND AIR DUCT
EM-27
< REMOVAL AND INSTALLATION >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
AIR CLEANER AND AIR DUCT
Exploded View
INFOID:0000000012197252
Removal and Installation
INFOID:0000000012197253
REMOVAL
NOTE:
Mass air flow sensor is removable under the car-mounted condition.
1. Remove engine cover. Refer to
.
2. Remove air duct inlet (upper).
3. Remove the air cleaner filter from the air cleaner case.
4. Disconnect mass air flow sensor harness connector, and remove harness clamp from air cleaner body.
5. Remove air cleaner body assembly.
6. Remove the air duct (suction side).
• Add matching marks if necessary for easier installation.
1.
Mass air flow sensor
2.
Gasket
3.
Clamp
4.
Air duct (suction side)
5.
Clamp
6.
Air cleaner cover assembly
7.
Mounting rubber
8.
Air cleaner filter
9.
Air cleaner body assembly
10. Air duct inlet (lower)
11. Grommet
12. Air duct inlet (upper)
13. Grommet
14. Bracket
15. Mounting rubber
A.
To turbocharger
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
JPBIA4305GB
EM-28
< REMOVAL AND INSTALLATION >
[MR FOR NISMO RS MODELS]
AIR CLEANER AND AIR DUCT
7. Remove air cleaner cover assembly.
8. Remove mass air flow sensor from air cleaner cover, if necessary.
CAUTION:
Handle the mass air flow sensor with following cares.
• Never shock the mass air flow sensor.
• Never disassemble the mass air flow sensor.
• Never touch the sensor of the mass air flow sensor.
9. Remove air duct inlet (lower) with the following procedure.
a. Remove fender protector (LH). Refer to
.
b. Remove air duct inlet (lower).
INSTALLATION
Note the following, and install in the reverse order of removal.
• Align marks. Attach each joint. Screw clamps firmly.
• Fixing clips shall be fixed after inserting air cleaner body assembly protrusion to air cleaner case botch hole.
• Make sure whether air cleaner body has been firmly installed by shaking it.
Inspection
INFOID:0000000012197254
INSPECTION AFTER REMOVAL
Inspect air duct and resonator assembly for crack or tear.
• If anything found, replace air duct and resonator assembly.
INTAKE MANIFOLD
EM-29
< REMOVAL AND INSTALLATION >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
INTAKE MANIFOLD
Exploded View
INFOID:0000000012197255
1.
Clamp
2.
Water hose
3.
PCV hose
4.
Gasket
5.
Intake manifold
6.
Vacuum tube
7.
Vacuum hose (with check valve)
8.
Vacuum hose
9.
Vacuum gallery assembly
10. EVAP hose
11. EVAP check valve
12. EVAP hose
13.
EVAP canister purge volume control
solenoid valve
14. Bracket
15. Bracket
16. EVAP hose
17. EVAP service port
18. EVAP hose
19. EVAP tube
20. EVAP hose
21. Water hose
22. Electric throttle control actuator
23. Gasket
A.
To turbocharger
B.
To centralized under-floor piping
C.
To recirculation valve hose
D.
To break booster hose
: N·m (kg-m, ft-lb)
JSBIA5991GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст