Nissan Juke F15. Manual — part 713

EXL-72

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

TURN SIGNAL LAMP CIRCUIT

YES

>> Replace BCM. Refer to

BCS-94, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK TURN SIGNAL LAMP POWER SUPPLY CIRCUIT (OPEN)

1. Turn ignition switch OFF.

2. Disconnect BCM connector.

3. Check continuity between BCM harness connector and each turn signal lamp harness connector.

Front turn signal lamp

Side turn signal lamp

Rear turn signal lamp

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK TURN SIGNAL LAMP GROUND CIRCUIT

Check continuity between each turn signal lamp harness connector and ground.

Front turn signal lamp

Side turn signal lamp

Rear turn signal lamp

Is the inspection result normal?

YES-1 >> Front turn signal lamp or rear turn signal lamp: GO TO 5.

YES-2 >> Side turn signal lamp: Replace the corresponding side turn signal lamp. Refer to

EXL-104,

"Removal and Installation"

.

NO

>> Repair or replace harness.

BCM

Front turn signal lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

M69

61

E47

1

Existed

LH

60

E34

BCM

Door mirror

Continuity

Connector

Terminal

Connector

Terminal

RH

M69

61

D9

13

Existed

LH

60

D30

BCM

Rear combination lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

M69

61

B59

5

Existed

LH

60

B80

Front turn signal lamp

—

Continuity

Connector

Terminal

RH

E47

2

Ground

Existed

LH

E34

Door mirror

—

Continuity

Connector

Terminal

RH

D9

2

Ground

Existed

LH

D30

Rear combination lamp

—

Continuity

Connector

Terminal

RH

B59

3

Ground

Existed

LH

B80

TURN SIGNAL LAMP CIRCUIT

EXL-73

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

5.

CHECK TURN SIGNAL LAMP BULB

Check the applicable turn signal lamp bulb.
Is the inspection result normal?

YES-1 >> Front turn signal lamp: Check the corresponding front turn signal lamp bulb socket. Repair or

replace if necessary.

YES-2 >> Rear turn signal lamp: Check the corresponding rear turn signal lamp bulb socket and harness.

Repair or replace if necessary.

NO

>> Replace the corresponding turn signal lamp bulb. Refer to

EXL-100, "Replacement"

(front turn

signal lamp) or

EXL-109, "Replacement"

(rear turn signal lamp).

EXL-74

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

OPTICAL SENSOR

OPTICAL SENSOR

Component Function Check

INFOID:0000000012201659

1.

CHECK OPTICAL SENSOR SIGNAL

With CONSULT

1. Turn ignition switch ON.

2. Select “HEAD LAMP” of “BCM” using CONSULT.

3. Select “OPTI SEN (DTCT)” in “Data Monitor” mode.

4. Turn lighting switch AUTO.

5. With the optical sensor illuminating, check the monitor status.

*: Illuminates the optical sensor. The value may be less than the standard value if brightness is weak.
Is the inspection result normal?

YES

>> Optical sensor is normal.

NO

>> Refer to

EXL-74, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012201660

1.

CHECK OPTICAL SENSOR POWER SUPPLY

1. Turn ignition switch ON.

2. Turn lighting switch AUTO.

3. Check voltage between optical sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 4.

2.

CHECK OPTICAL SENSOR GROUND

Check voltage between optical sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 6.

3.

CHECK OPTICAL SENSOR SIGNAL

With illuminating the optical sensor, check voltage between optical sensor harness connector and ground.

Monitor item

Condition

Voltage

(Approx.)

OPTI SEN (DTCT) Optical sensor

When illuminating

3.1 V or more *

When shutting off light

0.6 V or less

+

-

Voltage

(Approx.)

Optical sensor

Connector

Terminal

M84

1

Ground

5 V

+

-

Voltage

(Approx.)

Optical sensor

Connector

Terminal

M84

3

Ground

0 V

OPTICAL SENSOR

EXL-75

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

*: Illuminate the optical sensor. The value may be less than the standard if brightness is weak.
Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Replace optical sensor. Refer to

EXL-105, "Removal and Installation"

.

4.

CHECK OPTICAL SENSOR POWER SUPPLY CIRCUIT (OPEN)

1. Turn ignition switch OFF.

2. Disconnect optical sensor connector and BCM connector.

3. Check continuity between optical sensor harness connector and BCM harness connector.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace harness.

5.

CHECK OPTICAL SENSOR POWER SUPPLY CIRCUIT (SHORT)

Check continuity between optical sensor harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to

BCS-94, "Removal and Installation"

.

NO

>> Repair or replace harness.

6.

CHECK OPTICAL SENSOR GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect optical sensor connector and BCM connector.

3. Check continuity between optical sensor harness connector and BCM harness connector.

Is the inspection result normal?

YES

>> Replace BCM. Refer to

BCS-94, "Removal and Installation"

.

NO

>> Repair or replace harness.

7.

CHECK OPTICAL SENSOR SIGNAL CIRCUIT (OPEN)

1. Turn ignition switch OFF.

2. Disconnect optical sensor connector and BCM connector.

3. Check continuity between optical sensor harness connector and BCM harness connector.

+

-

Condition

Voltage

(Approx.)

Optical sensor

Connector

Terminal

M84

2

Ground

Optical sensor

When illuminating

3.1 V or more*

When shutting off light

0.6 V or less

Optical sensor

BCM

Continuity

Connector

Terminal

Connector

Terminal

M84

1

M68

17

Existed

Optical sensor

—

Continuity

Connector

Terminal

M84

1

Ground

Not existed

Optical sensor

BCM

Continuity

Connector

Terminal

Connector

Terminal

M84

3

M68

18

Existed