Nissan Juke F15. Manual — part 1171
B0021 CURTAIN AIR BAG MODULE
SRC-49
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector for disconnection, looseness or damage.
Is the inspection result normal?
YES
>> GO TO 2.
NO–1 >> Damage: Replace malfunctioning harness and connector.
NO–2 >> Disconnection or looseness: Securely lock the connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace malfunctioning harness and connector.
3.
REPLACE CURTAIN AIR BAG MODULE LH
1. Replace curtain air bag module LH. Refer to
SR-21, "Removal and Installation"
.
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to
SR-29, "Removal and Installation"
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
SRC-50
< DTC/CIRCUIT DIAGNOSIS >
B0028 SIDE AIR BAG MODULE
B0028 SIDE AIR BAG MODULE
DTC Description
INFOID:0000000012199602
DTC DETECTION LOGIC
POSSIBLE CAUSE
[B0028–09, B0028–1A]
• Connection malfunction or short circuit of harness and connector
• Internal malfunction of side air bag module RH
• Internal malfunction of air bag diagnosis sensor unit
[B0028–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of side air bag module RH
• Internal malfunction of air bag diagnosis sensor unit
[B0028–12]
• Connection malfunction or short circuit to power supply of harness and connector
• Internal malfunction of side air bag module RH
• Internal malfunction of air bag diagnosis sensor unit
[B0028–13]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of side air bag module RH
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to
SRC-10, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
.
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012199603
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B0028–09
SIDE A/B MODULE RH
[Right Side Airbag Deploy-
ment Control (Subfault)]
[SHORT]
Side air bag module RH circuits are shorted to each other
B0028–11
[GND-SHORT]
Side air bag module RH circuit is shorted to ground
B0028–12
[VB-SHORT]
Side air bag module RH circuit is shorted to power supply circuit
B0028–13
[OPEN]
Side air bag module RH circuit is open
B0028–1A
[SHORT]
Side air bag module RH circuits are shorted to each other
B0028 SIDE AIR BAG MODULE
SRC-51
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector for disconnection, looseness or damage.
Is the inspection result normal?
YES
>> GO TO 2.
NO–1 >> Damage: Replace malfunctioning harness and connector.
NO–2 >> Disconnection or looseness: Securely lock the connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace malfunctioning harness and connector.
3.
REPLACE SIDE AIR BAG MODULE RH
1. Replace side air bag module RH. Refer to
SE-21, "Removal and Installation"
.
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to
SR-29, "Removal and Installation"
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
SRC-52
< DTC/CIRCUIT DIAGNOSIS >
B0029 CURTAIN AIR BAG MODULE
B0029 CURTAIN AIR BAG MODULE
DTC Description
INFOID:0000000012199604
DTC DETECTION LOGIC
POSSIBLE CAUSE
[B0029–09, B0029–1A]
• Connection malfunction or short circuit of harness and connector
• Internal malfunction of curtain air bag module RH
• Internal malfunction of air bag diagnosis sensor unit
[B0029–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of curtain air bag module RH
• Internal malfunction of air bag diagnosis sensor unit
[B0029–12]
• Connection malfunction or short circuit to power supply of harness and connector
• Internal malfunction of curtain air bag module RH
• Internal malfunction of air bag diagnosis sensor unit
[B0029–13]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of curtain air bag module RH
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to
SRC-10, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
.
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012199605
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B0029–09
CURTAIN A/B MODULE RH
[Right Curtain Deployment
Control 1 (Subfault)]
[SHORT]
Curtain air bag module RH circuits are shorted to each other
B0029–11
[GND-SHORT]
Curtain air bag module RH circuit is shorted to ground
B0029–12
[VB-SHORT]
Curtain air bag module RH circuit is shorted to power supply circuit
B0029–13
[OPEN]
Curtain air bag module RH circuit is open
B0029–1A
[SHORT]
Curtain air bag module RH circuits are shorted to each other
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст