Nissan Juke F15. Manual — part 511
P0112, P0113 IAT SENSOR 1
EC-857
< DTC/CIRCUIT DIAGNOSIS >
[MR EXCEPT FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
4. Also check harness for short to ground.
Is the inspection result normal?
YES
>> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
3.
CHECK INTAKE AIR TEMPERATURE SENSOR 1 GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between mass air flow sensor harness connector and ECM harness connector.
4. Also check harness for short to power.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.
CHECK INTAKE AIR TEMPERATURE SENSOR 1
Check the intake air temperature sensor 1. Refer to
EC-857, "Component Inspection"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Replace mass air flow sensor (with intake air temperature sensor 1). Refer to
.
Component Inspection
INFOID:0000000012198362
1.
CHECK INTAKE AIR TEMPERATURE SENSOR 1
1. Turn ignition switch OFF.
2. Disconnect mass air flow sensor harness connector.
3. Check resistance between mass air flow sensor terminals as per the following.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace mass air flow sensor (with intake air temperature sensor 1). Refer to
.
+
−
Continuity
MAF sensor
ECM
Connector
Terminal
Connector
Terminal
F8
4
F23
36
Existed
+
−
Continuity
MAF sensor
ECM
Connector
Terminal
Connector
Terminal
F8
3
F23
42
Existed
Mass air flow sensor
Condition
Resistance (k
Ω)
+
−
Terminals
3
4
Intake air temperature [
°C (°F)]
25 (77)
1.800 - 2.200
EC-858
< DTC/CIRCUIT DIAGNOSIS >
[MR EXCEPT FOR NISMO RS MODELS]
P0116 ENGINE COOLANT TEMPERATURE SENSOR 1
P0116 ENGINE COOLANT TEMPERATURE SENSOR 1
DTC Logic
INFOID:0000000012198363
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
INSPECTION START
Is it necessary to erase permanent DTC?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
PERFORM COMPONENT FUNCTION CHECK
Perform component function check. Refer to
EC-859, "Component Function Check"
NOTE:
Use the component function check to check the overall function of the ECT sensor circuit. During this check, a
1st trip DTC might not be confirmed.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
.
3.
PRECONDITIONING
If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following proce-
dure before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
• Before performing the following procedure, do not add fuel.
• Before performing the following procedure, check that fuel level is between 1/4 and 4/4.
• Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.
>> GO TO 4.
4.
PERFORM DTC CONFIRMATION PROCEDURE
1. Move the vehicle to a cool place.
NOTE:
Cool the vehicle in an environment of ambient air temperature between
−10°C (14°F) and 35°C (95°F).
2. Turn ignition switch OFF and leave the vehicle for 12 hours.
CAUTION:
Never turn ignition switch ON during this procedure.
NOTE:
The vehicle must be cooled with the hood open.
3. Start engine and let it idle for 20 minutes or more.
CAUTION:
Never turn ignition switch OFF during idling.
4. Check 1st trip DTC.
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
Possible cause
P0116
ECT SEN/CIRC
(Engine coolant temperature sen-
sor 1 circuit range/performance)
The comparison result of signals transmitted
to ECM from each temperature sensor (IAT
sensor, ECT sensor, FTT sensor, and EOT
sensor) shows that the voltage signal of the
ECT sensor is higher/lower than that of other
temperature sensors when the engine is start-
ed with its cold state.
• Harness or connectors
(High or low resistance in the ECT
sensor circuit)
• Engine coolant temperature sen-
sor 1
P0116 ENGINE COOLANT TEMPERATURE SENSOR 1
EC-859
< DTC/CIRCUIT DIAGNOSIS >
[MR EXCEPT FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Is 1st trip DTC detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Component Function Check
INFOID:0000000012198364
1.
CHECK ENGINE COOLANT TEMPERATURE (ECT) SENSOR 1
1. Turn ignition switch OFF.
2. Disconnect ECT sensor 1 harness connector.
3. Remove ECT sensor 1. Refer to
.
4. Check resistance between ECT sensor 1 terminals by heating
with hot water as shown in the figure.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
NO
>> Proceed to
.
Diagnosis Procedure
INFOID:0000000012198365
1.
CHECK ENGINE COOLANT TEMPERATURE (ECT) SENSOR 1
Check ECT sensor 1. Refer to
EC-859, "Component Inspection"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Replace ECT sensor 1. Refer to
Component Inspection
INFOID:0000000012198366
1.
CHECK ENGINE COOLANT TEMPERATURE SENSOR 1
1. Turn ignition switch OFF.
2. Disconnect engine coolant temperature sensor 1 harness connector.
3. Remove engine coolant temperature sensor 1. Refer to
.
4. Check resistance between engine coolant temperature sensor 1
terminals as per the following.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace engine coolant temperature sensor 1. Refer to
Terminals
Condition
Resistance (k
Ω)
1 and 2
Temperature [
°C (°F)]
20 (68)
2.37 – 2.63
50 (122)
0.68 – 1.00
90 (194)
0.236 – 0.260
JMBIA0080ZZ
ECT sensor
Condition
Resistance
(k
Ω)
+
−
Terminal
1
2
Temperature [
°C (°F)]
20 (68)
2.37 - 2.63
50 (122)
0.68 - 1.00
90 (194)
0.236 - 0.260
JMBIA0080ZZ
EC-860
< DTC/CIRCUIT DIAGNOSIS >
[MR EXCEPT FOR NISMO RS MODELS]
P0117, P0118 ENGINE COOLANT TEMPERATURE SENSOR 1
P0117, P0118 ENGINE COOLANT TEMPERATURE SENSOR 1
DTC Logic
INFOID:0000000012198367
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON and wait at least 5 seconds.
2. Check DTC.
Is DTC detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012198368
1.
CHECK ENGINE COOLANT TEMPERATURE SENSOR 1 POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect engine coolant temperature (ECT) sensor 1 harness connector.
3. Turn ignition switch ON.
4. Check the voltage between ECT sensor 1 harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK ENGINE COOLANT TEMPERATURE SENSOR 1 GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between ECT sensor 1 harness connector and ECM harness connector.
DTC No.
Trouble diagnosis name
(Trouble diagnosis content)
DTC detecting condition
Possible Cause
P0117
ECT SEN/CIRC
(Engine coolant temperature
sensor 1 circuit low input)
An excessively low voltage from the engine
coolant temperature sensor 1 is sent to
ECM.
• Harness or connectors
(Engine coolant temperature sensor 1
circuit is open or shorted.)
• Engine coolant temperature sensor 1
P0118
ECT SEN/CIRC
(Engine coolant temperature
sensor 1 circuit high input)
An excessively high voltage from the en-
gine coolant temperature sensor 1 is sent to
ECM.
+
−
Voltage
(Approx.)
ECT sensor 1
Connector
Terminal
F50
1
Ground
5 V
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст