Nissan Juke F15. Manual — part 907
INT-32
< REMOVAL AND INSTALLATION >
HEADLINING
1. Disengage front roof finisher fixing pawls with a remover
tool (A).
2. Disconnect harness connector, and then remove front roof
finisher.
12. Remove front seat assembly (passenger). Refer to
SE-21, "Removal and Installation"
.
13. Remove sun visor holder (LH and RH)
Rotate 90
°. Remove toward vehicle lower.
14. Remove headlining clips.
15. Remove headlining assembly through the back door.
CAUTION:
• Two workers are required for removal in order to prevent
damage.
• Apply protective tape to the portion where contact may
occur during work.
• Never bend headlining when removing.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• When installing headlining, start by installing both sun visor holders and headlining clips in order to
keep the headlining in position.
• Never bend headlining when installing.
• Be careful that the surface is not wrinkled when installing.
• Align sunroof welt connection (A) to (B) when installing sun-
roof welt.
: Pawl
JMJIA4751ZZ
JMJIA4401ZZ
JMJIA4402ZZ
: Vehicle front
JMJIA4708ZZ
LUGGAGE FLOOR TRIM
INT-33
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
LUGGAGE FLOOR TRIM
Exploded View
INFOID:0000000012199185
2WD models
JMJIA4714ZZ
1.
Rear pillar cap RH
2.
Luggage side upper finisher RH
3.
Luggage side lower finisher RH
4.
Luggage floor board
5.
Luggage side upper finisher LH
6.
Rear pillar cap LH
7.
Seat belt hook LH
(Models with woofer)
8.
Luggage side lower finisher LH
(Models with woofer)
9.
Shock absorber mask LH
(Models with woofer)
10. Luggage floor rear center spacer
(Models with spare tire)
11. Spare tire clamp
(Models with spare tire)
12. Repair kit holder
(Models without spare tire)
13. Luggage rear plate
14. Luggage side lower finisher grille RH 15. Luggage room lamp
16. Shock absorber mask RH
17. Seat belt hook RH
18. Luggage floor box
19. Seat belt hook LH
20. Luggage side lower finisher LH
21. Shock absorber mask LH
22. Luggage side lower finisher grille LH
: Clip
: Pawl
INT-34
< REMOVAL AND INSTALLATION >
LUGGAGE FLOOR TRIM
AWD models
: Metal clip
: Vehicle front
JMJIA4715ZZ
1.
Rear pillar cap RH
2.
Luggage side upper finisher RH
3.
Luggage side lower finisher RH
4.
Luggage floor board
5.
Luggage side upper finisher LH
6.
Rear pillar cap LH
7.
Seat belt hook LH
(Models with woofer)
8.
Luggage side lower finisher LH
(Models with woofer)
9.
Shock absorber mask LH
(Models with woofer)
10. Luggage rear plate
11. Luggage side lower finisher grille RH 12. Luggage room lamp
13. Shock absorber mask RH
14. Seat belt hook RH
15. Seat belt hook LH
16. Luggage side lower finisher LH
17. Shock absorber mask LH
18. Luggage side lower finisher grille LH
19. Luggage floor rear spacer LH
20. Spare tire clamp
21. Luggage floor rear spacer RH
: Clip
: Pawl
: Metal clip
: Vehicle front
LUGGAGE FLOOR TRIM
INT-35
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
LUGGAGE REAR PLATE
LUGGAGE REAR PLATE : Removal and Installation
INFOID:0000000012199186
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
REMOVE
1. Remove back door weather-strip. Refer to
DLK-152, "BACK DOOR WEATHER-STRIP : Removal and
(with Intelligent Key System).
2. Disengage luggage rear plate fixing metal clip with a remover
tool (A), and then remove luggage rear plate.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
When installing luggage rear plate, check that metal clips are securely in body panel holes, and press
them in.
LUGGAGE SIDE LOWER FINISHER
LUGGAGE SIDE LOWER FINISHER : Removal and Installation
INFOID:0000000012199187
REMOVAL
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
1. Remove luggage room lamp. Refer to
INL-49, "Removal and Installation"
2. Remove luggage floor board.
3. Remove luggage floor box (Models with 2WD).
4. Remove luggage rear plate. Refer to
INT-35, "LUGGAGE REAR PLATE : Removal and Installation"
5. Remove rear body side welt. Refer to
INT-21, "BODY SIDE WELT : Removal and Installation"
6. Remove rear seat cushion. Refer to
SE-32, "SEAT CUSHION : Removal and Installation"
.
7. Remove rear seat back. Refer to
SE-33, "SEATBACK : Removal and Installation"
.
8. Remove side hinge of seatback hinge. Refer to
SE-38, "SEATBACK HINGE : Removal and Installation"
9. Disengage luggage side lower finisher fixing clips with a
remover tool (A), and then remove luggage side lower finisher.
INSTALLATION
Note the following item, and install in the reverse order of removal.
: Metal clip
JMJIA4404ZZ
: Clip
JMJIA4405ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст