Nissan Primera P12. Manual — part 98
MULTI-REMOTE CONTROL SYSTEM
BL-101
C
D
E
F
G
H
J
K
L
M
A
B
BL
Key Switch Check
EIS005I1
1.
CHECK KEY SWITCH INPUT SIGNAL
WITH CONSULT-II
Check key switch signal (“KEY IN DETECT”) in “DATA MONITOR”
mode with CONSULT-II.
WITHOUT CONSULT-II
Check voltage between smart entrance control unit harness connector M41 terminal 5 and ground.
OK or NG
OK
>> Key switch is OK.
NG
>> GO TO 2.
2.
CHECK KEY SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect key switch connector.
3.
Check continuity between key switch terminal 1 and 2.
OK or NG
OK
>> Check the following.
●
10A fuse [No. 12, located in fuse block (J/B)]
●
Harness for open or short between key switch and
fuse
●
Harness for open or short between smart entrance control unit and key switch
NG
>> Replace key switch.
Hazard Reminder Check
EIS005I2
1.
CHECK HAZARD WARNING LAMP
Check if hazard warning lamp flashes with hazard switch.
Does hazard warning lamp operate?
Yes
>> GO TO 2.
No
>> Check hazard warning lamp circuit.
KEY IN DETECT
Key is inserted in ignition cylinder
: ON
Key is removed from ignition key cylinder
: OFF
MKIB0200E
Connector
Terminals (wire color)
Condition
(Door lock/
unlock switch)
Voltage (V)
(Approx.)
(+)
(
−
)
M41
5 (B/R)
Ground
Key is
inserted
Battery voltage
Key is
removed
0
MKIB0585E
Terminal
Condition
Continuity
1
2
Key is inserted
Yes
Key is removed
Yes
MKIB0586E
BL-102
MULTI-REMOTE CONTROL SYSTEM
2.
CHECK HAZARD REMINDER OPERATION
Check voltage between smart entrance control unit harness connector and ground.
OK or NG
OK
>> Check harness for open or short between smart entrance control unit and hazard switch.
NG
>> Replace smart entrance control unit.
Connector
Terminals (wire color)
Remote con-
troller
Voltage (V)
(Approx.)
(+)
(
−
)
M43
63 (G/Y)
Ground
Lock
0
→
Battery voltage
→
0
Unlock
0
→
Battery voltage
→
0
→
Battery voltage
→
0
64 (G/B)
Lock
0
→
Battery voltage
→
0
Unlock
0
→
Battery voltage
→
0
→
Battery voltage
→
0
MIIB0473E
MULTI-REMOTE CONTROL SYSTEM
BL-103
C
D
E
F
G
H
J
K
L
M
A
B
BL
ID Code Entry Procedure
EIS005I3
REMOTE CONTROLLER ID SET UP WITH CONSULT-II
NOTE:
If a remote controller is lost, the ID code of the lost remote controller must be erased to prevent unau-
thorized use. When the ID code of a lost remote controller is not known, all controller ID codes should
be erased. After all ID codes are erased, the ID codes of all remaining and/or new remote controllers
must be re-registered.
1.
Turn ignition switch “OFF”.
2.
Connect “CONSULT-II” to the data link connector.
3.
Turn ignition switch “ON”.
4.
Touch “START”.
5.
Touch “SMART ENTRANCE”.
6.
Touch “KEYLESS ENTRY”.
SIIA1645E
PBR455D
SEL845W
SEL846W
BL-104
MULTI-REMOTE CONTROL SYSTEM
7.
Touch “WORK SUPPORT”.
8.
The items are shown on the figure at left can be set up.
●
“KEYLESS CHECK”
Use this mode to confirm if a remote controller ID code is reg-
istered or not.
●
“KEYLESS REGISTRATION”
Use this mode to register a remote controller ID code.
NOTE:
Register the ID code when remote controller or smart
entrance control unit is replaced, or when additional remote
controller is required.
●
“KEYLESS DI FLASH”
This mode can be setting remote controller function.
SEL274W
SIIA1681E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст