Nissan Primera P12. Manual — part 118
BRAKE PIPING AND HOSE
BR-11
C
D
E
G
H
I
J
K
L
M
A
B
BR
BRAKE PIPING AND HOSE
PFP:46210
Hydraulic Piping
EFS002UX
Removal and Installation of Front Brake Piping and Brake Hose
EFS002UY
REMOVAL
CAUTION:
●
Do not allow brake fluid to spill or splash on painted surfaces. Brake fluid can seriously damage
paint. If it gets on a painted surface, wipe it off immediately and wash with water.
●
Do not bend or twist the brake hose sharply, or strongly pull it.
●
Cover brake fluid line connections to prevent dust and other foreign material from entering.
1.
Connect a vinyl tube to the air bleeder.
2.
Drain brake fluid gradually from the air bleeder of each wheel while depressing the brake pedal.
3.
Using a flare nut wrench, remove brake tube flare nuts and dis-
connect brake tube from the brake hose.
4.
Remove union bolts and disconnect caliper assembly from the
brake hose.
5.
First remove lock spring from brake tube and strut mounting
positions. Then remove brake hose.
INSTALLATION
CAUTION:
●
Refill with new brake fluid “DOT 3” or “DOT4”.
●
Never reuse drained brake fluid.
1.
Connect brake hose to caliper assembly and tighten union bolts to the specified torque.
CAUTION:
●
Securely connect brake hose to the protrusions on the cylinder body.
●
Do not reuse the copper washer for union bolts.
2.
Connect brake hose to the strut and fix with lock spring.
3.
Connect brake hose to brake tube. Temporarily tighten flare nuts by hand as far as they will go. Secure
them with the lock spring.
4.
Using a flare nut torque wrench, tighten to the specified torque.
SFIA0465E
SFIA0475E
BR-12
BRAKE PIPING AND HOSE
5.
Refill brake fluid until new brake fluid comes out of each air bleeder.
6.
Afterwards, bleed air.
Removal and Installation of Rear Brake Piping and Brake Hose
EFS002UZ
REMOVAL
CAUTION:
●
Do not allow brake fluid to spill or splash on painted surfaces. Brake fluid can seriously damage
paint. If it gets on a painted surface, wipe it off immediately and wash with water.
●
Do not bend or twist the brake hose sharply, or strongly pull it.
●
Cover brake fluid line connections to prevent dust and other foreign material from entering.
1.
Connect a vinyl tube to the air bleeder.
2.
Drain brake fluid gradually from the air bleeder of each wheel while depressing the brake pedal.
3.
Using a flare nut wrench, remove brake tube flare nuts and dis-
connect brake tube from the brake hose.
4.
Remove lock spring and union bolts.
INSTALLATION
CAUTION:
●
Refill with new brake fluid “DOT 3” or “DOT 4”.
●
Never reuse drained brake fluid.
1.
Connect brake hose to the brake tube. Temporarily tighten flare nut by hand as far as it will go.
2.
Secure brake hose with lock spring and connect wheel-side hose to the caliper assembly.
3.
Tighten union bolts to the specified torque. Then, tighten flare nut to the specified torque with a flare nut
torque wrench.
4.
Refill brake fluid until new brake fluid comes out of each air
bleeder.
5.
Afterwards, bleed air.
Inspection
EFS002V0
CAUTION:
If any connection leaks, retighten it. Replace any damaged parts.
1.
Check hose, tube, and connections for fluid leaks, damage, twist, deformation, contact with other parts,
and loose connections.
: 14.8 - 17.6 N·m (1.5 - 1.7 kg-m,11 - 12 ft-lb)
SFIA0476E
Flare nut
: 14.8 - 17.6 N·m (1.5 - 1.7 kg-m, 11 - 12 ft-lb)
Union bolt
: 16.7- 19.6 N·m (1.7 - 1.9 kg·m, 13 - 14 ft·lb)
SBR686C
BRAKE PIPING AND HOSE
BR-13
C
D
E
G
H
I
J
K
L
M
A
B
BR
2.
Run the engine. Depress brake pedal and hold it for approximately 5 seconds while checking each part for
leaks.
BR-14
BRAKE MASTER CYLINDER
BRAKE MASTER CYLINDER
PFP:46010
Components
EFS002V1
Removal and Installation
EFS002V2
REMOVAL
CAUTION:
Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is
splashed on painted areas, wash it away with water immediately.
1.
Drain brake fluid.
2.
Remove fluid level sensor harness connector.
3.
Using a flare nut wrench, disconnect master cylinder assembly and brake tube.
4.
First remove master cylinder assembly mounting nuts. Then remove master cylinder assembly.
INSTALLATION
1.
Connect brake tube to master cylinder assembly and temporarily tighten flare nut by hand.
2.
Connect master cylinder assembly to brake booster assembly and tighten mounting nuts to the specified
torque.
MFIA0001E
1.
Cap
2.
Strainer
3.
Reservoir tank
4.
Grommet
5.
Piston stopper
6.
Pin
7.
Secondary piston
8.
Primary piston assembly
9.
Stopper cap
10. O-ring
11.
Secondary piston assembly
12. Primary piston assembly
13. Plate
14. Guide assembly
15. Plate
16. Snap ring
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст