Nissan Primera P12. Manual — part 703
WT-26
TROUBLE DIAGNOSIS FOR SYMPTOMS
2.
CHECK CIRCUIT
●
Ignition switch is turned “ON”.
●
Check voltage between tyre pressure monitoring control unit
connector M96 terminal 15 and ground.
Does battery voltage exist?
YES
>> Check display.
NO
>> GO TO 3.
3.
CHECK CONTROL UNIT INPUT SIGNAL
●
Ignition switch is turned “ON”.
●
Check voltage between tyre pressure monitoring control unit
terminal No. 5 or No. 7 and ground.
Inspection results OK?
OK
>> Check combination meter.
NG
>> Replace harness connector between tyre pressure mon-
itoring control unit and display.
Inspection 4: ID Registration Can Not Be Completed
EES001AR
DIAGNOSTIC PROCEDURE
1.
ID REGISTRATION (ALL)
●
Carry out ID registration of all tyre pressure monitoring sensor.
●
Can ID registration of all tyre pressure monitoring sensor be completed?
YES or NO?
YES
>> INSPECTION END.
NO
>> Go To Inspection 1: Tyre Pressure Monitoring Antenna in TROUBLE DIAGNOSIS FOR SELF-
DIAGNOSTIC ITEMS.
15- Ground
: Battery voltage
MDIA0026E
5, 7 -
Ground
: 0V (Min.) and 5V (Max.) are alternately
repeated
MDIA0027E
REMOVAL AND INSTALLATION
WT-27
C
D
F
G
H
I
J
K
L
M
A
B
WT
REMOVAL AND INSTALLATION
PFP:00000
Tyre Pressure Monitoring Sensor
EES001AS
REMOVAL
1.
Deflate tire. Unscrew transmitter retaining nut and allow transmitter to fall into tyre.
2.
Gently bounce tyre so that transmitter falls to bottom of tire.
Place on tyre changing machine and break both tire beads
ensuring that the transmitter remains at the bottom of the tyre.
3.
Turn tyre so that valve hole is at bottom and bounce so that tyre
pressure monitoring sensor is near valve hole. Carefully lift tyre
onto turntable and position valve hole (and transmitter) 270
degree from mounting/dismounting head.
4.
Lubricate tyre well and remove first side of the tyre. Reach
inside the tyre and remove the tyre pressure monitoring sensor.
Remove second side of tyre.
INSTALLATION
1.
Put first side of tyre onto rim.
2.
Mount tyre pressure monitoring sensor on rim and tighten nut.
MDIA0028E
MDIA0029E
MDIA0030E
MEIA0045E
WT-28
REMOVAL AND INSTALLATION
3.
Place wheel on turntable of tyre machine. Ensure that tyre pres-
sure monitoring sensor is 270 degree from mounting head when
second side of tyre is fitted.
NOTE:
Do not touch tyre pressure monitoring sensor at mounting head.
4.
Lubricate tyre well and fit second side of tyre as normal. Ensure that tyre does not rotate relative to rim.
5.
Inflate tyre and fit to appropriate wheel position.
MDIA0029E
SERVICE DATA
WT-29
C
D
F
G
H
I
J
K
L
M
A
B
WT
SERVICE DATA
PFP:00030
Road Wheel
EES001AT
Tyre
EES001AU
Unit: kPa (kg/cm
2
, psi)
Kind of wheel
Aluminum
Steel
Deflection limit
Lateral deflection
Less than 0.3 mm
(0.012 in)
Less than 0.5 mm
(0.020 in)
Vertical deflection
Less than 0.3 mm
(0.012 in)
Less than 0.8 mm
(0.031 in)
Allowable quantity of resid-
ual unbalance
Dynamic
(On the ear part)
Less than 10 g (0.35 oz) (per side)
Static (On the ear part)
Less than 20 g (0.70 oz)
Tyre size
Air pressure
Front wheel
Rear wheel
Sedan
Wagon
205/60R16
215/50R17
220 (2.2, 32)
200 (2.0, 29)
220 (2.2, 32)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст