Nissan Primera P12. Manual — part 109
THEFT WARNING SYSTEM
BL-145
C
D
E
F
G
H
J
K
L
M
A
B
BL
2.
CHECK TRUNK ROOM LAMP SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect trunk room lamp switch harness connector.
3.
Check continuity between trunk room lamp switch terminals 1 and 2.
OK or NG
OK
>> Check the following.
●
Trunk room lamp switch ground circuit
●
Harness for open or short between smart entrance
control unit and trunk room lamp switch
NG
>> Replace trunk room lamp switch.
BACK DOOR SWITCH
1.
CHECK BACK DOOR SWITCH INPUT SIGNAL
With CONSULT- II
Check door switch “TRUNK OPEN SWITCH” in “DATA MONITOR” mode with CONSULT- II.
Without CONSULT- II
Check voltage between smart entrance control unit harness connector and ground.
OK or NG
OK
>> Back door switch is OK.
NG
>> GO TO 2
Terminal
Trunk lid condition
Continuity
1
2
Opened
Yes
Closed
No
SIIA1637E
TRUNK OPEN SW
Back door open
: ON
Back door close
: OFF
SIIA1635E
Connector
Terminal (wire color)
Back door
Voltage (V)
(Approx.)
(+)
(–)
M41
16 (G)
Ground
Closed
5
Open
0
SIIA1636E
BL-146
THEFT WARNING SYSTEM
2.
CHECK BACK DOOR SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect back door release actuator connector.
3.
Check continuity between back door release actuator terminals 1 and 2.
OK or NG
OK
>> Check the following.
●
Back door release actuator ground circuit
●
Harness for open or short between smart entrance
control unit and back door release actuator
NG
>> Replace back door release actuator.
Hood Switch Check
EIS005J0
1.
CHECK HOOD SWITCH INPUT SIGNAL
With CONSULT
−
II
Check “HOOD SWITCH” in “DATA MONITOR” mode with CON-
SULT
−
II.
Without CONSULT
−
II
Check voltage between smart entrance control unit harness connector and ground.
OK or NG
OK
>> Hood switch is OK.
NG
>> GO TO 2.
2.
CHECK DOOR SWITCH
Check hood switch and hood fitting condition.
OK or NG
OK
>> GO TO 3.
NG
>> Adjust installation of hood switch.
Terminal
Back door condition
Continuity
1
2
Opened
Yes
Closed
No
MIIB0456E
HOOD SW
Engine hood is open
: HOOD SW ON
Engine hood is closed
: HOOD SW OFF
SIIA1682E
Connector
Terminal (wire color)
Engine hood
Voltage (V)
(Approx.)
(+)
(–)
M41
15 (LG)
Ground
Open
0
Closed
5
SIIA1649E
THEFT WARNING SYSTEM
BL-147
C
D
E
F
G
H
J
K
L
M
A
B
BL
3.
CHECK HOOR SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect hood switch connector.
3.
Check continuity between hood switch terminals.
OK or NG
OK
>> Check the following.
●
Hood switch ground circuit
●
Harness for open or short between hood switch and
smart entrance control unit
NG
>> Replace hood switch.
Key Switch Check
EIS005J1
1.
CHECK KEY SWITCH INPUT SIGNAL
WITH CONSULT-II
Check key switch signal (“KEY IN DETECT”) in “DATA MONITOR”
mode with CONSULT-II.
WITHOUT CONSULT-II
Check voltage between smart entrance control unit harness connector M41 terminal 5 and ground.
OK or NG
OK
>> Key switch is OK.
NG
>> GO TO 2.
Terminals
Condition
Continuity
1
2
Pushed
No
Released
Yes
SIIA1549E
KEY IN DETECT
Key is inserted in ignition cylinder
: ON
Key is removed from ignition key cylinder
: OFF
MKIB0200E
Connector
Terminals (wire color)
Condition
(Door lock/
unlock switch)
Voltage (V)
(Approx.)
(+)
(
−
)
M41
5 (B/R)
Ground
Key is
inserted
Battery voltage
Key is
removed
0
MKIB0585E
BL-148
THEFT WARNING SYSTEM
2.
CHECK KEY SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect key switch connector.
3.
Check continuity between key switch terminal 1 and 2.
OK or NG
OK
>> Check the following.
●
10A fuse [No. 12, located in fuse block (J/B)]
●
Harness for open or short between key switch and
fuse
●
Harness for open or short between smart entrance control unit and key switch
NG
>> Replace key switch.
Vehicle Security Horn Alarm Check
EIS005J2
1.
CHECK VEHICLE SECURITY HORN OPERATION
1.
Turn ignition switch OFF.
2.
Disconnect smart entrance control unit harness connector.
3.
Apply ground to smart entrance control unit harness connector
M42 terminal 27(Y/B).
Does horn operate?
Yes
>> Replace smart entrance control unit.
No
>> GO TO 2.
2.
CHECK VEHICLE SECURITY HORN RELAY POWER SUPPLY
1.
Disconnect vehicle security horn relay connector.
2.
Check voltage between vehicle security horn relay harness con-
nector B43 terminal 2, 5 and ground.
OK or NG
OK
>> Check the following.
●
Harness for open or short between smart entrance
control unit and vehicle security horn relay
●
Harness open or short between vehicle security horn
relay and ground
●
Harness open or short between vehicle security horn relay and vehicle security horn
NG
>> Check harness open or short between vehicle security horn relay and fuse.
Terminal
Condition
Continuity
1
2
Key is inserted
Yes
Key is removed
Yes
MKIB0586E
SIIA1650E
2 - Ground
: Battery voltage
5 - Ground
: Battery voltage
SIIA1651E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст