Nissan Juke (2016 year). Service Repair Manual — part 387
FRONT DRIVE SHAFT
FAX-37
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
• Secure boot band so that dimension (M) meets the speci-
fication as shown in the figure.
12. Check that displacement does not occur when boot is rotated with the joint sub-assembly and shaft fixed.
CAUTION:
• Reinstall them using boot bands when boot installation positions become incorrect.
• Never reuse boot band.
Transaxle Side (Left Drive Shaft)
1. Clean the old grease on housing with paper waste.
2. Install dust shield to housing assembly.
CAUTION:
Never reuse dust shield.
3. Install circular clip to housing assembly.
CAUTION:
Never reuse circular clip.
4. Install dynamic damper, follow the procedure described below.
a. Install dynamic damper to shaft.
b. Secure dynamic damper with bands in the following specified
position (A) when installing.
CAUTION:
Never reuse boot bands.
c. Install boot bands securely as showin in the figure.
5. Install boot and boot bands to housing assembly.
CAUTION:
Dimension (M)
: 1.0 – 4.0 mm (0.039 – 0.157 in)
DSF0047D
A :
JPDIF0178ZZ
PDIA1188J
Revision: November 2015
2016 JUKE
FAX-38
< REMOVAL AND INSTALLATION >
[TYPE 1]
FRONT DRIVE SHAFT
• Wrap serration on housing assembly with tape (A) to pro-
tect the boot from damage.
• Never reuse boot and boot band.
6. Remove the tape wrapped around the serration on shaft.
7. To install the spider assembly (1), align it with the matching
marks (A) on the shaft (2) put during the removal, and direct the
serration mounting surface (B) to the shaft.
8. Secure spider assembly onto shaft with snap ring (1).
CAUTION:
Never reuse snap ring.
9. Apply the appropriate amount of grease to spider assembly and sliding surface.
10. Align matching marks put during the removal of housing assembly.
11. Install stopper ring.
CAUTION:
Never reuse stopper ring.
12. Apply NISSAN genuine grease (refer to parts catalog) to housing assembly.
13. Install the boot securely into grooves (indicated by “*” marks)
shown in the figure.
CAUTION:
If grease adheres to the boot mounting surface (indicated
by “*” marks) on the shaft or housing assembly, boot may
be removed. Remove all grease from the boot mounting
surface.
JPDIF0009ZZ
JPDIF0017ZZ
JPDIF0014ZZ
Grease amount
: Refer to
.
JSDIA2063ZZ
Revision: November 2015
2016 JUKE
FRONT DRIVE SHAFT
FAX-39
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
14. To prevent the deformation of the boot, adjust the boot installation length to the value shown below (L) by
inserting the suitable tool into the inside of boot from the large diameter side of boot and discharging
inside air.
CAUTION:
• If the boot installation length exceeds the standard, it may cause breakage of the boot.
• Be careful not to touch the inside of the boot with the tip of tool.
15. Fix large diameter side and small diameter side of boot with boot band.
a. Set boot band to the drive shaft boot groove and temporarily fix
pawl (A) of boot band to (B) of boot band.
b. Tighten boot band protrusions (B) with boot band crimping tool
(A) [SST:KV40107310 ( — )] in the direction shown by
arrows.
CAUTION:
Securely install boot band (A) to boot band pawl (B).
16. Check that displacement does not occur when boot is rotated with the housing assembly fixed.
CAUTION:
• If displacement occurs, reinstall band.
• Never reuse boot band.
Transaxle Side (Right Drive Shaft)
1. Clean the old grease on housing with paper waste.
2. Install dynamic damper, follow the procedure described below.
a. Install dynamic damper to shaft.
L
: Refer to
JSDIA6965ZZ
JSDIA6966ZZ
JSDIA6968ZZ
Revision: November 2015
2016 JUKE
FAX-40
< REMOVAL AND INSTALLATION >
[TYPE 1]
FRONT DRIVE SHAFT
b. Secure dynamic damper with bands in the following specified
position (A) when installing.
CAUTION:
Never reuse bands.
c.
Install boot bands securely as showin in the figure.
3. Install support bearing, follow the procedure described below.
a. Install dust shield to housing.
CAUTION:
Never reuse dust shield.
b. Press support bearing (1) onto housing to using the suitable tool
(A).
CAUTION:
Never reuse support bearing.
c.
Install snap ring (1).
CAUTION:
Never reuse snap ring.
A
: Refer to
JPDIF0178ZZ
PDIA1188J
JPDIF0056ZZ
JPDIF0106ZZ
Revision: November 2015
2016 JUKE
FRONT DRIVE SHAFT
FAX-41
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
d. Install dust shields.
CAUTION:
Never reuse dust shields.
4. Install boot and boot bands to housing assembly.
CAUTION:
• Wrap serration on housing assembly with tape (A) to pro-
tect the boot from damage.
• Never reuse boot and boot band.
5. Remove the tape wrapped around the serration on shaft.
6. To install the spider assembly (1), align it with the matching
marks (A) on the shaft (2) put during the removal, and direct the
serration mounting surface (B) to the shaft.
7. Secure spider assembly onto shaft with snap ring (1).
CAUTION:
Never reuse snap ring.
8. Apply the appropriate amount of grease to spider assembly and sliding surface.
9. Align matching marks put during the removal of housing assembly.
10. Install stopper ring.
CAUTION:
Never reuse stopper ring.
11. Apply NISSAN genuine grease (refer to parts catalog) to housing assembly.
JPDIF0127ZZ
JPDIF0009ZZ
JPDIF0017ZZ
JPDIF0014ZZ
Revision: November 2015
2016 JUKE
FAX-42
< REMOVAL AND INSTALLATION >
[TYPE 1]
FRONT DRIVE SHAFT
12. Install the boot securely into grooves (indicated by “*” marks) shown in the figure.
a. For NISMO RS models.
CAUTION:
If grease adheres to the boot mounting surface (indicated
by “*” marks) on the shaft or housing assembly, boot may
be removed. Remove all grease from the boot mounting
surface.
b. Except for NISMO RS models.
CAUTION:
If grease adheres to the boot mounting surface (indicated
by “*” marks) on the shaft or housing assembly, boot may
be removed. Remove all grease from the boot mounting
surface.
13. To prevent the deformation of the boot, adjust the boot installation length to the value shown below (L) by
inserting the suitable tool into the inside of boot from the large diameter side of boot and discharging
inside air.
CAUTION:
• If the boot installation length exceeds the standard, it may cause breakage of the boot.
• Be careful not to touch the inside of the boot with the tip of tool.
14. Fix large diameter side and small diameter side of boot with boot band.
a. Set boot band to the drive shaft boot groove and temporarily fix
pawl (A) of boot band to (B) of boot band.
Grease amount
: Refer to
.
JPDIF0224ZZ
JSDIA2063ZZ
L
: Refer to
JSDIA6965ZZ
Revision: November 2015
2016 JUKE
FRONT DRIVE SHAFT
FAX-43
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
b. Tighten boot band protrusions (B) with boot band crimping tool
(A) [SST:KV40107310 ( — )] in the direction shown by
arrows.
CAUTION:
Securely install boot band (A) to boot band pawl (B).
15. Check that displacement does not occur when boot is rotated with the housing assembly fixed.
CAUTION:
• If displacement occurs, reinstall band.
• Never reuse boot band.
2WD : Inspection
INFOID:0000000012201536
INSPECTION AFTER INSTALLATION
1. Check wheel sensor harness for proper connection. Refer to
BRC-147, "FRONT WHEEL SENSOR :
.
2. Check the wheel alignment. Refer to
.
3. Adjust neutral position of steering angle sensor. Refer to
.
AWD
AWD : Exploded View
INFOID:0000000012201537
LEFT SIDE
JSDIA6966ZZ
JSDIA6968ZZ
Revision: November 2015
2016 JUKE
FAX-44
< REMOVAL AND INSTALLATION >
[TYPE 1]
FRONT DRIVE SHAFT
RIGHT SIDE
1.
Circular clip
2.
Dust shield
3.
Housing assembly
4.
Boot band
5.
Boot
6.
Damper band
7.
Dynamic damper
8.
Circular clip
9.
Joint sub-assembly
: Wheel side
: Fill NISSAN Genuine grease or equivalent.
: Always replace after every disassembly.
JSDIA2093ZZ
1.
Joint sub-assembly
2.
Circular clip
3.
Boot band
4.
Boot
5.
Damper band
6.
Dynamic damper
7.
Housing assembly
: Wheel side
: Fill NISSAN Genuine grease or equivalent.
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JSDIA2095GB
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст