Nissan Juke (2016 year). Service Repair Manual — part 444
SYSTEM
INL-9
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
• BCM provides the interior room lamp power supply continuously when the ignition switch position is ON.
NOTE:
Each function of interior room lamp battery saver can be set by CONSULT. Refer to
SAVER : CONSULT Function (BCM - BATTERY SAVER)"
.
ILLUMINATION CONTROL SYSTEM
ILLUMINATION CONTROL SYSTEM : System Diagram
INFOID:0000000012197001
ILLUMINATION CONTROL SYSTEM : System Description
INFOID:0000000012197002
OUTLINE
Each illumination lamp is controlled by each function of BCM and IPDM E/R.
Control by BCM
• Combination switch reading function
• Headlamp control function
Control by IPDM E/R
• Relay control function
Control by combination meter
• Meter illumination control function (Refer to
MWI-11, "SPEEDOMETER : System Description"
ILLUMINATION CONTROL
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits position light request signal to IPDM E/R and combination meter according to tail lamp ON
condition.
Tail lamp ON condition
- Lighting switch 1ST
- Lighting switch 2ND
- Lighting switch AUTO, and the auto light function ON judgment (With auto light system)
• IPDM E/R turns the integrated tail lamp relay ON according to position light request signal. It provides the
power supply to each illumination lamp.
• Combination meter enters in the nighttime mode according to position light request signal. Under the night-
time mode the combination meter controls the illuminance by controlling the each illumination lamp (ground
side).
JMLIA2724GB
Revision: November 2015
2016 JUKE
INL-10
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000012946726
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
NOTE:
*: For models with automatic A/C, this diagnosis mode is not used.
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
×
Air conditioning system
AIR CONDITONER
×
×
*
• Intelligent Key system
• Engine start system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door open
TRUNK
×
Theft warning alarm
THEFT ALM
×
×
×
RAP
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
AIR PRESSURE MONITOR
×
×
×
Revision: November 2015
2016 JUKE
DIAGNOSIS SYSTEM (BCM)
INL-11
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
NOTE:
*: Power position shifts to “LOCK” from “OFF”, when ignition switch is in the OFF position, selector lever is in the P position (A/T models
and CVT models), and any of the following conditions are met.
• Closing door
• Opening door
• Door is locked using door request switch
• Door is locked using Intelligent Key
The power position shifts to “ACC” when the push-button ignition switch (push switch) is pushed at “LOCK”.
INT LAMP
CONSULT screen item
Indication/Unit
Description
Vehicle Speed
km/h
Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter
km
Total mileage (Odometer value) of the moment a particular DTC is detected
Vehicle Condition
SLEEP>LOCK
Power position status of
the moment a particular
DTC is detected
While turning BCM status from low power consumption mode to
normal mode (Power position is “LOCK”*.)
SLEEP>OFF
While turning BCM status from low power consumption mode to
normal mode (Power position is “OFF”.)
LOCK>ACC
While turning power position from “LOCK”* *to “ACC”
ACC>ON
While turning power position from “ACC” to “IGN”
RUN>ACC
While turning power position from “RUN” to “ACC” (Vehicle is
stopping and selector lever is except P position.)
CRANK>RUN
While turning power position from “CRANKING” to “RUN” (From
cranking up the engine to run it)
RUN>URGENT
While turning power position from “RUN“ to “ACC” (Emergency
stop operation)
ACC>OFF
While turning power position from “ACC” to “OFF”
OFF>LOCK
While turning power position from “OFF” to “LOCK”*
OFF>ACC
While turning power position from “OFF” to “ACC”
ON>CRANK
While turning power position from “IGN” to “CRANKING”
OFF>SLEEP
While turning BCM status from normal mode (Power position is
“OFF”.) to low power consumption mode
LOCK>SLEEP
While turning BCM status from normal mode (Power position is
“LOCK”*.) to low power consumption mode
LOCK
Power position is “LOCK”*
OFF
Power position is “OFF” (Ignition switch OFF)
ACC
Power position is “ACC” (Ignition switch ACC)
ON
Power position is “IGN” (Ignition switch ON with engine stopped)
ENGINE RUN
Power position is “RUN” (Ignition switch ON with engine running)
CRANKING
Power position is “CRANKING” (At engine cranking)
IGN Counter
0 - 39
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1
→
2
→
3...38
→
39 after returning to the normal condition
whenever ignition switch OFF
→
ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
Revision: November 2015
2016 JUKE
INL-12
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
INT LAMP : CONSULT Function (BCM - INT LAMP)
INFOID:0000000012197004
WORK SUPPORT
*: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
JPLIA0093GB
Service item
Setting item
Setting
ROOM LAMP TIMER SET
MODE 2
7.5 sec.
Sets the interior room lamp ON time. (Timer operating time)
MODE 3*
15 sec.
MODE 4
30 sec.
SET I/L D-UNLCK INTCON
On*
With the interior room lamp timer function
Off
Without the interior room lamp timer function
ROOM LAMP ON TIME SET
MODE 1
0.5 sec.
Sets the interior room lamp gradual brightening time.
MODE 2*
1 sec.
MODE 3
2 sec.
MODE 4
3 sec.
MODE 5
0 sec.
ROOM LAMP OFF TIME SET
MODE 1
0.5 sec.
Sets the interior room lamp gradual dimming time.
MODE 2*
1 sec.
MODE 3
2 sec.
MODE 4
3 sec.
MODE 5
0 sec.
R LAMP TIMER LOGIC SET
MODE 1*
Interior room lamp timer activates with synchronizing all doors.
MODE 2
Interior room lamp timer activates with synchronizing the driver door
only.
FOG LAMP OVERRIDE
On
With front fog override function
Off*
Without front fog override function
Revision: November 2015
2016 JUKE
DIAGNOSIS SYSTEM (BCM)
INL-13
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
ACTIVE TEST
BATTERY SAVER
BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER)
INFOID:0000000012197005
WORK SUPPORT
Monitor item
[Unit]
Description
REQ SW-DR
[On/Off]
Indicated [On/Off] condition of door request switch (driver side)
REQ SW-AS
[On/Off]
Indicated [On/Off] condition of door request switch (passenger side)
REQ SW-RR
[On/Off]
NOTE:
This item is displayed, but cannot be monitored
REQ SW-RL
[On/Off]
NOTE:
This item is displayed, but cannot be monitored
PUSH SW
[On/Off]
Indicates [On/Off] condition of push-button ignition switch
UNLK SEN -DR
[On/Off]
Indicates [On/Off] condition of driver door UNLOCK status
DOOR SW-DR
[On/Off]
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
[On/Off]
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
[On/Off]
Indicated [On/Off] condition of rear door switch RH
DOOR SW- RL
[On/Off]
Indicated [On/Off] condition of rear door switch LH
DOOR SW- BK
[On/Off]
Indicated [On/Off] condition of back door switch
CDL LOCK SW
[On/Off]
Indicated [On/Off] condition of lock signal from door lock unlock switch
CDL UNLOCK SW
[On/Off]
Indicated [On/Off] condition of unlock signal from door lock unlock switch
TRNK/HAT MNTR
[On/Off]
NOTE:
This item is displayed, but cannot be monitored
KEY CYL LK-SW
[On/Off]
Indicated [On/Off] condition of lock signal from door key cylinder
KEY CYL UN-SW
[On/Off]
Indicated [On/Off] condition of unlock signal from door key cylinder
RKE-LOCK
[On/Off]
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
[On/Off]
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
Test item
Operation
Description
INT LAMP
On
Outputs the interior room lamp control signal.
Off
Stops the interior room lamp control signal.
STEP LAMP TEST
On
NOTE:
This item is indicated, but can not tested
Off
Revision: November 2015
2016 JUKE
INL-14
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
*:Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Service item
Setting item
Setting
ROOM LAMP TIMER SET
MODE 1
30 min.
Sets the interior room lamp battery saver timer operating
time.
NOTE:
The factor setting is 10 minutes. The setting cannot be re-
turned to the factory setting, when the setting is changed
once.
MODE 2
60 min.
MODE 3
15 min.
BATTERY SAVER SET
On
*
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
IGN BATTERY SAVER SET
MODE 1
Without
Sets the ignition battery saver timer operating time.
MODE 2
30 min.
MODE 3*
10 min.
MODE 4
5 min.
MODE 5
60 min.
ACC BATTERY SAVER SET
MODE 1
Without
Sets the accessory battery saver timer operating time.
MODE 2*
30 min.
MODE 3
10 min.
MODE 4
5 min.
MODE 5
60 min.
Monitor item
[Unit]
Description
REQ SW-DR
[On/Off]
Indicated [On/Off] condition of door request switch (driver side)
REQ SW-AS
[On/Off]
Indicated [On/Off] condition of door request switch (passenger side)
REQ SW-RR
[On/Off]
NOTE:
This item is displayed, but cannot be monitored
REQ SW-RL
[On/Off]
NOTE:
This item is displayed, but cannot be monitored
PUSH SW
[On/Off]
Indicates [On/Off] condition of push-button ignition switch
UNLK SEN -DR
[On/Off]
Indicates [On/Off] condition of driver door UNLOCK status
DOOR SW-DR
[On/Off]
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
[On/Off]
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
[On/Off]
Indicated [On/Off] condition of rear door switch RH
DOOR SW- RL
[On/Off]
Indicated [On/Off] condition of rear door switch LH
DOOR SW- BK
[On/Off]
Indicated [On/Off] condition of back door switch
CDL LOCK SW
[On/Off]
Indicated [On/Off] condition of lock signal from door lock unlock switch
Revision: November 2015
2016 JUKE
DIAGNOSIS SYSTEM (BCM)
INL-15
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
ACTIVE TEST
CDL UNLOCK SW
[On/Off]
Indicated [On/Off] condition of unlock signal from door lock unlock switch
TRNK/HAT MNTR
[On/Off]
NOTE:
This item is displayed, but cannot be monitored
KEY CYL LK-SW
[On/Off]
Indicated [On/Off] condition of lock signal from door key cylinder
KEY CYL UN-SW
[On/Off]
Indicated [On/Off] condition of unlock signal from door key cylinder
RKE-LOCK
[On/Off]
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
[On/Off]
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
Monitor item
[Unit]
Description
Test item
Operation
Description
BATTERY SAVER
Off
Cuts the interior room lamp power supply.
On
Outputs the interior room lamp power supply.
Revision: November 2015
2016 JUKE
INL-16
< ECU DIAGNOSIS INFORMATION >
BCM
ECU DIAGNOSIS INFORMATION
BCM
List of ECU Reference
INFOID:0000000012197006
ECU
Reference
BCM
BCS-61, "DTC Inspection Priority Chart"
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст