Nissan Juke (2016 year). Service Repair Manual — part 443
INL-1
DRIVER CONTROLS
C
D
E
F
G
H
I
J
K
M
SECTION
INL
A
B
INL
N
O
P
CONTENTS
INTERIOR LIGHTING SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Procedure without Cowl Top Cover
. ..
Precautions For Xenon Headlamp Service . . . ...
Precautions for Removing Battery Terminal . . .....
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
INTERIOR LIGHTING SYSTEM . . . . . . . . ..
INTERIOR LIGHTING SYSTEM : Component
Parts Location . . . . . . . . . . . . . . ...
INTERIOR LIGHTING SYSTEM :
Component Description . . . . . . . . . . ....
SYSTEM . . . . . . . . . . . . . . . ..
INTERIOR ROOM LAMP CONTROL SYSTEM . . ..
INTERIOR ROOM LAMP CONTROL SYSTEM :
System Diagram . . . . . . . . . . . . . ....
INTERIOR ROOM LAMP CONTROL SYSTEM :
System Description . . . . . . . . . . . . ...
INTERIOR ROOM LAMP BATTERY SAVER SYS-
TEM . . . . . . . . . . . . . . . . . . . ..
INTERIOR ROOM LAMP BATTERY SAVER
SYSTEM : System Diagram . . . . . . . . . ..
INTERIOR ROOM LAMP BATTERY SAVER
SYSTEM : System Description . . . . . . . .....
ILLUMINATION CONTROL SYSTEM . . . . . .....
ILLUMINATION CONTROL SYSTEM : System
Diagram . . . . . . . . . . . . . . . . .....
ILLUMINATION CONTROL SYSTEM : System
Description . . . . . . . . . . . . . . . ....
DIAGNOSIS SYSTEM (BCM) . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . .
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . .
INT LAMP . . . . . . . . . . . . . . . . ...
INT LAMP : CONSULT Function (BCM - INT
LAMP) . . . . . . . . . . . . . . . . . ..
BATTERY SAVER . . . . . . . . . . . . . .
BATTERY SAVER : CONSULT Function (BCM -
BATTERY SAVER) . . . . . . . . . . . . ..
ECU DIAGNOSIS INFORMATION . . . ..
BCM . . . . . . . . . . . . . . . . ...
List of ECU Reference . . . . . . . . . . . .
WIRING DIAGRAM . . . . . . . . . ..
INTERIOR ROOM LAMP CONTROL SYSTEM
...
Wiring Diagram . . . . . . . . . . . . . .
ILLUMINATION . . . . . . . . . . . . .
Wiring Diagram . . . . . . . . . . . . . .
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORK FLOW . ...
Work Flow . . . . . . . . . . . . . . . .
DTC/CIRCUIT DIAGNOSIS . . . . . . .
INTERIOR ROOM LAMP POWER SUPPLY
CIRCUIT . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . ...
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
INTERIOR ROOM LAMP CONTROL CIRCUIT
...
Description . . . . . . . . . . . . . . . ...
Component Function Check . . . . . . . . .
Revision: November 2015
2016 JUKE
INL-2
Diagnosis Procedure . . . . . . . . . . . ..
LUGGAGE ROOM LAMP CIRCUIT . . . . ..
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ..
PUSH-BUTTON IGNITION SWITCH ILLUMI-
NATION CIRCUIT . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ..
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . .
INTERIOR LIGHTING SYSTEM SYMPTOMS ...
Symptom Table . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . ...
MAP LAMP . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . . .
Replacement . . . . . . . . . . . . . . ...
GLOVE BOX LAMP . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Replacement . . . . . . . . . . . . . . ...
LUGGAGE ROOM LAMP . . . . . . . . ..
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Replacement . . . . . . . . . . . . . . ...
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Bulb Specifications . . . . . . . . . . . . ..
Revision: November 2015
2016 JUKE
PRECAUTIONS
INL-3
< PRECAUTION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000012196993
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, it is recommended that all maintenance
and repair be performed by an authorized NISSAN/INFINITI dealer.
• Improper repair, including incorrect removal and installation of the SRS, can lead to personal injury
caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module,
see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery or batteries, and wait at least 3 minutes before performing any service.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000012964910
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
Precautions For Xenon Headlamp Service
INFOID:0000000012964911
WARNING:
Comply with the following warnings to prevent any serious accident.
• Disconnect the battery cable (negative terminal) or the power supply fuse before installing, remov-
ing, or touching the xenon headlamp (bulb included). The xenon headlamp contains high-voltage
generated parts.
• Never work with wet hands.
• Check the xenon headlamp ON-OFF status after assembling it to the vehicle. Never turn the xenon
headlamp ON in other conditions. Connect the power supply to the vehicle-side connector.
PIIB3706J
Revision: November 2015
2016 JUKE
INL-4
< PRECAUTION >
PRECAUTIONS
(Turning it ON outside the lamp case may cause fire or visual impairments.)
• Never touch the bulb glass immediately after turning it OFF. It is extremely hot.
CAUTION:
Comply with the following cautions to prevent any error and malfunction.
• Install the xenon bulb securely. (Insufficient bulb socket installation may melt the bulb, the connec-
tor, the housing, etc. by high-voltage leakage or corona discharge.)
• Never perform HID circuit inspection with a tester.
• Never touch the xenon bulb glass with hands. Never put oil and grease on it.
• Dispose of the used xenon bulb after packing it in thick vinyl without breaking it.
• Never wipe out dirt and contamination with organic solvent (thinner, gasoline, etc.).
Precautions for Removing Battery Terminal
INFOID:0000000012964912
When disconnecting the battery terminal, pay attention to the following.
• Always use a 12V battery as power source.
• Never disconnect battery terminal while engine is running.
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
• For vehicles with the engine listed below, remove the battery termi-
nal after a lapse of the specified time:
NOTE:
ECU may be active for several tens of seconds after the ignition switch is turned OFF. If the battery terminal
is removed before ECU stops, then a DTC detection error or ECU data corruption may occur.
• After high-load driving, if the vehicle is equipped with the V9X engine, turn the ignition switch OFF and wait
for at least 15 minutes to remove the battery terminal.
NOTE:
• Turbocharger cooling pump may operate in a few minutes after the ignition switch is turned OFF.
• Example of high-load driving
- Driving for 30 minutes or more at 140 km/h (86 MPH) or more.
- Driving for 30 minutes or more on a steep slope.
• For vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON
the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of main battery and sub battery discon-
nected, then DTC may be detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
D4D engine
: 20 minutes
YS23DDT
: 4 minutes
HRA2DDT
: 12 minutes
YS23DDTT
: 4 minutes
K9K engine
: 4 minutes
ZD30DDTi
: 60 seconds
M9R engine
: 4 minutes
ZD30DDTT
: 60 seconds
R9M engine
: 4 minutes
V9X engine
: 4 minutes
YD25DDTi
: 2 minutes
SEF289H
Revision: November 2015
2016 JUKE
COMPONENT PARTS
INL-5
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
SYSTEM DESCRIPTION
COMPONENT PARTS
INTERIOR LIGHTING SYSTEM
INTERIOR LIGHTING SYSTEM : Component Parts Location
INFOID:0000000012196995
INTERIOR LIGHTING SYSTEM : Component Description
INFOID:0000000012196996
1.
2.
BCM
Refer to
SYSTEM : Component Parts Loca-
tion"
3.
Door lock and unlock switch
4.
Front door request switch (driver
side)
5.
Front door lock assembly (driver
side) (unlock sensor)
6.
Door switch
7.
Luggage room lamp
8.
Back door switch
9.
Door key cylinder switch
10. Remote keyless entry receiver
11. Optical sensor
12. Map lamp
13. Combination meter
14. Push-button ignition switch
JMLIA6149ZZ
Part
Description
BCM
Controls the interior lighting system.
IPDM E/R
Controls the integrated relay according to the request signal from BCM (via CAN com-
munication).
Remote keyless entry receiver
Receives the lock/unlock signal form Keyfob.
Combination switch
(Lighting & turn signal switch)
Refer to
BCS-8, "COMBINATION SWITCH READING SYSTEM : System Description"
.
• Door lock and unlock switch
• Door request switch
Inputs the lock/unlock signal to BCM.
Door switch
Inputs the door switch signal to BCM.
Back door switch
Inputs the back door switch signal to BCM.
Unlock sensor
Detects door lock condition of driver side door.
Optical sensor
Optical sensor converts the outside brightness (lux) to voltage and transmits the optical
sensor signal to BCM.
Revision: November 2015
2016 JUKE
INL-6
< SYSTEM DESCRIPTION >
SYSTEM
SYSTEM
INTERIOR ROOM LAMP CONTROL SYSTEM
INTERIOR ROOM LAMP CONTROL SYSTEM : System Diagram
INFOID:0000000012196997
INTERIOR ROOM LAMP CONTROL SYSTEM : System Description
INFOID:0000000012196998
OUTLINE
• Interior room lamps* are controlled by interior room lamp timer control function of BCM.
*: Map lamp (when map lamp switch is in DOOR position).
• Luggage room lamp is controlled by luggage room lamp control function of BCM.
• Push-button ignition switch illumination is controlled by the push-button ignition switch illumination control
function of BCM.
INTERIOR ROOM LAMP TIMER CONTROL
JMLIA6150GB
Revision: November 2015
2016 JUKE
SYSTEM
INL-7
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
Interior Room Lamp Timer Basic Operation
• The interior room lamp turns ON and OFF (gradual brightening and dimming) by the interior room lamp
timer.
• BCM judges the vehicle condition with the following items. It activates the interior room lamp timer.
- Ignition switch status
- Door switch signal (except back door)
- Door lock/unlock signal (Remote keyless entry receiver, each door request switch, door lock and unlock
switch, key cylinder switch)
NOTE:
Each function of interior room lamp timer can be set by CONSULT. Refer to
.
Interior Room Lamp ON Operation
• BCM always turns the interior room lamp ON when any door opens except back door.
• BCM activates the interior room lamp timer in any of the following conditions to turn the interior room lamp
ON for a period of time.
- Status of all doors except back door changes from open to close
- Ignition switch is turned ON
→
OFF
- Door unlock signal is detected when all doors close except back door with ignition switch OFF
NOTE:
The timer restarts if new condition is input during the timer operating time.
Interior Room Lamp OFF Operation
BCM stops the timer in any of the following conditions to turn the interior room lamp OFF.
• The timer operating time is expired
• Ignition switch is turned OFF
→
ACC/ON
• Door lock signal is detected with all doors close except back door.
LUGGAGE ROOM LAMP CONTROL
BCM turns luggage room lamp ON when the following condition is detected.
• Back door switch is ON
BCM turns luggage room lamp OFF when the following condition is detected.
• Back door switch is OFF
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CONTROL
Push-button Ignition Switch Illumination Basic Operation
BCM provides the power supply to turn the push-button ignition switch illumination ON.
Push-button Ignition Switch Illumination ON Operation
BCM turns the push-button ignition switch illumination ON in the following conditions.
• Ignition switch ON
• Tail lamp ON
• Any of the following conditions with ignition switch OFF/ACC
- Engine start permission is entered
- Driver side door is LOCK
→
UNLOCK
- Driver side door is open
JPLIA0093GB
Revision: November 2015
2016 JUKE
INL-8
< SYSTEM DESCRIPTION >
SYSTEM
Push-button Ignition Switch Illumination OFF Operation
BCM turns the push-button ignition switch illumination OFF in any of the following conditions.
• The push-button ignition switch illumination ON conditions do not satisfy.
• Any of the following conditions with ignition switch OFF.
- The push-button ignition switch illumination ON conditions do not change (15 seconds after the ignition
switch OFF)
- Driver side door is UNLOCK
→
LOCK
INTERIOR ROOM LAMP BATTERY SAVER SYSTEM
INTERIOR ROOM LAMP BATTERY SAVER SYSTEM : System Diagram
INFOID:0000000012196999
INTERIOR ROOM LAMP BATTERY SAVER SYSTEM : System Description
INFOID:0000000012197000
OUTLINE
• Interior room lamp battery saver is controlled by BCM.
• BCM turns applicable lamps OFF depending on the vehicle condition. This function prevents the battery
from over-discharging if the driver neglects turning OFF the lamps.
Applicable lamps
• Map lamp
• Luggage room lamp
INTERIOR ROOM LAMP BATTERY SAVER FUNCTION
• When the ignition switch is turned to other position than ON, BCM operates the timer for a period of time to
cut the interior room lamp power supply.
• BCM restarts the timer when any of the following signals changes while operating the timer.
- Ignition switch status
- Door switch signal (ALL)
- Door lock/unlock signal (remote keyless entry receiver, each door request switch, door lock and unlock
switch, key cylinder switch)
JMLIA6151GB
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст