Nissan Juke (2016 year). Service Repair Manual — part 654
TM-424
< WIRING DIAGRAM >
[CVT: RE0F10D]
CVT SHIFT LOCK SYSTEM
JRDWC6640GB
Revision: November 2015
2016 JUKE
CVT SHIFT LOCK SYSTEM
TM-425
< WIRING DIAGRAM >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
JRDWC6641GB
Revision: November 2015
2016 JUKE
TM-426
< BASIC INSPECTION >
[CVT: RE0F10D]
DIAGNOSIS AND REPAIR WORK FLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow
INFOID:0000000012201121
NOTE:
“DTC” includes DTC at the 1st trip.
1.
OBTAIN INFORMATION ABOUT SYMPTOM
Refer to
TM-427, "Diagnostic Work Sheet"
and interview the customer to obtain the malfunction information
(conditions and environment when the malfunction occurred) as much as possible when the customer brings
in the vehicle.
>> GO TO 2.
2.
CHECK DTC
1. Before checking the malfunction, check whether any DTC exists.
2. If DTC exists, perform the following operations.
-
Records the DTCs. (Print out using CONSULT and affix to the Work Order Sheet.)
-
Erase DTCs.
-
Check the relation between the cause found by DTC and the malfunction information from customer.
can be used effectively.
3. Check the relevant information including STI, etc.
Do malfunction information and DTC exists?
Malfunction information and DTC exists.>>GO TO 3.
Malfunction information exists but no DTC.>>GO TO 4.
No malfunction information, but DTC exists.>>GO TO 5.
3.
REPRODUCE MALFUCTION SYSTEM
Check the malfunction described by the customer on the vehicle.
Check if the behavior is fail safe or normal operation. Refer to
Interview sheet can be used effectively when reproduce malfunction conditions. Refer to
Verify the relationship between the symptom and the conditions in which the malfunction described by the cus-
tomer occurs.
>> GO TO 5.
4.
REPRODUCE MALFUNCTION SYMPTOM
Check the malfunction described by the customer on the vehicle.
Check if the behavior is fail safe or normal operation. Refer to
Interview sheet can be used effectively when reproduce malfunction conditions. Refer to
Verify the relationship between the symptom and the conditions in which the malfunction described by the cus-
tomer occurs.
>> GO TO 6.
5.
PERFORM “DTC CONFIRMATION PROCEDURE”
Perform “DTC CONFIRMATION PROCEDURE” of the appropriate DTC to check if DTC is detected again.
TM-413, "DTC Inspection Priority Chart"
when multiple DTCs are detected, and then determine the
order for performing the diagnosis.
Is any DTC detected?
YES
>> GO TO 7.
NO
>> Follow
GI-45, "Intermittent Incident"
to check.
6.
IDENTIFY MALFUNCTIONING SYSTEM WITH “DIAGNOSIS CHART BY SYMPTOM”
Revision: November 2015
2016 JUKE
DIAGNOSIS AND REPAIR WORK FLOW
TM-427
< BASIC INSPECTION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Use
from the symptom inspection result in step 4. Then identify where to start per-
forming the diagnosis based on possible causes and symptoms.
>> GO TO 8.
7.
REPAIR OR REPLACE THE MALFUNCTIONING PARTS
Repair or replace the detected malfunctioning parts.
Reconnect parts or connector after repairing or replacing, and then erase DTC if necessary.
>> GO TO 8.
8.
FINAL CHECK
Perform “DTC CONFIRMATION PROCEDURE” again to make sure that the repair is correctly performed.
Check that malfunctions are not reproduced when obtaining the malfunction information from the customer,
referring to the symptom inspection result in step 3 or 4.
Is DTC or malfunction symptom reproduced?
YES-1 (DTC is reproduced.)>>GO TO 5.
YES-2 (Malfunction is reproduced.)>>GO TO 6.
NO
>> Before delivering the vehicle to the customer, make sure that DTC is erased.
Diagnostic Work Sheet
INFOID:0000000012201122
DESCRIPTION
There are many operating conditions that may cause a malfunction
of the transmission parts. By understanding those conditions prop-
erly, a quick and exact diagnosis can be achieved.
In general, perception of a problem varies depending on individuals.
Ask the customer about his/her concerns carefully. It is important to
understand the phenomenon or status. To systemize all the informa-
tion for the diagnosis, prepare the question sheet referring to the
question points.
In some cases, multiple conditions that appear simultaneously may
cause a DTC to be detected.
Worksheet Sample
SEF907L
Question sheet
Customer's
name
MR/MS
Registration
number
Initial year
registration
Year
Month
day
Vehicle type
Chassis No.
Storage date
Year
Month
day
Engine
Mileage
km/mile
Symptom
Vehicle does not start. (
R position
D position
M position)
Upshifting does not occur.
Downshifting does not occur.
Lock-up malfunction
Shift point is too high.
Shift point is too low.
Shift shock (
N
⇒
D
Lock-up
R, D, and M position)
Slip (
N
⇒
D
Lock-up
R, D, and M position)
Noise
Vibration
When selector lever position is shifted, shift pattern does not change.
Other
(
)
First occurrence
Recently (as from month
of year
)
Frequency of occurrence
Always
Under certain conditions
Sometimes (
time(s)/day)
Revision: November 2015
2016 JUKE
TM-428
< BASIC INSPECTION >
[CVT: RE0F10D]
DIAGNOSIS AND REPAIR WORK FLOW
Climate con-
ditions
Irrelevant
Weather
Clear
Cloud
Rain
Snow
Others
)
Temperature
Hot
Warm
Cool
Cold
Temperature (Approx.
°
C/
°
F)
Relative humidity
High
Moderate
Low
Transaxle condition
In cold-start
During warm-up (approx.
°
C/
°
F)
After warm-up
Engine speed:
rpm
Road conditions
Urban area
Suburb area
Highway
Mountainous road (uphill or downhill)
Operating condition, etc.
Irrelevant
When engine starts
During idling
During driving
During acceleration
At constant speed driving
During deceleration
During cornering (RH curve or LH curve)
Other conditions
Question sheet
Customer's
name
MR/MS
Registration
number
Initial year
registration
Year
Month
day
Vehicle type
Chassis No.
Storage date
Year
Month
day
Engine
Mileage
km/mile
Revision: November 2015
2016 JUKE
ADDITIONAL SERVICE WHEN REPLACING TCM
TM-429
< BASIC INSPECTION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
ADDITIONAL SERVICE WHEN REPLACING TCM
Description
INFOID:0000000012201123
Always perform the following items when the TCM is replaced. For work procedure, refer to
.
TCM PROGRAMMING
• Since vehicle specifications are not yet written in a new TCM, it is necessary to write them with CONSULT.
CAUTION:
When replacing TCM, save TCM data on CONSULT before removing TCM.
SAVING AND WRITING OF TCM DATA
• TCM performs accurate control by retrieving data (inherent characteristic value) of each solenoid. For this
reason, it is necessary to save data of current TCM in CONSULT before replacing the TCM. After this, the
saved data must be written in new TCM.
Work Procedure
INFOID:0000000012201124
1.
CHECK NEW TCM PART NUMBER
Check new TCM part number to see whether it is blank TCM or not.
NOTE:
• Part number of blank TCM is 310F6-XXXXX.
• Check the part number when ordering TCM or with the one included in the label on the container box.
Is the new TCM a blank TCM?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
SAVING TCM DATA (VEHICLE SPECIFICATIONS)
With CONSULT
1. Turn ignition switch OFF.
2. Turn ignition switch ON.
3. Select “Re/programming, Configuration”.
4. Select “AT/CVT”.
NOTE:
If “AT/CVT” is not displayed and TCM data cannot be saved on CONSULT, GO TO 3.
5. Select “Programming”.
6. Save TCM data on CONSULT according to the CONSULT display.
>> GO TO 3.
3.
REPLACE TCM
1. Turn ignition switch OFF and wait for 10 seconds.
2. Replace TCM. Refer to
TM-554, "Removal and Installation"
.
>> GO TO 4.
4.
LOAD CALIBRATION DATA
1. Shift the selector lever to the “P” position.
2. Turn ignition switch ON.
3. Check that “P” is displayed on shift position indicator on combination meter.
NOTE:
Displayed approximately 4 – 5 seconds after the selector lever is moved to the “P” position.
Does the shift position indicator display “P”?
YES
>> GO TO 5.
NO
>> GO TO 7.
5.
STORE CALIBRATION DATA
1. Turn ignition switch OFF and wait for 5 seconds.
Revision: November 2015
2016 JUKE
TM-430
< BASIC INSPECTION >
[CVT: RE0F10D]
ADDITIONAL SERVICE WHEN REPLACING TCM
2. Turn ignition switch ON.
Does the shift position indicator display “P” at the same time when turning ON the ignition switch?
YES
>> GO TO 6.
NO
>> Check harness between battery and TCM harness connector terminal. Refer to
6.
WRITE TCM DATA (VEHICLE SPECIFICATIONS)
With CONSULT
1. Select “Programming”.
2. Perform programming according to the CONSULT display.
>> WORK END
7.
DETECT MALFUNCTIONING ITEM
Check the following items:
• Harness between the TCM and the ROM assembly inside the transaxle assembly is open or shorted.
• Disconnected, loose, bent, collapsed, or otherwise abnormal connector housing terminals
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
Revision: November 2015
2016 JUKE
ADDITIONAL SERVICE WHEN REPLACING TRANSAXLE ASSEMBLY
TM-431
< BASIC INSPECTION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
ADDITIONAL SERVICE WHEN REPLACING TRANSAXLE ASSEMBLY
Description
INFOID:0000000012201125
Perform the following work after the transaxle assembly is replaced. For work procedure, refer to
.
WRITING TCM DATA
• TCM performs accurate control by retrieving data (inherent characteristic value) of each solenoid. For this
reason, after replacing transaxle assembly, it is necessary to write new data in TCM.
ERASING OF CVT FLUID DEGRADATION LEVEL DATA
• TCM records the degradation level of the CVT fluid calculated from the vehicle driving status. Therefore, if
the transaxle assembly is replaced, it is necessary to erase the CVT fluid degradation level data recorded by
TCM.
Work Procedure
INFOID:0000000012201126
1.
CHECK THE SERIAL NUMBER
Write down the serial number of new transaxle assembly.
>> GO TO 2.
2.
WRITE TCM DATA (IP CHARACTERISTICS VALUE)
NOTE:
Write data of new solenoid in TCM according to the following instructions:
With CONSULT
CAUTION:
When the work is interrupted, obtain data again from the supplied CD.
1. Shift the selector lever to the P position.
2. Turn ignition switch OFF and wait for 10 seconds.
3. Turn ignition switch ON.
4. Insert the supplied CD into CONSULT.
5. Select “Work Support” in “TRANSMISSION”.
6. Select “WRITE IP CHARA - REPLACEMENT AT/CVT”.
7. Check that the serial number displayed on CONSULT screen and those written in the memo agree.
8. Write data in TCM according to the instructions on the CONSULT screen.
NOTE:
When writing is complete, the shift position indicator of the combination meter displays P.
>> GO TO 3.
JSDIA6075GB
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст