Nissan Juke (2016 year). Service Repair Manual — part 70
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
BRC-153
< REMOVAL AND INSTALLATION >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Exploded View
INFOID:0000000012199759
Removal and Installation
INFOID:0000000012199760
REMOVAL
1. Disconnect battery cable from negative terminal.
2. Drain brake fluid. Refer to
3. Remove bracket A.
1.
ABS actuator and electric unit (con-
trol unit)
2.
Bracket A
3.
Bracket B
4.
ABS actuator and electric unit (con-
trol unit) harness connector
A. To front LH caliper
B. To rear RH caliper
C. To rear LH caliper
D. To front RH caliper
E. To master cylinder secondary side
F.
To master cylinder primary side
: Vehicle front
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JSFIA0655GB
Revision: November 2015
2016 JUKE
BRC-154
< REMOVAL AND INSTALLATION >
[WITH VDC]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
4. Disconnect ABS actuator and electric unit (control unit) harness
connector (1), follow the procedure described below.
a. Push the pawl (A).
b. Move the lever (B) in the direction (C) until locked.
c.
Disconnect ABS actuator and electric unit (control unit) harness
connector.
5. Loosen flare nut of brake tube using a flare nut wrench, and then
remove brake tube from ABS actuator and electric unit (control
unit). Refer to
BR-23, "FRONT : Exploded View"
6. Remove ABS actuator and electric unit (control unit) and bracket
B.
CAUTION:
• Never remove and never install ABS actuator and electric unit (control unit) by holding harness
connector.
• Be careful not to drop ABS actuator and electric unit (control unit) and apply excessive impact to
it.
7. Remove bracket B and bushing from ABS actuator and electric unit (control unit).
INSTALLATION
Note the following, and install in the reverse order of removal.
• When replacing with a new ABS actuator and electric unit (control unit), never remove the protector of the
brake tube mounting hole until right before the brake tube is installed.
• When installing brake tube, tighten to the specified torque using a crowfoot and torque wrench so that flare
nut and brake tube are not damaged. Refer to
BR-23, "FRONT : Exploded View"
.
• Never remove and install ABS actuator and electric unit (control unit) by holding actuator harness.
• Bleed air from brake piping after installation. Refer to
BR-13, "Bleeding Brake System"
.
• Never apply excessive impact to actuator, such as by dropping it.
• After installing the ABS actuator and electric unit (control unit) har-
ness connector (1), move the lever (A) in the direction (B) to
secure the locking.
• Perform steering angle sensor neutral position adjustment when
ABS actuator and electric unit (control unit) is replaced. Refer to
JPFIC0194ZZ
JPFIC0195ZZ
Revision: November 2015
2016 JUKE
YAW RATE/SIDE/DECEL G SENSOR
BRC-155
< REMOVAL AND INSTALLATION >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
YAW RATE/SIDE/DECEL G SENSOR
Exploded View
INFOID:0000000012199761
Removal and Installation
INFOID:0000000012199762
REMOVAL
CAUTION:
Never drop or strike yaw rate/side/decel G sensor, because it has little endurance to impact. Never use
a pneumatic tool.
1. Remove front seat (right side). Refer to
SE-21, "Removal and Installation"
2. Remove floor carpet. Refer to
INT-24, "Removal and Installation"
3. Disconnect yaw rate/side/decel G sensor harness connector.
4. Remove yaw rate/side/decel G sensor.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Never drop or strike yaw rate/transverse/decel G sensor, because it has little endurance to impact. Never
use a power tool.
1.
Yaw rate/side/decel G sensor
2.
Yaw rate/side/decel G sensor har-
ness connector
3.
Bracket
: Vehicle front
: N·m (kg-m, in-lb)
JSFIA0544GB
Revision: November 2015
2016 JUKE
BRC-156
< REMOVAL AND INSTALLATION >
[WITH VDC]
STEERING ANGLE SENSOR
STEERING ANGLE SENSOR
Removal and Installation
INFOID:0000000012199763
REMOVAL
1. Remove spiral cable assembly. Refer to
SR-15, "Removal and Installation"
2. Remove steering angle sensor.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform steering angle sensor neutral position adjustment when steering angle sensor is removed and
installed, or replaced. Refer to
.
Revision: November 2015
2016 JUKE
VDC OFF SWITCH
BRC-157
< REMOVAL AND INSTALLATION >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
VDC OFF SWITCH
Removal and Installation
INFOID:0000000012199764
REMOVAL
1. Remove lower instrument panel. Refer to
IP-13, "Removal and Installation"
.
2. Remove VDC OFF switch.
INSTALLATION
Installation is the reverse order of removal.
Revision: November 2015
2016 JUKE
BRC-158
< REMOVAL AND INSTALLATION >
[WITH VDC]
VDC OFF SWITCH
Revision: November 2015
2016 JUKE
BRM-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
D
E
F
G
H
I
J
L
M
SECTION
BRM
A
B
BRM
N
O
P
CONTENTS
BODY REPAIR
VEHICLE INFORMATION . . . . . . . .
BODY EXTERIOR PAINT COLOR . . . . . .
Body Exterior Paint Color . . . . . . . . . . ..
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Body Repair . . . . . . . . .....
REPAIRING HIGH STRENGTH STEEL . . . ..
High Strength Steel (HSS) . . . . . . . . . ..
Handling of Ultra High Strength Steel Plate Parts . ..
PREPARATION . . . . . . . . . . ...
REPAIRING MATERIAL . . . . . . . . .
Foam Repair . . . . . . . . . . . . . . ...
BODY COMPONENT PARTS . . . . . . .
Underbody Component Parts (2WD Models) . . ..
Underbody Component Parts (AWD Models) . . .
Body Component Parts (2WD Models) . . . . ...
Body Component Parts (AWD Models) . . . . ...
REMOVAL AND INSTALLATION . . . ...
CORROSION PROTECTION . . . . . . . .
Description . . . . . . . . . . . . . . . ..
Anti-corrosive Wax . . . . . . . . . . . . ..
Undercoating (2WD Models) . . . . . . . . ...
Undercoating (AWD Models) . . . . . . . . ..
Body Sealing (2WD Models) . . . . . . . . ...
Body Sealing (AWD Models) . . . . . . . . ...
BODY CONSTRUCTION . . . . . . . . .
Body Construction (Standard roof Models) . . . .
Body Construction (With sunroof Models) . . . ...
Rear Fender Hemming Process . . . . . . . ..
REPLACEMENT OPERATIONS . . . . . .
Precautions for Body Repair . . . . . . . . ...
Description . . . . . . . . . . . . . . . ..
Radiator Core Support . . . . . . . . . . . .
Hoodledge . . . . . . . . . . . . . . . ...
Hoodledge (Partial Replacement) . . . . . . ...
Front Side Member . . . . . . . . . . . . ..
Front Side Member (Partial Replacement) . . . ..
Front Pillar . . . . . . . . . . . . . . . ...
Center Pillar (Standard Roof Models) . . . . . ..
Center Pillar (With Sunroof Models) . . . . . .
Outer Sill (Partial Replacement) . . . . . . . ..
Outer Sill . . . . . . . . . . . . . . . . ..
Rear Fender (2WD Models) . . . . . . . . .
Rear Fender (AWD Models) . . . . . . . . .
Rear Fender Extension (2WD Models) . . . . .
Rear Fender Extension (AWD Models) . . . . ...
Rear Panel (2WD Models) . . . . . . . . . ...
Rear Panel (AWD Models) . . . . . . . . . ..
Rear Floor Rear (2WD Models) . . . . . . . ...
Rear Floor Rear (AWD Models) . . . . . . . ..
Rear Side Member (AWD Models Partial Replace-
ment) . . . . . . . . . . . . . . . . . ...
Rear Side Member Extension (2WD Models) . . ..
Rear Side Member Extension (AWD Models) . . .
Roof (Standard Roof Models) . . . . . . . . ..
Roof (Sunroof Models) . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
BODY ALIGNMENT . . . . . . . . . . ..
Body Center Marks . . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ...
Engine Compartment . . . . . . . . . . . ...
Underbody (2WD Models) . . . . . . . . . ...
Underbody (AWD Models) . . . . . . . . . ...
Passenger Compartment . . . . . . . . . . .
Rear Body . . . . . . . . . . . . . . . ...
LOCATION OF PLASTIC PARTS . . . . .
Precautions for Plastics . . . . . . . . . . ...
Location of Plastic Parts . . . . . . . . . . ..
Revision: November 2015
2016 JUKE
BRM-2
< VEHICLE INFORMATION >
BODY EXTERIOR PAINT COLOR
VEHICLE INFORMATION
BODY EXTERIOR PAINT COLOR
Body Exterior Paint Color
INFOID:0000000012199822
EXCEPT FOR PERSONALIZE PACKAGE, NISMO AND NISMO RS
NOTE:
Component
Color code
BA20
BEAV
BGAB
BK23
BKAD
BKH3
BNAH
BQAB
BRBR
Description
Red
Yellow
Black
Silver
Gray
Black
Red
White
Blue
Paint type
Note
2S
2P
2M
2M
2M
2S
2PM
3P
2P
Hard clear
coat
×
−
×
−
−
×
×
−
×
Front
grille
Center
molding
Chromium
plate
Cr
Cr
Cr
Cr
Cr
Cr
Cr
Cr
Cr
Front
bumper
molding
Black
Black
Black
Black
Black
Black
Black
Black
Black
Black
Emblem
Chromium
plate
Cr
Cr
Cr
Cr
Cr
Cr
Cr
Cr
Cr
Front bumper fascia
Body color
BA20
BEAV
BGAB
BK23
BKAD
BKH3
BNAH
BQAB
BRBR
Front bumper fascia
lower
Material color
−
−
−
−
−
−
−
−
−
Front fillet molding
Material color
−
−
−
−
−
−
−
−
−
Door mirror cover
Body color
BA20
BEAV
BGAB
BK23
BKAD
BKH3
BNAH
BQAB
BRBR
Door mirror housing
Black
Black
Black
Black
Black
Black
Black
Black
Black
Black
Back door finisher
Body color
BA20
BEAV
BGAB
BK23
BKAD
BKH3
BNAH
BQAB
BRBR
Rear bumper fascia
Body color
BA20
BEAV
BGAB
BK23
BKAD
BKH3
BNAH
BQAB
BRBR
Rear bumper fascia
lower
Material color
−
−
−
−
−
−
−
−
−
Rear fillet molding
Material color
−
−
−
−
−
−
−
−
−
Sill cover
Material color
−
−
−
−
−
−
−
−
−
Front door outside
handle
Body color
BA20
BEAV
BGAB
BK23
BKAD
BKH3
BNAH
BQAB
BRBR
Rear door outside
handle assembly
Black
Black
Black
Black
Black
Black
Black
Black
Black
Black
JSKIA7531ZZ
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст