Nissan Juke (2016 year). Service Repair Manual — part 305

POSITIVE CRANKCASE VENTILATION

EC-1255

< PERIODIC MAINTENANCE >

[MR EXCEPT FOR NISMO RS MODELS]

POSITIVE CRANKCASE VENTILATION

Inspection

INFOID:0000000012198780

CHECK PCV VALVE

With engine running at idle, remove PCV valve from rocker cover. A

properly working valve makes a hissing noise as air passes through

it. A strong vacuum should be felt immediately when a finger is

placed over valve inlet.
Is the inspection result normal?

YES

>> INSPECTION END

>> Replace PCV valve.

PBIB1589E

Revision: November 2015

2016 JUKE

EC-1256

< REMOVAL AND INSTALLATION >

[MR EXCEPT FOR NISMO RS MODELS]

ECM

REMOVAL AND INSTALLATION

ECM

Removal and Installation

INFOID:0000000012198781

CAUTION:

Perform ADDITIONAL SERVICE WHEN REPLACING ECM. Refer to

EC-749, "Work Procedure"

REMOVAL

1. Remove fusible link bracket. Keep a service area.
2. Disconnect ECM harness connectors. Refer to

PG-6, "Harness Connector"

3. Remove ECM mounting nuts, and then remove ECM.

INSTALLATION

Install in the reverse order of removal.

Revision: November 2015

2016 JUKE

G SENSOR

EC-1257

< REMOVAL AND INSTALLATION >

[MR EXCEPT FOR NISMO RS MODELS]

G SENSOR

Exploded View

INFOID:0000000012198782

Removal and Installation

INFOID:0000000012198783

CAUTION:

• Never drop or strike G sensor, because it has little tolerance for impact.

• Never use a power tool to avoid impact.

REMOVAL

1. Disconnect the battery cable from the negative terminal. Refer to

PG-106, "Removal and Installation"

2. Remove driver seat (LHD) or passenger seat (RHD). Refer to

SE-21, "Removal and Installation"

3. Remove center pillar lower garnish (left side) and dash side finisher (left side). Refer to

INT-22, "CENTER

PILLAR LOWER GARNISH : Removal and Installation"

(center pillar lower garnish) and

INT-21, "DASH

SIDE FINISHER : Removal and Installation"

(dash side finisher).

4. Pull up floor carpet. Refer to

INT-24, "Removal and Installation"

5. Disconnect G sensor harness connector.
6. Remove G sensor.

INSTALLATION

Installation is the reverse order of removal.

Adjustment

INFOID:0000000012198784

ADJUSTMENT AFTER INSTALLATION

Perform “CALIBRATION OF G SENSOR”. Refer to

EC-763, "Description"

G sensor
: Vehicle front

: N·m (kg-m, ft-lb)

JSDIA2139GB

Revision: November 2015

2016 JUKE

EC-1258

< SERVICE DATA AND SPECIFICATIONS (SDS)

[MR EXCEPT FOR NISMO RS MODELS]

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

Idle Speed

INFOID:0000000012198785

*: Under the following conditions
• A/C switch: OFF
• Electric load: OFF (Lights, heater fan & rear window defogger)
• Steering wheel: Kept in straight-ahead position

Ignition Timing

INFOID:0000000012198786

*: Under the following conditions
• A/C switch: OFF
• Electric load: OFF (Lights, heater fan & rear window defogger)
• Steering wheel: Kept in straight-ahead position

Calculated Load Value

INFOID:0000000012198787

Mass Air Flow Sensor

INFOID:0000000012198788

*: Engine is warmed up to normal operating temperature and running under no load.

Transmission

Condition

Specification

CVT

No load* (in P or N position)

650

50 rpm