Nissan Juke (2016 year). Service Repair Manual — part 356
EXL-70
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
FRONT FOG LAMP CIRCUIT
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK FRONT FOG LAMP GROUND CIRCUIT
Check continuity between front fog lamp harness connector and ground.
Is the inspection result normal?
YES
>> Replace the corresponding front fog lamp bulb. Refer to
NO
>> Repair or replace harness.
IPDM E/R
Front fog lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E12
19
E48
1
Existed
LH
20
E30
Front fog lamp
—
Continuity
Connector
Terminal
RH
E48
2
Ground
Existed
LH
E30
Revision: November 2015
2016 JUKE
TURN SIGNAL LAMP CIRCUIT
EXL-71
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
TURN SIGNAL LAMP CIRCUIT
Component Function Check
INFOID:0000000012201657
1.
CHECK TURN SIGNAL LAMP OPERATION
With CONSULT
1. Turn ignition switch ON.
2. Select “FLASHER” of “BCM” using CONSULT.
3. Select “FLASHER” in “Active Test” mode.
4. With operating the test items, check that the turn signal lamps is turned ON.
Is the inspection result normal?
YES
>> Turn signal lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012201658
1.
CHECK TURN SIGNAL LAMP POWER SUPPLY
With CONSULT
1. Turn ignition switch OFF.
2. Disconnect the following connectors.
-
Front turn signal lamp
-
Door mirror
-
Rear combination lamp
3. Turn ignition switch ON.
4. Select “FLASHER” of “BCM” using CONSULT.
5. Select “FLASHER” in “Active Test” mode.
6. With operating the test items, check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK TURN SIGNAL LAMP POWER SUPPLY CIRCUIT (SHORT)
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
RH
: Turn signal lamps (RH) ON
LH
: Turn signal lamps (LH) ON
Off
: Turn signal lamps OFF
+
-
Test item
Voltage
BCM
Connector
Terminal
RH
M69
61
Ground
FLASHER
RH
9 – 16 V
Off
0 V
LH
60
LH
9 – 16 V
Off
0 V
BCM
—
Continuity
Connector
Terminal
RH
M69
61
Ground
Not existed
LH
60
Revision: November 2015
2016 JUKE
EXL-72
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
TURN SIGNAL LAMP CIRCUIT
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK TURN SIGNAL LAMP POWER SUPPLY CIRCUIT (OPEN)
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector and each turn signal lamp harness connector.
Front turn signal lamp
Side turn signal lamp
Rear turn signal lamp
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK TURN SIGNAL LAMP GROUND CIRCUIT
Check continuity between each turn signal lamp harness connector and ground.
Front turn signal lamp
Side turn signal lamp
Rear turn signal lamp
Is the inspection result normal?
YES-1 >> Front turn signal lamp or rear turn signal lamp: GO TO 5.
YES-2 >> Side turn signal lamp: Replace the corresponding side turn signal lamp. Refer to
.
NO
>> Repair or replace harness.
BCM
Front turn signal lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
M69
61
E47
1
Existed
LH
60
E34
BCM
Door mirror
Continuity
Connector
Terminal
Connector
Terminal
RH
M69
61
D9
13
Existed
LH
60
D30
BCM
Rear combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
M69
61
B59
5
Existed
LH
60
B80
Front turn signal lamp
—
Continuity
Connector
Terminal
RH
E47
2
Ground
Existed
LH
E34
Door mirror
—
Continuity
Connector
Terminal
RH
D9
2
Ground
Existed
LH
D30
Rear combination lamp
—
Continuity
Connector
Terminal
RH
B59
3
Ground
Existed
LH
B80
Revision: November 2015
2016 JUKE
TURN SIGNAL LAMP CIRCUIT
EXL-73
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
5.
CHECK TURN SIGNAL LAMP BULB
Check the applicable turn signal lamp bulb.
Is the inspection result normal?
YES-1 >> Front turn signal lamp: Check the corresponding front turn signal lamp bulb socket. Repair or
replace if necessary.
YES-2 >> Rear turn signal lamp: Check the corresponding rear turn signal lamp bulb socket and harness.
Repair or replace if necessary.
NO
>> Replace the corresponding turn signal lamp bulb. Refer to
signal lamp) or
(rear turn signal lamp).
Revision: November 2015
2016 JUKE
EXL-74
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
OPTICAL SENSOR
OPTICAL SENSOR
Component Function Check
INFOID:0000000012201659
1.
CHECK OPTICAL SENSOR SIGNAL
With CONSULT
1. Turn ignition switch ON.
2. Select “HEAD LAMP” of “BCM” using CONSULT.
3. Select “OPTI SEN (DTCT)” in “Data Monitor” mode.
4. Turn lighting switch AUTO.
5. With the optical sensor illuminating, check the monitor status.
*: Illuminates the optical sensor. The value may be less than the standard value if brightness is weak.
Is the inspection result normal?
YES
>> Optical sensor is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012201660
1.
CHECK OPTICAL SENSOR POWER SUPPLY
1. Turn ignition switch ON.
2. Turn lighting switch AUTO.
3. Check voltage between optical sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK OPTICAL SENSOR GROUND
Check voltage between optical sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 6.
3.
CHECK OPTICAL SENSOR SIGNAL
With illuminating the optical sensor, check voltage between optical sensor harness connector and ground.
Monitor item
Condition
Voltage
(Approx.)
OPTI SEN (DTCT) Optical sensor
When illuminating
3.1 V or more *
When shutting off light
0.6 V or less
+
-
Voltage
(Approx.)
Optical sensor
Connector
Terminal
M84
1
Ground
5 V
+
-
Voltage
(Approx.)
Optical sensor
Connector
Terminal
M84
3
Ground
0 V
Revision: November 2015
2016 JUKE
OPTICAL SENSOR
EXL-75
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
*: Illuminate the optical sensor. The value may be less than the standard if brightness is weak.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Replace optical sensor. Refer to
EXL-105, "Removal and Installation"
4.
CHECK OPTICAL SENSOR POWER SUPPLY CIRCUIT (OPEN)
1. Turn ignition switch OFF.
2. Disconnect optical sensor connector and BCM connector.
3. Check continuity between optical sensor harness connector and BCM harness connector.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK OPTICAL SENSOR POWER SUPPLY CIRCUIT (SHORT)
Check continuity between optical sensor harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair or replace harness.
6.
CHECK OPTICAL SENSOR GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect optical sensor connector and BCM connector.
3. Check continuity between optical sensor harness connector and BCM harness connector.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair or replace harness.
7.
CHECK OPTICAL SENSOR SIGNAL CIRCUIT (OPEN)
1. Turn ignition switch OFF.
2. Disconnect optical sensor connector and BCM connector.
3. Check continuity between optical sensor harness connector and BCM harness connector.
+
-
Condition
Voltage
(Approx.)
Optical sensor
Connector
Terminal
M84
2
Ground
Optical sensor
When illuminating
3.1 V or more*
When shutting off light
0.6 V or less
Optical sensor
BCM
Continuity
Connector
Terminal
Connector
Terminal
M84
1
M68
17
Existed
Optical sensor
—
Continuity
Connector
Terminal
M84
1
Ground
Not existed
Optical sensor
BCM
Continuity
Connector
Terminal
Connector
Terminal
M84
3
M68
18
Existed
Revision: November 2015
2016 JUKE
EXL-76
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
OPTICAL SENSOR
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair or replace harness.
8.
CHECK OPTICAL SENSOR SIGNAL CIRCUIT (SHORT)
Check continuity between optical sensor harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair or replace harness.
Optical sensor
BCM
Continuity
Connector
Terminal
Connector
Terminal
M84
2
M68
14
Existed
Optical sensor
—
Continuity
Connector
Terminal
M84
2
Ground
Not existed
Revision: November 2015
2016 JUKE
HAZARD SWITCH
EXL-77
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HAZARD SWITCH
Component Function Check
INFOID:0000000012201661
1.
CHECK HAZARD SWITCH SIGNAL
With CONSULT
1. Turn ignition switch ON.
2. Select “FLASHER” of “BCM” using CONSULT.
3. Select “HAZARD SW” in “Data Monitor” mode.
4. With operating the hazard switch, check the monitor status.
Is the inspection result normal?
YES
>> Hazard switch circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012201662
1.
CHECK HAZARD SWITCH SIGNAL
1. Turn ignition switch OFF.
2. Disconnect hazard switch connector.
3. Check voltage between hazard switch connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK HAZARD SWITCH SIGNAL CIRCUIT (OPEN)
1. Disconnect BCM connector.
2. Check continuity between hazard switch harness connector and BCM harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK HAZARD SWITCH SIGNAL CIRCUIT (SHORT)
Check continuity between hazard switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
Monitor item
Condition
Monitor status
HAZARD SW
Hazard switch
ON
On
OFF
Off
+
-
Voltage
(Approx.)
Hazard switch
Connector
Terminal
M45
2
Ground
12 V
Hazard switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
M45
2
M68
29
Existed
Hazard switch
—
Continuity
Connector
Terminal
M45
2
Ground
Not existed
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст