Nissan Juke (2016 year). Service Repair Manual — part 205
P1451 PRESSURE SENSOR
EC-455
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
YES
>> GO TO 3.
NO
>> Replace EVAP control system pressure sensor. Refer to
3.
CHECK TURBOCHARGER BOOST SENSOR
Check turbocharger boost sensor. Refer to
EC-455, "Component Inspection (Turbocharger Boost Sensor)"
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Replace turbocharger boost sensor (with intake temperature sensor 2). Refer to
Component Inspection (EVAP Control System Pressure Sensor)
INFOID:0000000012198007
1.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
1. Turn ignition switch OFF.
2. Remove EVAP control system pressure sensor with its harness connector connected from EVAP canister.
Always replace O-ring with a new one.
3. Install a vacuum pump to EVAP control system pressure sensor.
4. Turn ignition switch ON and check output voltage between ECM harness connector and ground under the
following conditions.
CAUTION:
• Always calibrate the vacuum pump gauge when using it.
• Do not apply below -93.3 kPa (-0.952 kg/cm
2
, -13.53 psi) or pressure over 101.3 kPa (1.033 kg/
cm
2
, 14.69 psi).
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace EVAP control system pressure sensor. Refer to
Component Inspection (Turbocharger Boost Sensor)
INFOID:0000000012198008
1.
CHECK TURBOCHARGER BOOST SENSOR
1. Turn ignition switch OFF.
2. Remove turbocharger boost sensor with its harness connector.
3. Install pressure pump (A) to turbocharger boost sensor (1).
CAUTION:
When insert a pressure pump hose to the sensor, be careful
to the damage of the sensor housing.
4. Turn ignition switch ON.
5. Check the voltage between ECM harness connector terminals
as per the following conditions.
NOTE:
• Always calibrate the pressure pump gauge when using it.
• Inspection should be done at room temperature [10 - 30
°
C (50 - 86
°
F)].
ECM
Condition
[Applied vacuum kPa (kg/cm
2
, psi)]
Voltage
Connector
+
−
Terminal
F25
15
12
Not applied
0.5 - 4.6 V
-26.7 (-0.272, -3.87)
2.1 to 2.5 V lower than above value
JMBIA0871ZZ
Revision: November 2015
2016 JUKE
EC-456
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
P1451 PRESSURE SENSOR
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace turbocharger boost sensor. Refer to
.
ECM
Condition [Pressure (Relative to at-
mospheric pressure)]
Voltage
(Approx.)
Connector
+
−
Terminal
F25
41
44
0 kPa
(0 mbar, 0 mmHg, 0 inHg)
2.03 V
40 kPa
(400 mbar, 300 mmHg, 11.81 inHg)
2.67 V
Revision: November 2015
2016 JUKE
P1550 BATTERY CURRENT SENSOR
EC-457
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P1550 BATTERY CURRENT SENSOR
DTC Logic
INFOID:0000000012198009
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and wait at least 10 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012198010
1.
CHECK BATTERY CURRENT SENSOR POWER SUPPLY
DTC No.
Trouble diagnosis name
(Trouble diagnosis content)
DTC detecting condition
Possible cause
P1550
BAT CURRENT SENSOR
(Battery current sensor circuit
range/performance)
The output voltage of the battery current
sensor remains within the specified
range while engine is running.
• Harness or connectors
(Battery current sensor circuit is open
or shorted.)
(Camshaft position sensor circuit is
open or shorted)
(Fuel rail pressure sensor circuit is
open or shorted.)
(G sensor circuit is open or shorted.)
(Exhaust valve timing control position
sensor circuit is open or shorted.)
(Accelerator pedal position sensor 2
circuit is open or shorted.)
(Turbocharger boost sensor circuit is
open or shorted.)
(Engine oil pressure sensor circuit is
open or shorted.)
• Battery current sensor
• Camshaft position sensor
• Camshaft (Intake)
• Starter motor
• Starting system circuit
• Dead (Weak) battery
• Fuel rail pressure sensor
• G sensor
• Exhaust valve timing control position
sensor
• Accelerator pedal position sensor 2
• Turbocharger boost sensor
• Engine oil pressure sensor
Revision: November 2015
2016 JUKE
EC-458
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
P1550 BATTERY CURRENT SENSOR
1. Turn ignition switch OFF.
2. Disconnect battery current sensor harness connector.
3. Turn ignition switch ON.
4. Check the voltage between battery current sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK SENSOR POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check harness connector for short to power and short to ground, between the following terminals.
Is the inspection result normal?
YES
>> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
3.
CHECK BATTERY CURRENT SENSOR GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between battery current sensor harness connector and ECM harness connector.
4. Also check harness for short to power.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.
CHECK BATTERY CURRENT SENSOR INPUT SIGNAL CIRCUIT
1. Check the continuity between battery current sensor harness connector and ECM harness connector.
+
-
Voltage
(Approx.)
Battery current sensor
Connector
Terminal
F52
1
Ground
5 V
ECM
Sensor
Connector
Terminal
Name
Connector
Terminal
F25
39
FRP sensor
F5
1
EOP sensor
F43
3
Turbocharger boost sensor
F75
1
F26
68
Battery current sensor
F52
1
G sensor
B32
3
72
CMP sensor
F109
1
EVT control position sensor
F110
1
E18
118
APP sensor 2
E101
5
+
−
Continuity
Battery current sensor
ECM
Connector
Terminal
Connector
Terminal
F52
3
F26
87
Existed
Revision: November 2015
2016 JUKE
P1550 BATTERY CURRENT SENSOR
EC-459
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace error-detected parts
5.
CHECK BATTERY CURRENT SENSOR
Check the battery current sensor. Refer to
EC-459, "Component Inspection"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Replace battery negative cable assembly. Refer to
Component Inspection
INFOID:0000000012198011
1.
CHECK BATTERY CURRENT SENSOR
1. Turn ignition switch OFF.
2. Reconnect harness connectors disconnected.
3. Disconnect battery negative cable.
4. Install jumper cable between battery negative terminal and body
ground.
5. Turn ignition switch ON.
6. Check the voltage between ECM harness connector and
ground.
Before measuring the terminal voltage, confirm that the battery is fully charged. Refer to
PG-97, "How to Handle Battery"
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace battery negative cable assembly. Refer to
+
−
Continuity
Battery current sensor
ECM
Connector
Terminal
Connector
Terminal
F52
4
F26
80
Existed
JPBIA3286ZZ
ECM
Voltage
(Approx.)
Connector
+
-
Terminal
F26
80
87
2.5 V
Revision: November 2015
2016 JUKE
EC-460
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
P1551, P1552 BATTERY CURRENT SENSOR
P1551, P1552 BATTERY CURRENT SENSOR
DTC Logic
INFOID:0000000012198012
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8 V with ignition
switch ON
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON and wait at least 10 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
DTC No.
Trouble diagnosis name
(Trouble diagnosis content)
DTC detecting condition
Possible cause
P1551
BAT CURRENT SENSOR
(Battery current sensor circuit
low input)
An excessively low voltage from the sen-
sor is sent to ECM.
• Harness or connectors
(Battery current sensor circuit is open
or shorted.)
(Camshaft position sensor circuit is
open or shorted)
(Fuel rail pressure sensor circuit is
open or shorted.)
(G sensor circuit is open or shorted.)
(Exhaust valve timing control position
sensor circuit is open or shorted.)
(Accelerator pedal position sensor 2
circuit is open or shorted.)
(Turbocharger boost sensor circuit is
open or shorted.)
(Engine oil pressure sensor circuit is
open or shorted.)
• Battery current sensor
• Camshaft position sensor
• Camshaft (Intake)
• Starter motor
• Starting system circuit
• Dead (Weak) battery
• Fuel rail pressure sensor
• G sensor
• Exhaust valve timing control position
sensor
• Accelerator pedal position sensor 2
• Turbocharger boost sensor
• Engine oil pressure sensor
P1552
BAT CURRENT SENSOR
(Battery current sensor circuit
high input)
An excessively high voltage from the sen-
sor is sent to ECM.
Revision: November 2015
2016 JUKE
P1551, P1552 BATTERY CURRENT SENSOR
EC-461
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Diagnosis Procedure
INFOID:0000000012198013
1.
CHECK BATTERY CURRENT SENSOR POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect battery current sensor harness connector.
3. Turn ignition switch ON.
4. Check the voltage between battery current sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK SENSOR POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check harness connector for short to power and short to ground, between the following terminals.
Is the inspection result normal?
YES
>> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
3.
CHECK BATTERY CURRENT SENSOR GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between battery current sensor harness connector and ECM harness connector.
4. Also check harness for short to power.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.
CHECK BATTERY CURRENT SENSOR INPUT SIGNAL CIRCUIT
1. Check the continuity between battery current sensor harness connector and ECM harness connector.
+
-
Voltage
(Approx.)
Battery current sensor
Connector
Terminal
F52
1
Ground
5 V
ECM
Sensor
Connector
Terminal
Name
Connector
Terminal
F25
39
FRP sensor
F5
1
EOP sensor
F43
3
Turbocharger boost sensor
F75
1
F26
68
Battery current sensor
F52
1
G sensor
B32
3
72
CMP sensor
F109
1
EVT control position sensor
F110
1
E18
118
APP sensor 2
E101
5
+
−
Continuity
Battery current sensor
ECM
Connector
Terminal
Connector
Terminal
F52
3
F26
87
Existed
Revision: November 2015
2016 JUKE
EC-462
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
P1551, P1552 BATTERY CURRENT SENSOR
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace error-detected parts
5.
CHECK BATTERY CURRENT SENSOR
Check the battery current sensor. Refer to
EC-459, "Component Inspection"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Replace battery negative cable assembly. Refer to
Component Inspection
INFOID:0000000012198014
1.
CHECK BATTERY CURRENT SENSOR
1. Turn ignition switch OFF.
2. Reconnect harness connectors disconnected.
3. Disconnect battery negative cable.
4. Install jumper cable between battery negative terminal and body
ground.
5. Turn ignition switch ON.
6. Check the voltage between ECM harness connector and
ground.
Before measuring the terminal voltage, confirm that the battery is fully charged. Refer to
PG-97, "How to Handle Battery"
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace battery negative cable assembly. Refer to
+
−
Continuity
Battery current sensor
ECM
Connector
Terminal
Connector
Terminal
F52
4
F26
80
Existed
JPBIA3286ZZ
ECM
Voltage
(Approx.)
Connector
+
-
Terminal
F26
80
87
2.5 V
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст