Nissan Juke (2016 year). Service Repair Manual — part 680
WCS-32
< WIRING DIAGRAM >
WARNING CHIME SYSTEM
JRNWF0722GB
Revision: November 2015
2016 JUKE
WCS
WARNING CHIME SYSTEM
WCS-33
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
JRNWF0723GB
Revision: November 2015
2016 JUKE
WCS-34
< WIRING DIAGRAM >
WARNING CHIME SYSTEM
JRNWF0724GB
Revision: November 2015
2016 JUKE
WCS
WARNING CHIME SYSTEM
WCS-35
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
JRNWF0725GB
Revision: November 2015
2016 JUKE
WCS-36
< WIRING DIAGRAM >
WARNING CHIME SYSTEM
JRNWF0726GB
Revision: November 2015
2016 JUKE
WCS
DIAGNOSIS AND REPAIR WORKFLOW
WCS-37
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
INFOID:0000000012201481
OVERALL SEQUENCE
DETAILED FLOW
1.
OBTAIN INFORMATION ABOUT SYMPTOM
Interview the customer to obtain as much information as possible about the conditions and environment under
which the malfunction occurred.
>> GO TO 2.
2.
CHECK SYMPTOM
• Check the symptom based on the information obtained from the customer.
• Check if any other malfunctions are present.
>> GO TO 3.
3.
CHECK CONSULT SELF-DIAGNOSIS RESULTS
1. Connect CONSULT and perform self-diagnosis. Refer to
WCS-19, "BUZZER : CONSULT Function (BCM
.
2. When DTC is detected, follow the instructions below:
-
Record DTC and Freeze Frame Data.
Are self-diagnosis results normal?
YES
>> GO TO 4.
NO
>> GO TO 5.
JSNIA4492GB
Revision: November 2015
2016 JUKE
WCS-38
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
4.
NARROW DOWN MALFUNCTIONING PARTS BY SYMPTOM DIAGNOSIS
Perform symptom diagnosis and narrow down the malfunctioning parts.
>> GO TO 5.
5.
REPAIR OR REPLACE MALFUNCTIONING PARTS
Repair or replace malfunctioning parts.
NOTE:
If DTC is displayed, erase DTC after repairing or replacing malfunctioning parts.
>> GO TO 6.
6.
FINAL CHECK
Check that the warning buzzer in the combination meter operates normally.
Does it operate normally?
YES
>> INSPECTION END
NO
>> GO TO 1.
Revision: November 2015
2016 JUKE
WCS
POWER SUPPLY AND GROUND CIRCUIT
WCS-39
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
DTC/CIRCUIT DIAGNOSIS
POWER SUPPLY AND GROUND CIRCUIT
COMBINATION METER
COMBINATION METER : Diagnosis Procedure
INFOID:0000000012926228
1.
CHECK FUSE
Check for blown fuses.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Be sure to eliminate cause of malfunction before installing new fuse.
2.
CHECK POWER SUPPLY CIRCUIT
Check voltage between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Check harness between combination meter and fuse.
3.
CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter connector.
3. Check continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair harness or connector.
Power source
Fuse No.
Battery
13
Ignition switch ON or START
5
Ignition switch ACC or ON
19
Terminals
Ignition switch po-
sition
Voltage
(Approx.)
(+)
(
−
)
Combination meter
Ground
Connector
Terminal
M34
27
OFF
Battery voltage
15
ACC
28
ON
Combination meter
Ground
Continuity
Connector
Terminal
M34
21
Existed
22
23
25
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст