Nissan Juke (2016 year). Service Repair Manual — part 681
WCS-40
< DTC/CIRCUIT DIAGNOSIS >
METER BUZZER CIRCUIT
METER BUZZER CIRCUIT
Component Function Check
INFOID:0000000012201483
1.
CHECK OPERATION OF METER BUZZER
1. Select “BUZZER” of “BCM” on CONSULT.
2. Perform “LIGHT WARN ALM” of “Active Test”.
Does meter buzzer beep?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK COMBINATION METER INPUT SIGNAL
Select the “Data Monitor” for the “METER/M&A” and check the “BUZZER” monitor value.
Is the inspection result normal?
YES
>> Replace combination meter.
NO
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
Diagnosis Procedure
INFOID:0000000012201484
1.
CHECK POWER SUPPLY OF COMBINATION METER
Check power supply of combination meter. Refer to
MWI-53, "COMBINATION METER : Diagnosis Proce-
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair power supply circuit of combination meter.
BUZZER
Under the condition of buzzer input
: On
Except above
: Off
Revision: November 2015
2016 JUKE
WCS
SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT
WCS-41
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT
Component Function Check
INFOID:0000000012201485
1.
CHECK COMBINATION METER INPUT SIGNAL
Select the “Data Monitor” for the “METER/M&A” and check the “BUCKLE SW” monitor value.
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012201486
1.
CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter connector and seat belt buckle switch (driver side) connector.
3. Check continuity between combination meter harness connector and seat belt buckle switch (driver side)
harness connector.
4. Check harness continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE) GROUND CIRCUIT
Check harness continuity between seat belt buckle switch (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair harness or connector.
Component Inspection
INFOID:0000000012201487
1.
CHECK SEAT BELT BUCKLE SWITCH UNIT
1. Turn ignition switch OFF.
2. Disconnect the seat belt buckle switch (driver side) connector.
3. Check continuity between terminals.
BUCKLE SW
When driver seat belt is fastened
: Off
When driver seat belt is unfastened
: On
Combination meter
Seat belt buckle switch (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M34
9
B50
1
Existed
Combination meter
Ground
Continuity
Connector
Terminal
M34
9
Not existed
Seat belt buckle switch (driver side)
Ground
Continuity
Connector
Terminal
B50
2
Existed
Revision: November 2015
2016 JUKE
WCS-42
< DTC/CIRCUIT DIAGNOSIS >
SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace the seat belt buckle (driver side). Refer to
SB-9, "SEAT BELT BUCKLE : Removal and
Terminal
Condition
Continuity
1
2
When driver seat belt is fastened
Not existed
When driver seat belt is unfastened
Existed
Revision: November 2015
2016 JUKE
WCS
PARKING BRAKE SWITCH SIGNAL CIRCUIT
WCS-43
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
PARKING BRAKE SWITCH SIGNAL CIRCUIT
Diagnosis Procedure
INFOID:0000000012201488
1.
CHECK COMBINATION METER INPUT SIGNAL
1. Turn ignition switch ON.
2. Check the voltage between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter connector and parking brake switch connector.
3. Check continuity between combination meter harness connector and parking brake switch harness con-
nector.
4. Check continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair harness or connector.
Component Inspection
INFOID:0000000012201489
1.
CHECK PARKING BRAKE SWITCH
Check parking brake switch. Refer to
BRC-132, "Component Inspection"
.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace parking brake switch. Refer to
.
(+)
(
−
)
Condition
Voltage
(Approx.)
Combination meter
Ground
Connector
Terminal
M34
10
Ignition
switch ON
When parking brake is applied
0 V
When parking brake is released
12 V
Terminals
Continuity
Combination meter
Parking brake switch
Connector
Terminal
Connector
Terminal
M34
10
M31
1
Existed
Terminals
Continuity
Combination meter
Ground
Connector
Terminal
M34
10
Not existed
Revision: November 2015
2016 JUKE
WCS-44
< SYMPTOM DIAGNOSIS >
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
SYMPTOM DIAGNOSIS
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
Description
INFOID:0000000012201490
• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is
released.
• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking
brake applied.
Diagnosis Procedure
INFOID:0000000012201491
1.
CHECK PARKING BRAKE WARNING LAMP
1. Start the engine.
2. Check the operation of the brake warning lamp by operating the parking brake.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-64, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
Perform check for the parking brake switch signal circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK PARKING BRAKE SWITCH
Perform a unit check for the parking brake switch. Refer to
WCS-43, "Component Inspection"
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-64, "Removal and Installation"
NO
>> Replace parking brake switch. Refer to
.
When parking brake is applied
: ON
When parking brake is released
: OFF
Revision: November 2015
2016 JUKE
WCS
THE LIGHT REMINDER WARNING DOES NOT SOUND
WCS-45
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE LIGHT REMINDER WARNING DOES NOT SOUND
Description
INFOID:0000000012201492
Light reminder warning chime does not sound even though headlamp is illuminated.
Diagnosis Procedure
INFOID:0000000012201493
1.
CHECK COMBINATION SWITCH (LIGHTING SWITCH) OPERATION
Check that the headlamps operate normally by operating the combination switch (lighting switch).
Do they operate normally?
YES
>> GO TO 2.
NO
>> Refer to
(XENON TYPE) or
TYPE).
2.
CHECK DRIVER SIDE DOOR SWITCH SIGNAL CIRCUIT
Perform the check for the driver side door switch signal circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK DRIVER SIDE DOOR SWITCH
Perform a unit check for the driver side door switch. Refer to
DLK-78, "Component Inspection"
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Replace driver side door switch. Refer to
DLK-169, "Removal and Installation"
Revision: November 2015
2016 JUKE
WCS-46
< SYMPTOM DIAGNOSIS >
THE SEAT BELT WARNING CONTINUES SOUNDING, OR DOES NOT SOUND
THE SEAT BELT WARNING CONTINUES SOUNDING, OR DOES NOT
SOUND
Description
INFOID:0000000012201494
• Seat belt warning does not sound.
• Seat belt warning sounds continuously.
Diagnosis Procedure
INFOID:0000000012201495
1.
CHECK SEAT BELT WARNING LAMP
1. Turn ignition switch ON.
2. Check the operation of the seat belt warning lamp in the combination meter.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK BCM OUTPUT SIGNAL
Check if the seat belt warning chime is activated by performing BCM active test. Refer to
CONSULT Function (BCM - BUZZER)"
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 3.
3.
CHECK COMBINATION METER INPUT SIGNAL
Check if buzzer switches to proper condition (On/Off) on data monitor of combination meter. Refer to
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-64, "Removal and Installation"
NO
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
4.
CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE) CIRCUIT
Perform the check for the seat belt buckle switch (driver side) circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair harness or connector.
5.
CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE)
Perform a unit check for the seat belt buckle switch (driver side). Refer to
WCS-41, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-64, "Removal and Installation"
NO
>> Replace seat belt buckle (driver side). Refer to
SB-9, "SEAT BELT BUCKLE : Removal and Instal-
.
Seat belt fastened
: OFF
Seat belt not fastened
: ON
Buzzer active condition
: On
Buzzer non-active condition
: Off
Revision: November 2015
2016 JUKE
WT-1
SUSPENSION
C
D
F
G
H
I
J
K
L
M
SECTION
WT
A
B
WT
N
O
P
CONTENTS
ROAD WHEELS & TIRES
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Removing Battery Terminal . . .....
Service Notice and Precautions for TPMS . . . ....
Service Notice and Precautions for Road Wheel . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
Component Parts Location . . . . . . . . . ....
Component Description . . . . . . . . . . .....
BCM . . . . . . . . . . . . . . . . . . ..
Tire Pressure Sensor . . . . . . . . . . . ....
Tire Pressure Receiver . . . . . . . . . . .....
Information Display . . . . . . . . . . . . ...
SYSTEM . . . . . . . . . . . . . . . ..
System Description . . . . . . . . . . . . ...
DIAGNOSIS SYSTEM (BCM) . . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . ...
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . ...
AIR PRESSURE MONITOR . . . . . . . . . ..
AIR PRESSURE MONITOR : CONSULT Function
(BCM - AIR PRESSURE MONITOR) . . . . . ..
ECU DIAGNOSIS INFORMATION . . . ..
BCM . . . . . . . . . . . . . . . . .
List of ECU Reference . . . . . . . . . . .
WIRING DIAGRAM . . . . . . . . . ..
TIRE PRESSURE MONITORING SYSTEM . ..
Wiring Diagram . . . . . . . . . . . . . .
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORK FLOW . ...
Work Flow . . . . . . . . . . . . . . . .
ADDITIONAL SERVICE WHEN REPLACING
BCM . . . . . . . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ...
Work Procedure . . . . . . . . . . . . . ...
TIRE PRESSURE SENSOR ID REGISTRA-
TION . . . . . . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ...
Work Procedure . . . . . . . . . . . . . ...
DTC/CIRCUIT DIAGNOSIS . . . . . . .
C1704, C1705, C1706, C1707 LOW TIRE
PRESSURE . . . . . . . . . . . . . ...
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
C1708, C1709, C1710, C1711 TIRE PRES-
SURE SENSOR . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
C1716, C1717, C1718, C1719 TIRE PRES-
SURE SENSOR . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
C1729 VEHICLE SPEED SIGNAL . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
POWER SUPPLY AND GROUND CIRCUIT .
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст