Nissan Juke (2016 year). Service Repair Manual — part 134
AWD WARNING LAMP
DLN-79
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
AWD WARNING LAMP
Component Function Check
INFOID:0000000012199436
1.
CHECK AWD WARNING LAMP FUNCTION
Check that AWD warning lamp turns ON when turn the ignition switch ON. Then, AWD warning lamp turns
OFF approx. 1 second after the engine start.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
.
Diagnosis Procedure
INFOID:0000000012199437
1.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Perform the trouble diagnosis for power supply and ground circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the error-detected parts.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
NO
>> GO TO 3.
3.
CHECK AWD WARNING LAMP SIGNAL
With CONSULT
1. Turn the ignition switch ON.
CAUTION:
Never start the engine.
2. Check “WARNING LAMP” in “DATA MONITOR” for “ALL MODE AWD/4WD”.
Does the item on “DATA MONITOR” indicate “On”?
YES
>> Perform the trouble diagnosis for combination meter power supply circuit. Refer to
"COMBINATION METER : Diagnosis Procedure"
.
NO
>> Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
.
Revision: November 2015
2016 JUKE
DLN-80
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
AWD MODE INDICATOR LAMP (AWD-V)
AWD MODE INDICATOR LAMP (AWD-V)
Component Function Check
INFOID:0000000012199438
1.
AWD MODE INDICATOR LAMP OPERATION CHECK
1. Turn the ignition switch ON.
2. Set AWD mode switch to “AWD-V”.
3. Check that AWD mode indicator lamp (AWD-V) turns on.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
.
Diagnosis Procedure
INFOID:0000000012199439
1.
CHECK AWD WARNING LAMP
1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
2. Stop the vehicle.
Does AWD warning lamp turn ON?
YES
>> Proceed to
.
NO
>> GO TO 2.
2.
CHECK AWD MODE SWITCH
Perform the trouble diagnosis for AWD mode switch. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the error-detected parts.
3.
CHECK AWD MODE INDICATOR LAMP SIGNAL
With CONSULT
1. Start the engine.
CAUTION:
Never drive the vehicle.
2. Change AWD mode switch to “AWD-V” from “2WD”.
3. Check “INDICATOR” in “DATA MONITOR” for “ALL MODE AWD/4WD”.
Does the item on “DATA MONITOR” indicate “AWD-V”?
YES
>> GO TO 4.
NO
>> Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
.
4.
CHECK COMBINATION METER POWER SUPPLY CIRCUIT
Perform the trouble diagnosis for combination meter power supply circuit. Refer to
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace the error-detected parts.
Revision: November 2015
2016 JUKE
AWD MODE INDICATOR LAMP (AWD)
DLN-81
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
AWD MODE INDICATOR LAMP (AWD)
Component Function Check
INFOID:0000000012199440
1.
AWD MODE INDICATOR LAMP OPERATION CHECK
Check that AWD mode indicator lamp (AWD) turns on for approximately 1 second after the ignition switch is
turned ON.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
.
Diagnosis Procedure
INFOID:0000000012199441
1.
CHECK AWD WARNING LAMP
1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
2. Stop the vehicle.
Does AWD warning lamp turn ON?
YES
>> Proceed to
.
NO
>> GO TO 2.
2.
CHECK AWD MODE SWITCH
Perform the trouble diagnosis for AWD mode switch. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the error-detected parts.
3.
CHECK AWD MODE INDICATOR LAMP SIGNAL
With CONSULT
1. Start the engine.
CAUTION:
Stop the vehicle.
2. Change AWD mode switch to “AWD” from “AWD-V”.
3. Check “INDICATOR” in “DATA MONITOR” for “ALL MODE AWD/4WD”.
Does the item on “DATA MONITOR” indicate “AWD”?
YES
>> GO TO 4.
NO
>> Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
.
4.
CHECK COMBINATION METER POWER SUPPLY CIRCUIT
Perform the trouble diagnosis for combination meter power supply circuit. Refer to
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace the error-detected parts.
Revision: November 2015
2016 JUKE
DLN-82
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY21B]
AWD WARNING LAMP DOES NOT TURN ON
SYMPTOM DIAGNOSIS
AWD WARNING LAMP DOES NOT TURN ON
Description
INFOID:0000000012199442
AWD warning lamp does not turn ON when the ignition switch is turned to ON.
Diagnosis Procedure
INFOID:0000000012199443
1.
CHECK AWD WARNING LAMP
Perform the trouble diagnosis for AWD warning lamp. Refer to
Is the inspection result normal?
YES
>> Check each harness connector pin terminal for malfunction or disconnection.
NO
>> Repair or replace the error-detected parts.
Revision: November 2015
2016 JUKE
AWD WARNING LAMP DOES NOT TURN OFF
DLN-83
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
AWD WARNING LAMP DOES NOT TURN OFF
Description
INFOID:0000000012199444
AWD warning lamp does not turn OFF approx. 1 second after the engine started.
Diagnosis Procedure
INFOID:0000000012199445
1.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
NO
>> GO TO 2.
2.
CHECK AWD WARNING LAMP
Perform the trouble diagnosis of the AWD warning lamp. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the error-detected parts.
3.
CHECK AWD CONTROL MODULE POWER SUPPLY AND GRAND CIRCUIT
Perform the trouble diagnosis of power supply and ground circuit. Refer to
.
Is the inspection result normal?
YES
>> Check each harness connector pin terminal for malfunction or disconnection.
NO
>> Repair or replace the error-detected parts.
Revision: November 2015
2016 JUKE
DLN-84
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY21B]
HEAVY TIGHT-CORNER BRAKING SYMPTOM OCCURS
HEAVY TIGHT-CORNER BRAKING SYMPTOM OCCURS
Description
INFOID:0000000012199446
Heavy tight-corner braking symptom occurs when the vehicle is driven and the steering wheel is turned fully to
either side after the engine is started.
NOTE:
Light tight-corner braking symptom may occur depending on driving conditions. This is not malfunction.
Diagnosis Procedure
INFOID:0000000012199447
1.
PERFORM ECM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ENGINE”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
(Except for NISMO
(For NISMO RS).
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
.
NO
>> GO TO 3.
3.
CHECK AWD SOLENOID
Perform the trouble diagnosis of the AWD solenoid. Refer to
(Right side).
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the error-detected parts.
4.
CHECK ELECTRIC CONTROLLED COUPLING
1. Turn the ignition switch OFF.
2. Set the transaxle to neutral. Release the parking brake.
3. Lift up the vehicle.
4. Rotate the propeller shaft by hand.
5. Hold rear wheel of right and left lightly.
Does rear wheel rotate?
YES
>> Replace electric controlled coupling for mechanical malfunction (clutch sticking etc.). Refer to
DLN-145, "Removal and Installation"
NO
>> Check each harness connector pin terminal for disconnection.
Revision: November 2015
2016 JUKE
VEHICLE DOES NOT ENTER AWD MODE
DLN-85
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
VEHICLE DOES NOT ENTER AWD MODE
Description
INFOID:0000000012199448
Vehicle does not enter 4-wheel drive mode even though AWD warning lamp turned to OFF.
Diagnosis Procedure
INFOID:0000000012199449
1.
CHECK AWD WARNING LAMP
Turn the ignition switch ON.
CAUTION:
Never start the engine.
Does AWD warning lamp turn ON?
YES
>> GO TO 2.
NO
>> Proceed to
.
2.
CHECK PARKING BRAKE SWITCH SIGNAL
With CONSULT
Check “PKB SW” in “DATA MONITOR” for “ALL MODE AWD/4WD”.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Proceed to
BRC-129, "Diagnosis Procedure"
3.
CRUISE TEST
Drive the vehicle for a period of time.
Does any symptom occur?
YES
>> Replace electric controlled coupling for mechanical malfunction (mechanical engagement of
clutch is not possible). Refer to
DLN-145, "Removal and Installation"
NO
>> Check each harness connector pin terminal for disconnection.
Monitor Item
Condition
Status
PKB SW
When the parking brake switch is operation.
On
When the parking brake switch is not operation.
Off
Revision: November 2015
2016 JUKE
DLN-86
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY21B]
AWD WARNING LAMP BLINKS QUICKLY
AWD WARNING LAMP BLINKS QUICKLY
Description
INFOID:0000000012199450
While driving, AWD warning lamp blinks 2 times in 1 second and it turns OFF after 1 minute.
NOTE:
• This symptom protects drivetrain parts when a heavy load is applied to the electric controlled coupling and
multiple disc clutch temperature increases. Also, optional distribution of torque sometimes becomes rigid
before lamp blinks quickly. Both cases are not malfunction. Refer to
.
• When this symptom occurs, stop vehicle and allow it to idle for some times. Blinking will stop and system will
be restored.
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст