Nissan Juke (2016 year). Service Repair Manual — part 122
DLK-158
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse TORX bolt. Always replace it with a new one when it is removed.
• Check door open/close, lock/unlock operation after installation.
• Check door lock cable is properly engaged with outside handle bracket.
• Check door lock assembly for poor lubrication. Apply body
grease to door lock if necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000012196736
REMOVAL
1. Remove front door finisher. Refer to
INT-13, "Removal and Installation"
2. Remove inside handle mounting bolt (A).
3. Disengage inside handle (1) from door panel (2) while sliding
inside handle toward vehicle rear, and then separate inside han-
dle.
4. Disengage inside handle cable (3) and lock knob cable (2), and
then remove inside handle (1).
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000012196737
REMOVAL
1. Fully close the front door glass.
2. Remove front door finisher. Refer to
INT-13, "Removal and Installation"
: Grease up point
JMKIA5892ZZ
: Vehicle front
JMKIA5884ZZ
JMKIA5885ZZ
Revision: November 2015
2016 JUKE
FRONT DOOR LOCK
DLK-159
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3. Remove sealing screen.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
4. Disengage lock holder (1), and then separate key rod (3) from
door lock assembly (2).(Driver side)
5. Disconnect harness connector of door antenna (1) and door
request switch (2) and remove harness clamp (3).
6. Remove grommet (1) of door side. Loosen, through grommet
hole, TORX bolt (2) that fixes door lock cylinder. (For passenger
side, TORX bolt fixes outside handle escutcheon.)
7. While pulling outside handle, remove door key cylinder assem-
bly (diver side) or outside handle escutcheon (passenger side).
JMKIA5886ZZ
: Vehicle front
JMKIA5887ZZ
JMKIA5888ZZ
JMKIA0560ZZ
Revision: November 2015
2016 JUKE
DLK-160
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
8. While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
9. Remove front gasket (1) and rear gasket (2).
10. Slide outside handle bracket toward rear of vehicle to remove.
11. Disconnect outside handle cable (1) from outside handle bracket
(2).
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• When installing key rod, rotate key rod holder until a click is felt.
• Check that door lock cables are normally engaged with inside handle and outside handle.
• After installation, check door open/close, and lock/unlock operation.
JMKIA0524ZZ
: Vehicle front
JMKIA5889ZZ
: Vehicle front
JMKIA5890ZZ
JMKIA5891ZZ
Revision: November 2015
2016 JUKE
REAR DOOR LOCK
DLK-161
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REAR DOOR LOCK
Exploded View
INFOID:0000000012196738
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000012196739
REMOVAL
1. Remove rear door glass and rear door lower sash (rear). Refer to
GW-21, "Removal and Installation"
.
2. Remove inside handle. Refer to
DLK-162, "INSIDE HANDLE : Removal and Installation"
.
3. Remove outside handle. Refer to
DLK-162, "OUTSIDE HANDLE : Removal and Installation"
.
4. Remove door lock assembly TORX bolts.
5. Disconnect door lock actuator connector, and then remove door lock assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse TORX bolt. Always replace it with a new one when it is removed.
• Check door open/close, lock/unlock operation after installation.
1.
Outside handle assembly
2.
Rear door sealing screen
3.
Door lock assembly
4.
TORX bolt
5.
Inside handle
: Clip
: Pawl
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Body grease
JMKIA5893GB
Revision: November 2015
2016 JUKE
DLK-162
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
• Check door lock assembly for poor lubrication. Apply body
grease to door lock if necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000012196740
REMOVAL
1. Remove rear door finisher. Refer to
INT-16, "Removal and Installation"
.
2. Remove upper side of sealing screen.
NOTE:
Cut the butyl tape so that some parts of the butyl tape do not remain on the sealing screen, if the sealing
screen is reused.
3. Remove inside handle mounting bolt (A).
4. Disengage inside handle (1) from door panel (2) while sliding
inside handle toward vehicle rear, and then separate inside han-
dle.
5. Disengage inside handle cable (3) and lock knob cable (2), and
then remove inside handle (1).
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000012196741
REMOVAL
1. Remove rear door finisher and rear door corner cover inner. Refer to
INT-16, "Removal and Installation"
2. Remove rear door sealing screen.
: Grease up point
JMKIA5892ZZ
: Vehicle front
JMKIA5884ZZ
JMKIA5885ZZ
Revision: November 2015
2016 JUKE
REAR DOOR LOCK
DLK-163
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3. Rotate stopper (1) upward.
4. Disengage outside handle cable (2), and then remove outside
handle cable from outside handle assembly (3).
5. Remove outside handle assembly mounting bolts (A).
6. Disengage mounting clips using a remover tool (A), and then
remove outside handle assembly.
CAUTION:
Apply protective tape (B) on the door panel to protect the
painted surface from damage.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse rear door sealing screen. Always replace it with a new one when it is removed.
When installing rear door sealing screen, install it according to the following procedure.
- Put lower portion of rear door sealing screen (1) into inside of
door panel (2).
- Perform positioning according to the following procedure,
and then install rear door sealing screen.
• Align upper portion of rear door sealing screen to hole (A) of
door panel as shown in the figure.
• Align hole of rear door sealing screen to edge (B) of door
panel as shown in the figure.
• Be careful to position outside handle cable normally when installing it. For details, refer to
.
• Check door open/close, lock/unlock operation after installation.
JMKIA5894ZZ
JMKIA5895ZZ
: Clip
JMKIA5896ZZ
JMKIA5897ZZ
Revision: November 2015
2016 JUKE
DLK-164
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR LOCK
BACK DOOR LOCK
Exploded View
INFOID:0000000012196742
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000012196743
REMOVAL
1. Remove the back door lower finisher. Refer to
INT-39, "BACK DOOR LOWER FINISHER : Removal and
.
2. Remove back door lock assembly mounting bolts.
3. Disconnect back door lock connector, and then remove back door lock assembly.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
After installation, check back door open/close, and lock/unlock operation.
EMERGENCY LEVER
EMERGENCY LEVER : Unlock procedures
INFOID:0000000012196744
UNLOCK PROCEDURES
NOTE:
If back door lock cannot be unlocked due to a malfunction or battery discharge, follow the procedures to
unlock back door.
1. Remove emergency lid. Refer to
INT-40, "EMERGENCY LID : Removal and Installation"
.
1.
Back door lock assembly
2.
TORX bolt
3.
Back door striker
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Body grease
JMKIA5714GB
Revision: November 2015
2016 JUKE
BACK DOOR LOCK
DLK-165
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2. From inside the vehicle, rotate emergency lever toward lower
direction and unlock.
JMKIA5616ZZ
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст