Nissan Juke (2016 year). Service Repair Manual — part 19
AV-140
< DTC/CIRCUIT DIAGNOSIS >
[AUDIO WITH NAVIGATION]
U111D SIDE CAMERA LH IMAGE SIGNAL CIRCUIT
U111D SIDE CAMERA LH IMAGE SIGNAL CIRCUIT
DTC Logic
INFOID:0000000012202545
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn the ignition switch ON.
2. Shift the selector lever to “R” position.
3. Perform “All DTC Reading” with CONSULT.
4. Check if the “U111D” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.
Is “U111D” detected as the current malfunction?
YES
>> Refer to
.
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
.
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012202546
1.
CHECK CONTINUITY SIDE CAMERA LH POWER SUPPLY AND GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit connector and door mirror (driver side) connector.
3. Check continuity between around view monitor control unit harness connector and door mirror (driver
side) harness connector.
4. Check continuity between around view monitor control unit harness connector and ground.
Is inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK VOLTAGE SIDE CAMERA LH POWER SUPPLY
1. Connect around view monitor control unit connector and door mirror (driver side) connector.
2. Turn ignition switch ON.
3. Check voltage between around view monitor control unit harness connector and ground.
DTC
Trouble diagnosis name
DTC detecting condition
Possible causes
U111D
SIDE CAMERA LH IM-
AGE SIGNAL
Camera image signal circuit is open or shorted.
• Camera image signal circuit be-
tween side camera LH and around
view monitor control unit
• Around view monitor control unit
• Side camera LH
Around view monitor control
unit
Door mirror (driver side)
Continuity
Connector
Terminals
Connector
Terminals
M98
13
D30
6
Existed
14
14
Around view monitor control
unit
Ground
Continuity
Connector
Terminal
M98
14
Not existed
Revision: November 2015
2016 JUKE
AV
U111D SIDE CAMERA LH IMAGE SIGNAL CIRCUIT
AV-141
< DTC/CIRCUIT DIAGNOSIS >
[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Is inspection result normal?
YES
>> GO TO 3.
NO
>> Replace around view monitor control unit. Refer to
AV-190, "Removal and Installation"
3.
CHECK CONTINUITY CAMERA IMAGE SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit connector and door mirror (driver side) connector.
3. Check continuity between around view monitor control unit harness connector and door mirror (driver
side) harness connector.
4. Check continuity between around view monitor control unit harness connector and ground.
Is inspection result normal?
YES
>> GO TO 4.
NO
>> Repair harness or connector.
4.
CHECK CAMERA IMAGE SIGNAL
1. Connect around view monitor control unit connector and door mirror (driver side) connector.
2. Turn ignition switch ON.
3. Check signal between around view monitor control unit harness connector terminals.
Is inspection result normal?
Terminal
Condition
Standard
Reference voltage
(Approx.)
(+)
(
−
)
Around view monitor control unit
Connector
Terminal
Connector
Terminal
M98
14
M98
13
“CAMERA” switch
(around view moni-
tor switch) is ON or
shift position is “R”.
3.5 V or more
6.0 V
Around view monitor control
unit
Door mirror (driver side)
Continuity
Connector
Terminals
Connector
Terminals
M98
15
D30
7
Existed
16
15
Around view monitor control
unit
Ground
Continuity
Connector
Terminals
M98
15
Not existed
16
Terminal
Condition
Standard
Reference value
(+)
(
−
)
Around view monitor control unit
Connector
Terminal
Connector
Terminal
M98
16
M98
15
Shift position is in
“R”.
Waveform accord-
ing to camera image
is input.
JSNIA0834GB
Revision: November 2015
2016 JUKE
AV-142
< DTC/CIRCUIT DIAGNOSIS >
[AUDIO WITH NAVIGATION]
U111D SIDE CAMERA LH IMAGE SIGNAL CIRCUIT
YES
>> Replace around view monitor control unit. Refer to
AV-190, "Removal and Installation"
NO
>> Replace side camera LH. Refer to
AV-193, "Removal and Installation"
.
Revision: November 2015
2016 JUKE
AV
U1200 NAVI CONTROL UNIT
AV-143
< DTC/CIRCUIT DIAGNOSIS >
[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U1200 NAVI CONTROL UNIT
DTC Logic
INFOID:0000000012202547
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible cause
U1200
Cont Unit
(Control unit FLASH-ROM)
NAVI control unit malfunction is detected.
Replace the NAVI control unit if the mal-
function occurs constantly.
Refer to
AV-182, "Removal and Installa-
.
Revision: November 2015
2016 JUKE
AV-144
< DTC/CIRCUIT DIAGNOSIS >
[AUDIO WITH NAVIGATION]
U1217 NAVI CONTROL UNIT
U1217 NAVI CONTROL UNIT
DTC Logic
INFOID:0000000012202548
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible cause
U1217
BLUETOOTH MODULE
(Bluetooth module connec-
tion)
NAVI control unit malfunction is detected.
Replace the NAVI control unit if the mal-
function occurs constantly.
Refer to
AV-182, "Removal and Installa-
.
Revision: November 2015
2016 JUKE
AV
U1229 NAVI CONTROL UNIT
AV-145
< DTC/CIRCUIT DIAGNOSIS >
[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U1229 NAVI CONTROL UNIT
DTC Logic
INFOID:0000000012202549
DTC DETECTION LOGIC
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible cause
U1229
iPod CERTIFICATION
(iPod certification error)
NAVI control unit malfunction is detected.
Replace the NAVI control unit if the mal-
function occurs constantly.
Refer to
AV-182, "Removal and Installa-
.
Revision: November 2015
2016 JUKE
AV-146
< DTC/CIRCUIT DIAGNOSIS >
[AUDIO WITH NAVIGATION]
U1232 STEERING ANGLE SENSOR
U1232 STEERING ANGLE SENSOR
DTC Logic
INFOID:0000000012202550
Diagnosis Procedure
INFOID:0000000012202551
1.
REGISTER THE NEUTRAL POSITION OF THE STEERING ANGLE SENSOR
1. Turn the ignition switch ON.
2. Perform registration of the neutral position of the steering angle sensor. Refer to
3. Check “Self Diagnostic Result” of “AVM” with CONSULT.
Is “U1232” detected as the current malfunction?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
CHECK STEERING ANGLE SENSOR
Check steering angle sensor. Refer to
Is the inspection result normal?
YES
>> Replace the around view monitor control unit. Refer to
AV-190, "Removal and Installation"
NO
>> Repair or replace malfunctioning parts.
DTC
Trouble diagnosis name
DTC detecting condition
Possible causes
U1232
ST ANGLE SEN CALIB
The neutral position registration of the steering angle sen-
sor can not finish.
• Steering angle sensor
• Around view monitor control unit
Revision: November 2015
2016 JUKE
AV
U1244 GPS ANTENNA
AV-147
< DTC/CIRCUIT DIAGNOSIS >
[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U1244 GPS ANTENNA
DTC Logic
INFOID:0000000012202552
Diagnosis Procedure
INFOID:0000000012202553
1.
GPS ANTENNA CHECK
Visually check GPS antenna and antenna feeder.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair malfunctioning parts.
2.
CHECK NAVI CONTROL UNIT VOLTAGE
1. Disconnect GPS antenna connector.
2. Turn ignition switch ON.
3. Check voltage between NAVI control unit and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace NAVI control unit. Refer to
AV-182, "Removal and Installation"
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible cause
U1244
GPS ANTENNA CONN
(GPS antenna connection)
GPS antenna connection malfunction is detect-
ed.
• GPS antenna connector connection
• GPS antenna
(+)
(
−
)
Standard
Voltage
(Approx.)
NAVI control unit
Terminal
54
Ground
—
5.0 V
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст