Nissan Juke (2016 year). Service Repair Manual — part 221
NORMAL OPERATING CONDITION
EC-583
< SYMPTOM DIAGNOSIS >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
NORMAL OPERATING CONDITION
Description
INFOID:0000000012198128
FUEL CUT CONTROL (AT NO LOAD AND HIGH ENGINE SPEED)
If the engine speed is above 2,500 rpm under no load (for example, the selector lever position is neutral and
engine speed is over 2,500 rpm) fuel will be cut off after some time. The exact time when the fuel is cut off var-
ies based on engine speed.
Fuel cut will be operated until the engine speed reaches 2,000 rpm, then fuel cut will be cancelled.
NOTE:
This function is different from deceleration control listed under direct injection gasoline system,
"DIRECT INJECTION GASOLINE SYSTEM : System Description"
Revision: November 2015
2016 JUKE
EC-584
< PERIODIC MAINTENANCE >
[MR FOR NISMO RS MODELS]
IDLE SPEED
PERIODIC MAINTENANCE
IDLE SPEED
Inspection
INFOID:0000000012198129
1.
CHECK IDLE SPEED
With CONSULT
Check idle speed in “DATA MONITOR” mode of “ENGINE” using CONSULT.
With GST
Check idle speed with Service $01 of GST.
>> INSPECTION END
Revision: November 2015
2016 JUKE
IGNITION TIMING
EC-585
< PERIODIC MAINTENANCE >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
IGNITION TIMING
Inspection
INFOID:0000000012198130
1.
CHECK IGNITION TIMING
1. Attach timing light to the ignition coil No.1 harness.
2. Check ignition timing.
>> INSPECTION END
1
: Timing indicator
PBIB3263E
Revision: November 2015
2016 JUKE
EC-586
< PERIODIC MAINTENANCE >
[MR FOR NISMO RS MODELS]
EVAPORATIVE EMISSION SYSTEM
EVAPORATIVE EMISSION SYSTEM
Inspection
INFOID:0000000012198131
EVAP CANISTER
1.
CHECK EVAP CANISTER
1. Block port (B).
2. Blow air into port (A) and check that it flows freely out of port (C).
3. Release blocked port (B).
4. Apply vacuum pressure to port (B) and check that vacuum pres-
sure exists at the ports (A) and (C).
5. Block port (A) and (B).
6. Apply pressure to port (C) and check that there is no leakage.
>> INSPECTION END
PBIB1212E
Revision: November 2015
2016 JUKE
EVAP LEAK CHECK
EC-587
< PERIODIC MAINTENANCE >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
EVAP LEAK CHECK
Inspection
INFOID:0000000012198132
CAUTION:
• Do not use compressed air or a high pressure pump.
• Do not exceed 4.12 kPa (0.042 kg/cm
2
, 0.6 psi) of pressure in EVAP system.
NOTE:
• Do not start engine.
• Improper installation of EVAP service port adapter [commercial service tool: (J-41413-OBD)] to the EVAP
service port may cause a leak.
1.
EVAP LEAK CHECK
With CONSULT
1. Install EVAP service port adapter [commercial service tool: (J-
41413-OBD)] and pressure pump to EVAP service port.
2. Turn ignition switch ON.
3. Select the “EVAP SYSTEM CLOSE” in “WORK SUPPORT” mode of “ENGINE” using CONSULT.
4. Touch “START”. A bar graph (Pressure indicating display) will appear on the screen.
5. Apply positive pressure to the EVAP system until the pressure indicator reaches the middle of the bar
graph.
6. Remove EVAP service port adapter [commercial service tool: (J-41413-OBD)] and hose with pressure
pump.
7. Locate the leak using a leak detector [commercial service tool:
(J-41416)]. Refer to
EC-66, "EVAPORATIVE EMISSION SYS-
.
Without CONSULT
1. Install EVAP service port adapter [commercial service tool: (J-
41413-OBD)] and pressure pump to EVAP service port.
SEF462UA
SEF200U
SEF462UA
Revision: November 2015
2016 JUKE
EC-588
< PERIODIC MAINTENANCE >
[MR FOR NISMO RS MODELS]
EVAP LEAK CHECK
2. Apply battery voltage between the terminals of EVAP canister vent control valve to make a closed EVAP
system.
3. To locate the leak, deliver positive pressure to the EVAP system until pressure gauge points reach 1.38 to
2.76 kPa (0.014 to 0.028 kg/cm
2
, 0.2 to 0.4 psi).
4. Remove EVAP service port adapter [commercial service tool: (J-41413-OBD)] and hose with pressure
pump.
5. Locate the leak using a leak detector [commercial service tool:
(J-41416)]. Refer to
EC-66, "EVAPORATIVE EMISSION SYS-
.
>> INSPECTION END
SEF200U
Revision: November 2015
2016 JUKE
POSITIVE CRANKCASE VENTILATION
EC-589
< PERIODIC MAINTENANCE >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
POSITIVE CRANKCASE VENTILATION
Inspection
INFOID:0000000012198133
1.
CHECK PCV VALVE
With engine running at idle, remove PCV valve from rocker cover. A
properly working valve makes a hissing noise as air passes through
it. A strong vacuum should be felt immediately when a finger is
placed over valve inlet.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace PCV valve. Refer to
.
PBIB1589E
Revision: November 2015
2016 JUKE
EC-590
< REMOVAL AND INSTALLATION >
[MR FOR NISMO RS MODELS]
ECM
REMOVAL AND INSTALLATION
ECM
Removal and Installation
INFOID:0000000012198134
CAUTION:
Perform ADDITIONAL SERVICE WHEN REPLACING ECM. Refer to
REMOVAL
1. Remove fusible link bracket. Keep a service area.
2. Disconnect ECM harness connectors. Refer to
.
3. Remove ECM mounting nuts, and then remove ECM.
INSTALLATION
Install in the reverse order of removal.
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст