Nissan Juke (2016 year). Service Repair Manual — part 393
FRONT DRIVE SHAFT
FAX-85
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
CAUTION:
Never place drive shaft joint at an extreme angle when removing drive shaft. Also be careful not to
overextend slide joint.
13. Remove heat insulator.
14. Remove support bearing bracket.
INSTALLATION
Note the following, and install in the reverse order of removal.
Left Side
• Always replace differential side oil seal with new one when installing drive shaft. Refer to
• Place the protector (A) [SST:KV38107900 ( — )] onto transaxle
assembly to prevent damage to the differential side oil seal while
inserting drive shaft. Slide drive shaft sliding joint and tap with a
hammer to install securely.
CAUTION:
• Check that circular clip is completely engaged.
• Never reuse circular clip.
• Never reuse differential side oil seal.
• Clean the matching surface of wheel hub lock nut and wheel hub assembly.
CAUTION:
Never apply lubricating oil to these matching surface.
• Clean the matching surface of drive shaft and wheel hub assembly.
And then apply paste [service parts (440037S000)] to surface (A)
of joint sub-assembly of drive shaft.
CAUTION:
Apply paste to cover entire flat surface of joint sub-assembly
of drive shaft.
• Use the following torque range for tightening the wheel hub lock nut.
CAUTION:
• Since the drive shaft is assembled by press-fitting, use the tightening torque range for the wheel
hub lock nut.
• Be sure to use torque wrench to tighten the wheel hub lock nut. Never use a power tool.
• Never reuse wheel hub lock nut.
NOTE:
Wheel hub lock nut tightening torque does not over torque for avoiding axle noise, and does not less than
torque for avoiding looseness.
• Align the matching marks that have been made during removal when reusing the disc rotor.
JPDIF0023ZZ
Amount paste
: 1.0 – 3.0 g (0.04 – 0.10 oz)
JSDIA2844ZZ
: 180 – 185 N·m (18.4 – 18.8 kg-m, 133 – 136 ft-lb)
Revision: November 2015
2016 JUKE
FAX-86
< REMOVAL AND INSTALLATION >
[TYPE 2]
FRONT DRIVE SHAFT
• When installing a cotter pin (1) and adjusting cap (2), securely
bend the basal portion to prevent rattles.
CAUTION:
Never reuse cotter pin.
• Perform the final tightening of each of parts under unladen conditions, which were removed when removing
wheel hub assembly and steering knuckle.
• Perform inspection after installation. Refer to
Right Side
• Always replace differential side oil seal with new one when installing drive shaft. Refer to
• Install support bearing bracket (1) in following procedure,
- Temporarily tighten mounting bolts (A), (B), (C), then tighten them
to specified torque.
- Set plate (2) so that notch (D) becomes upper side. Temporarily
tighten mounting bolts (E), (F), then tighten them to specified
torque.
CAUTION:
Never reuse plate.
• Place the protector (A) [SST:KV38107900 ( — )] onto transaxle
assembly to prevent damage to the differential side oil seal while
inserting drive shaft. Slide drive shaft sliding joint and tap with a
hammer to install securely.
CAUTION:
Never reuse differential oil seal.
• To install mounting nuts of the heat insulator (1), temporarily
tighten them in numerical order shown in the figure and tighten
them to the specified torque.
• Clean the matching surface of wheel hub lock nut and wheel hub assembly.
CAUTION:
Never apply lubricating oil to these matching surface.
JPDIF0295ZZ
JSDIA2132ZZ
JSDIA6354ZZ
JPDIF0312ZZ
Revision: November 2015
2016 JUKE
FRONT DRIVE SHAFT
FAX-87
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
• Clean the matching surface of drive shaft and wheel hub assembly.
And then apply paste [service parts (440037S000)] to surface (A)
of joint sub-assembly of drive shaft.
CAUTION:
Apply paste to cover entire flat surface of joint sub-assembly
of drive shaft.
• Use the following torque range for tightening the wheel hub lock nut.
CAUTION:
• Since the drive shaft is assembled by press-fitting, use the tightening torque range for the wheel
hub lock nut.
• Be sure to use torque wrench to tighten the wheel hub lock nut. Never use a power tool.
• Never reuse wheel hub lock nut.
NOTE:
Wheel hub lock nut tightening torque does not over torque for avoiding axle noise, and does not less than
torque for avoiding looseness.
• Align the matching marks that have been made during removal when reusing the disc rotor.
• When installing a cotter pin (1) and adjusting cap (2), securely
bend the basal portion to prevent rattles.
CAUTION:
Never reuse cotter pin.
• Perform the final tightening of each of parts under unladen conditions, which were removed when removing
wheel hub assembly and steering knuckle.
• Perform inspection after installation. Refer to
.
2WD : Disassembly and Assembly
INFOID:0000000012201562
DISASSEMBLY
Wheel Side
1. Fix shaft with a vise.
CAUTION:
Protect shaft using aluminum or copper plates when fixing with a vise.
2. Remove boot bands, and then remove boot from joint sub-assembly.
Amount paste
: 1.0 – 3.0 g (0.04 – 0.10 oz)
JSDIA2844ZZ
: 180 – 185 N·m (18.4 – 18.8 kg-m, 133 – 136 ft-lb)
JPDIF0295ZZ
Revision: November 2015
2016 JUKE
FAX-88
< REMOVAL AND INSTALLATION >
[TYPE 2]
FRONT DRIVE SHAFT
3. Screw drive shaft puller (A) (commercial service tool) into joint
sub-assembly screw part to a length of 30 mm (1.18 in) or more.
Support drive shaft with one hand and pull out joint sub-assem-
bly from shaft.
CAUTION:
• Align drive shaft puller and drive shaft and remove them
by pulling firmly and uniformly.
• If joint sub-assembly cannot be removed after five or
more unsuccessful attempts, replace shaft and joint sub
assembly as a set.
4. Remove circular clip from shaft.
5. Remove boot from shaft.
Transaxle Side (Left Drive Shaft)
1. Fix shaft with a vise.
CAUTION:
Protect shaft using aluminum or copper plates when fixing with a vise.
2. Remove wheel side boot from joint sub-assembly. Refer to
FAX-83, "2WD : Removal and Installation"
3. Remove dynamic damper as per the following instructions:
a. Remove damper band.
b. Remove dynamic damper from housing assembly.
4. Remove boot bands, then remove boot from housing assembly.
5. Remove circular clip from housing assembly.
6. Remove dust shield from housing assembly.
Transaxle Side (Right Drive Shaft)
1. Fix shaft with a vise.
CAUTION:
Protect shaft using aluminum or copper plates when fixing with a vise.
2. Remove wheel side boot from joint sub-assembly. Refer to
FAX-83, "2WD : Removal and Installation"
3. Remove dynamic damper as per the following instructions:
a. Remove damper band.
b. Remove dynamic damper from housing assembly.
4. Remove boot bands, then remove boot from housing assembly.
5. Remove support bearing, follow the procedure described below.
a. Remove dust shield from housing.
JPDIG0151ZZ
YAX002
Revision: November 2015
2016 JUKE
FRONT DRIVE SHAFT
FAX-89
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
b. Remove snap ring (1).
c. Press out support bearing from housing.
d. Remove dust shield from housing.
ASSEMBLY
Wheel Side
1. Clean the old grease on joint sub-assembly with paper waste.
2. Fill serration slot joint sub-assembly (1) with NISSAN genuine
grease or equivalent until the serration slot and ball groove
become full to the brim.
CAUTION:
After applying grease, use a paper waste to wipe off old
grease that has oozed out.
3. Install boot and boot bands to shaft.
CAUTION:
• Wrap serration on shaft with tape (A) to protect the boot
from damage.
• Never reuse boot and boot band.
4. Remove the tape wrapped around the serration on shaft.
JPDIF0106ZZ
YAX004
JPDIF0008ZZ
JPDIF0009ZZ
Revision: November 2015
2016 JUKE
FAX-90
< REMOVAL AND INSTALLATION >
[TYPE 2]
FRONT DRIVE SHAFT
5. Position the circular clip (1) on groove at the shaft edge.
CAUTION:
Never reuse circular clip.
NOTE:
Drive joint inserter is recommended when installing circular clip.
6. Align both center axles of the shaft edge and joint sub-assembly. Then assemble shaft with joint sub-
assembly holding circular clip.
7. Install joint sub-assembly to shaft using plastic hammer.
CAUTION:
• Check circular clip is properly positioned on groove of the
joint sub-assembly.
• Confirm that joint sub-assembly is correctly engaged
while rotating drive shaft.
8. Apply the specified amount of grease into the boot inside from large diameter side of boot.
9. Install the boot securely into grooves (indicated by “*” marks)
shown in the figure.
CAUTION:
If grease adheres to the boot mounting surface (indicated
by “*” marks) on the shaft or joint sub-assembly, boot may
be removed. Remove all grease from the boot mounting
surface.
10. To prevent the deformation of the boot, adjust the boot installation length (L) to the specified value shown
below by inserting the suitable tool into inside of the boot from the large diameter side of the boot and dis-
charging the inside air.
CAUTION:
• If the boot installation length exceeds the standard, it may cause breakage of the boot.
• Be careful not to touch the inside of the boot with a tip of tool.
JPDIF0305ZZ
RAC0049D
Grease amount
: Refer to
.
JSDIA2261ZZ
L : Refer to
.
Revision: November 2015
2016 JUKE
FRONT DRIVE SHAFT
FAX-91
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
11. Secure the large and small ends of the boot with boot bands
using the boot band crimping tool (A) [SST:KV40107300 ( —
)].
CAUTION:
• Never reuse boot band.
• Secure boot band so that dimension (M) meets the speci-
fication as shown in the figure.
12. Check that displacement does not occur when boot is rotated with the joint sub-assembly and shaft fixed.
CAUTION:
• Reinstall them using boot bands when boot installation positions become incorrect.
• Never reuse boot band.
Transaxle Side (Left Drive Shaft)
1. Clean the old grease on housing assembly with paper waste.
2. Install dust shield to housing assembly.
CAUTION:
Never reuse dust shield.
3. Install circular clip to housing.
CAUTION:
Never reuse circular clip.
4. Install boot and boot bands to housing assembly.
CAUTION:
• Wrap serration on housing assembly with tape (A) to pro-
tect the boot from damage.
• Never reuse boot and boot band.
5. Remove the tape wrapped around the serration on shaft.
6. Apply NISSAN genuine grease (refer to parts catalog) to housing assembly.
JPDIF0012ZZ
Dimension (M)
: 2.0 – 3.0 mm (0.079 – 0.118 in)
DSF0047D
JSDIA2232ZZ
Grease amount
: Refer to
.
Revision: November 2015
2016 JUKE
FAX-92
< REMOVAL AND INSTALLATION >
[TYPE 2]
FRONT DRIVE SHAFT
7. Install the boot securely into grooves (indicated by “*” marks)
shown in the figure.
CAUTION:
If grease adheres to the boot mounting surface (indicated
by “*” marks) on the shaft or housing assembly, boot may
be removed. Remove all grease from the boot mounting
surface.
8. To prevent the deformation of the boot, adjust the boot installation length to the value shown below (L) by
inserting the suitable tool into the inside of boot from the large diameter side of boot and discharging
inside air.
CAUTION:
• If the boot installation length exceeds the standard, it may cause breakage of the boot.
• Be careful not to touch the inside of the boot with the tip of tool.
9. Install boot bands securely.
CAUTION:
Never reuse boot bands.
a. Put boot band in the groove on drive shaft boot. Then fit pawls
(
) into holes to temporary installation.
NOTE:
For the large diameter side, fit projection (A) and guide slit (B) at
first.
b. Pinch projection on the band with suitable pliers to tighten band.
c.
Insert the tip of band into the lower part of pawl (marked with
dotted circle) as shown in the figure.
10. Check that displacement does not occur when boot is rotated with the housing assembly fixed.
CAUTION:
• If displacement occurs, reinstall band.
• Never reuse boot band.
11. Install dynamic damper, follow the procedure described below.
a. Install dynamic damper to shaft.
JSDIA2063ZZ
L
: Refer to
JPDIF0157ZZ
JPDIF0158ZZ
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст