Nissan Juke (2016 year). Service Repair Manual — part 557
FRONT SEAT
SE-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
1. Cut harness clip (A) and disengage side air bag harness connector (B), harness clip (C).
2. Remove lifter lever.
a. Disengage lifter lever cap fixing pawls, and then remove lifter
lever cap.
b. Remove lifter lever fixing screws (A), and then remove lifter
lever.
3. Remove seat cushion finisher fixing screws (A), and then
remove seat cushion finisher.
Passenger side
Driver side
: Clip
JMJIB0213ZZ
: Pawl
JMJIB0110ZZ
JMJIB0111ZZ
JMJIB0112ZZ
Revision: November 2015
2016 JUKE
SE-24
< REMOVAL AND INSTALLATION >
FRONT SEAT
4. Remove reclining device cover fixing screw (A), and then
remove reclining device cover while disengage reclining device
cover fixing pawls.
5. Remove seatback assembly fixing screws (A), and then remove
seatback assembly.
NOTE:
• Disengage reclining knob fixing pawl, and then remove reclining
knob.
ASSEMBLY
Note the following items, and then assemble in the reverse order of disassembly.
Without RECARO seat model
CAUTION:
• For hog ring that is removed or crimped unsuccessfully, fix it by using a new hog ring. (Never reuse
hog ring.)
• Always install the hog rings in position.
With RECARO seat model
CAUTION:
• When installing seatback assembly, temporary tighten all
seatback assembly fixing bolts, and then tighten fixing bolts
according to the numerical order 1
→
4 indicated by as shown
in the figure, starting from front right fixing bolt.
: Pawl
JMJIB0113ZZ
JMJIB0114ZZ
: Pawl
JMJIB0115ZZ
JMJIB0116ZZ
Revision: November 2015
2016 JUKE
FRONT SEAT
SE-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
SEAT CUSHION
SEAT CUSHION : Disassembly and Assembly
INFOID:0000000012196882
DISASSEMBLY
Without RECARO seat model
CAUTION:
For models with heater seat, always replace heater seat as a seat cushion assembly without disas-
sembling trim and pad.
1. Remove seat cushion outer finisher.
1. Disengage pawls and remove lifter lever knob cap (1).
(Driver seat only)
2. Remove fixing screws and remove lifter lever knob (2).
(Driver seat only)
3. Disengage pawl using a screwdriver while pulling reclining
lever knob. Slide reclining lever knob toward seat front and
remove it.
4. Pull seat cushion outer finisher toward seat front. Disengage pawls and metal clips. Slide seat cush-
ion outer finisher toward seat front. Remove seat cushion outer finisher.
2. Remove harness installed in the lower portion of seat cushion.
: Pawl
JMJIA4592ZZ
: Pawl
JMJIA4593ZZ
1.
Seat cushion outer finisher
(Driver seat)
2.
Seat cushion outer finisher
(Passenger seat)
: Pawl
: Metal clip
JMJIA4594ZZ
Revision: November 2015
2016 JUKE
SE-26
< REMOVAL AND INSTALLATION >
FRONT SEAT
1. Disconnect seat cushion heater unit harness connectors (A)
and (B). (with heater seat only)
2. Remove seat cushion heater unit harness connector fixing
clip and harness fixing clamps (C). (with heater seat only)
3. Remove seat belt buckle harness connector fixing clip (D)
and harness fixing clamps (E).
3. Remove seat cushion inner finisher.
1. Remove harness fixing clamp of seat belt buckle installed on seat frame & adjuster assembly.
2. Remove seat belt buckle mounting anchor bolt, and then remove seat belt buckle from seat frame
&adjuster assembly.
3. Pull seat cushion inner finisher forward. Disengage pawls
and metal clips.
4. Remove seat cushion retainer from seat frame & adjuster assembly. Remove seat cushion trim and seat
cushion pad.
5. Remove hog rings, and separate the seat cushion trim and seat cushion pad. (without heater seat only)
CAUTION:
Before performing separating operation, check the installation position of hog rings.
6. Remove seat cushion silencer from seat frame & adjuster assembly.
7. Remove seatback trim and seatback pad from seat frame & adjuster assembly.
SE-21, "SEATBACK : Disassembly and Assembly"
.
8. Remove reclining device cover.
• Remove fixing screw, and then remove reclining device outer cover (front and rear).
• Remove fixing screw, and then remove reclining device inner cover (front and rear).
9. Remove following parts from seat frame & adjuster assembly.
• Remove reclining spring.
• Remove fixing screws. Pull outer lower cover toward seat outer. Disengage metal clips. Remove outer
lower cover. (driver seat only)
• Remove fixing screws, and then remove inner lower cover. (driver seat only)
• Remove occupant detection system control unit. Refer to
SR-32, "Removal and Installation"
.
With RECARO seat model
1. Disengage harness clips (A).
: Vehicle front
JMJIA4603ZZ
: Pawl
: Metal clip
JMJIA4595ZZ
JMJIB0214ZZ
Revision: November 2015
2016 JUKE
FRONT SEAT
SE-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
2. Remove seat cushion fixing bolts (A), and then remove seat
cushion.
CAUTION:
As the bolt length differs (the ones on the front are longer),
always confirm the matching between the bolt and the
mounting hole.
3. Remove occupant sensor harness (passenger side only).
a. Cut cable tie (A) and disengage harness clips (B).
b. Remove bracket fixing screws (A), and then remove bracket.
c. Disconnect harness connector, and then remove occupant sensor harness.
4. Remove seat belt buckle. Refer to
SB-9, "SEAT BELT BUCKLE : Removal and Installation"
ASSEMBLY
Without RECARO seat model
Note the following items, and then assemble in the reverse order of disassembly.
CAUTION:
• For hog ring that is removed or crimped unsuccessfully, fix it by using a new hog ring. (Never reuse
hog ring.)
• Always install the hog rings in position.
passenger side
Driver side
: Clip
JMJIB0117ZZ
: Clip
JMJIB0215ZZ
JMJIB0216ZZ
Revision: November 2015
2016 JUKE
SE-28
< REMOVAL AND INSTALLATION >
FRONT SEAT
• When installing seat cushion finisher, always slide seat cush-
ion outer finisher toward seat rear, engage portion (A) of seat
frame & adjuster assembly and portion (B) of seat cushion
outer finisher, and then install pawls and metal clips of seat
cushion outer finisher.
With RECARO seat model
Note the following items, and then assemble in the reverse order of disassembly.
CAUTION:
• Install in the occupant sensor harness fixing clip and cable tie as shown in the figure.
• Install in the as with before removal to prevent cable discon-
nection.
: Vehicle front
JMJIA4612ZZ
: Cable branch point
B
: 50 mm
C
: 50 mm
: Cable branch point
E
: 70 mm
F
: 25 mm
JMJIB0217ZZ
JMJIB0218ZZ
Revision: November 2015
2016 JUKE
REAR SEAT
SE-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
REAR SEAT
Exploded View
INFOID:0000000012196883
2WD models
JMJIA5194GB
1.
Headrest
2.
Headrest holder (free)
3.
Headrest holder (locked)
4.
Seatback trim RH
5.
Seatback pad RH
6.
Seat lock cover RH
Revision: November 2015
2016 JUKE
SE-30
< REMOVAL AND INSTALLATION >
REAR SEAT
7.
Seatback lock knob
8.
Seatback lock knob finisher
9.
Seatback lock assembly RH
10. Side hinge
11. Bush
12. Spacer
13. Lock washer
14. Striker RH
15. Seat cushion hook
16. Seat cushion pad
17. Seat cushion trim
18. Striker LH
19. Seatback lock assembly LH
20. Seat lock cover LH
21. Seatback pad LH
22. Seatback trim LH
23. Seatback silencer LH
24. Seatback silencer RH
25. Seatback tether cover
26. Center seat belt finisher
27. Center hinge
28. Center seat belt
29. Seat belt buckle
30. Seatback frame RH
31. Seatback frame LH
: Pawl
: Metal clip
: N·m (kg-m, ft-lb)
, , , : Indicates that the part is connected at points with same symbol in actual vehicle.
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст