Nissan Juke (2016 year). Service Repair Manual — part 556
SQUEAK AND RATTLE TROUBLE DIAGNOSES
SE-15
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Diagnostic Worksheet
INFOID:0000000012196878
PIIB8740E
Revision: November 2015
2016 JUKE
SE-16
< SYMPTOM DIAGNOSIS >
SQUEAK AND RATTLE TROUBLE DIAGNOSES
PIIB8742E
Revision: November 2015
2016 JUKE
FRONT SEAT
SE-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
REMOVAL AND INSTALLATION
FRONT SEAT
Exploded View
INFOID:0000000012196879
DRIVER SEAT
1.
Headrest
2.
Headrest holder (locked)
3.
Headrest holder (free)
4.
Seatback assembly
(with heater seat only)
5.
Inner lower cover
6.
Seatback trim
(without heater seat only)
JMJIA4582GB
Revision: November 2015
2016 JUKE
SE-18
< REMOVAL AND INSTALLATION >
FRONT SEAT
PASSENGER SEAT
7.
Seatback pad
(without heater seat only)
8.
Seat belt buckle
9.
Anchor bolt
10. Seat cushion inner finisher
11. Reclining device inner cover (front)
12. Reclining device inner cover (rear)
13. TORX bolt
14. Seat cushion trim
(without heater seat only)
15. Seat cushion pad
(without heater seat only)
16. Seat cushion silencer
17. Seat cushion assembly
(with heater seat only)
18. Lifter link
19. Lifter lever knob
20. Lifter lever knob cap
21. Reclining lever knob
22. Seat cushion outer finisher
23. Spring
24. Reclining device outer cover (front)
25. Reclining device outer cover (rear)
26. Outer lower cover
27. Side air bag module
28. Seatback silencer
29. Seat frame & adjuster assembly
: Pawl
: Metal clip
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
, , , , , , , , , : Indicates that the part is connected at points with same symbol in actual vehicle.
Revision: November 2015
2016 JUKE
FRONT SEAT
SE-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
1.
Headrest
2.
Headrest holder (locked)
3.
Headrest holder (free)
4.
Seatback silencer
5.
Side air bag module
6.
Spring
7.
Reclining device outer cover (rear)
8.
Reclining device outer cover (front)
9.
Seat cushion outer finisher
10. Reclining lever knob
11. TORX bolt
12. Seat cushion trim
(without heater seat only)
13. Seat cushion pad
(without heater seat only)
14. Occupant detection system control
unit
15. Seat cushion silencer
16. Seat cushion assembly
(with heater seat only)
17. Anchor bolt
18. Seat belt buckle
19. Seat cushion inner finisher
20. Reclining device inner cover (front)
21. Reclining device inner cover (rear)
JMJIA9479GB
Revision: November 2015
2016 JUKE
SE-20
< REMOVAL AND INSTALLATION >
FRONT SEAT
RECARO SEAT
22. Seatback pad
(without heater seat only)
23. Seatback trim
(without heater seat only)
24. Seatback assembly
(with heater seat only)
25. Seat frame & adjuster assembly
: Pawl
: Metal clip
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
, , , , , , , , , : Indicates that the part is connected at points with same symbol in actual vehicle.
1.
Seatback assembly
2.
Seat cushion
3.
Harness tape
*
4.
Seat belt buckle
5.
Harness clip
6.
Reclining device cover
7.
Seat adjuster assembly
8.
Seat cushion finisher
9.
Lifter lever
JMJIB0222GB
Revision: November 2015
2016 JUKE
FRONT SEAT
SE-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
*: passenger seat only
Removal and Installation
INFOID:0000000012196880
REMOVAL
CAUTION:
Before servicing, disconnect the battery cable from negative terminal or remove the fuse.
1. Remove headrest.
2. Set the seatback vertically.
3. Slide seat to the frontmost position.
4. Remove rear outer mounting TORX bolt.
5. Remove rear inner mounting TORX bolt.
6. Slide seat to the rearmost position.
7. Remove front outer mounting TORX bolt.
8. Remove front inner mounting TORX bolt.
9. Remove seat cushion lower harness connectors and harness fixing clamps.
CAUTION:
Before performing removal operation, check the installation position of harness connectors and
harness fixing clamps.
10. Remove seat from the vehicle.
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• When removing and installing, use shop cloths to protect parts from damage.
• When installing, tighten mounting TORX bolts according to
the numerical order (1, 2, 3, and 4 as shown in the figure),
starting from front inner mounting TORX bolt.
• Always fix the harness fixing clamp in position.
SEATBACK
SEATBACK : Disassembly and Assembly
INFOID:0000000012196881
DISASSEMBLY
Without RECARO seat model
CAUTION:
10. Lifter lever cap
11. Occupant sensor harness
*
12. Reclining knob
13. Frame carpet
: Pawl
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JMJIA4591ZZ
Revision: November 2015
2016 JUKE
SE-22
< REMOVAL AND INSTALLATION >
FRONT SEAT
For models with heater seat, always replace heater seat as a seatback assembly without disassem-
bling trim and pad.
1. Remove seatback retainer installed in the lower portion of seat cushion.
2. Remove harness installed in the lower portion of seat cushion.
1. Disconnect seatback heater unit harness connector
(A).(with heater seat only.)
2. Remove seatback heater unit harness connector fixing clips
and harness fixing clamp (B). (with heater seat only)
3. Disconnect side air bag module harness connector (C).
4. Remove side air bag module harness connector fixing clips
and harness fixing clamp (D).
3. Open seatback fastener (A) and remove seatback retainer (B).
4. Remove side air bag module harness fixing clamps from seat frame & adjuster assembly.
5. Use pincers, etc., to press up pawls as shown by the arrows in
the figure, and remove headrest holder from seatback.
CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
6. Remove side air bag module mounting nuts.
7. Remove seatback trim and seatback pad from seat frame & adjuster assembly.
CAUTION:
Never subject side air bag module to impact by dropping or hitting.
8. Remove side air bag module from seatback pad.
9. Separate the seatback trim and seatback pad. (without heater seat only)
Remove hog rings, and separate the seatback trim and seatback pad.
CAUTION:
Before performing separating operation, check the installation position of hog rings.
10. Remove seatback silencer from seat frame & adjuster assembly.
With RECARO seat model
: Vehicle front
JMJIA4602ZZ
JMJIA4363ZZ
PIIB4084J
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст