Nissan Juke (2016 year). Service Repair Manual — part 685
WT-26
< DTC/CIRCUIT DIAGNOSIS >
C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR
C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR
DTC Logic
INFOID:0000000012201853
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION
With CONSULT
1. Turn the ignition switch ON.
CAUTION:
Never start the engine.
2. Check the tire pressure for all wheels and adjust to the specified value. Refer to
.
CAUTION:
If the tire pressure before adjustment is close to the standard, reduce the tire pressure, and then
with the ignition switch ON, adjust the tire pressure again so that it is within the standard.
3. Perform self-diagnosis in “AIR PRESSURE MONITOR” of “BCM”.
Is DTC “C1716”, “C1717”, “C1718”, or “C1719” detected?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
CHECK LOW TIRE PRESSURE WARNING LAMP
Check that after the ignition switch is turned ON, the low tire pressure warning lamp illuminates for approxi-
mately 1 second and then turns OFF.
Is the inspection result normal?
YES
>> After erase DTC, INSPECTION END.
NO
>> Leave the ignition switch ON and proceed to
Diagnosis Procedure
INFOID:0000000012201854
1.
PERFORM TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration for all wheels. Refer to
Is tire pressure sensor ID registration completed?
YES
>> GO TO 2.
NO
>> Replace tire pressure sensor. Refer to
WT-41, "Removal and Installation"
2.
CHECK TIRE PRESSURE SIGNAL
With CONSULT
1. Check the tire pressure for all wheels and adjust to the specified value. Refer to
.
2. Stop the vehicle.
3. Select “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.
4. Within 15 minutes after vehicle stopped, read the values that are displayed for “AIR PRESS FL”, “AIR
PRESS FR”, “AIR PRESS RR”, and “AIR PRESS RL”.
Which tire pressures is displayed as 438.60 kPa (4.47 kg/cm
2
, 63.60 psi)?
DTC
Display Item
Malfunction detected condition
Possible causes
C1716
[PRESSDATA ERR] FL
Malfunction in the tire pressure data from the
front LH wheel tire pressure sensor.
• Excessive tire pressure
• Tire pressure sensor ID reg-
istration incomplete
• Tire pressure sensor
C1717
[PRESSDATA ERR] FR
Malfunction in the tire pressure data from the
front RH wheel tire pressure sensor.
C1718
[PRESSDATA ERR] RR
Malfunction in the tire pressure data from the
rear RH wheel tire pressure sensor.
C1719
[PRESSDATA ERR] RL
Malfunction in the tire pressure data from the
rear LH wheel tire pressure sensor.
Revision: November 2015
2016 JUKE
C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR
WT-27
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
YES
>> Replace tire pressure sensor the tire pressure as 438.60 kPa (4.47 kg/cm
2
, 63.60 psi) displayed.
WT-41, "Removal and Installation"
.
NO
>> Perform “DTC CONFIRMATION PROCEDURE” (self-diagnosis) again. Refer to
.
Revision: November 2015
2016 JUKE
WT-28
< DTC/CIRCUIT DIAGNOSIS >
C1729 VEHICLE SPEED SIGNAL
C1729 VEHICLE SPEED SIGNAL
DTC Logic
INFOID:0000000012201855
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC CONFIRMATION PROCEDURE
With CONSULT
1. Drive the vehicle.
2. Stop the vehicle.
3. Perform self-diagnosis in “AIR PRESSURE MONITOR” of “BCM”.
Is DTC “C1729” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012201856
1.
PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ABS”.
Is any DTCs detected?
YES
>> Check the DTCs.
NO
>> GO TO 2.
2.
CHECK BCM INPUT/OUTPUT SIGNAL
Check BCM input/output signal values. Refer to
.
Is the inspection result normal?
YES
>> Check pin terminal and connection of each harness connector for malfunctioning conditions.
NO
BCS-94, "Removal and Installation"
DTC
Display Item
Malfunction detected condition
Possible causes
C1729
VHCL SPEED SIG ERR
Vehicle speed signal not detected.
• CAN communication
• BCM
• ABS actuator and electric unit (control unit) malfunction
Revision: November 2015
2016 JUKE
POWER SUPPLY AND GROUND CIRCUIT
WT-29
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000012201857
1.
CHECK BCM POWER SUPPLY AND GROUND CIRCUIT
Check BCM power supply and ground. Refer to
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
Revision: November 2015
2016 JUKE
WT-30
< SYMPTOM DIAGNOSIS >
TPMS
SYMPTOM DIAGNOSIS
TPMS
Symptom Table
INFOID:0000000012201858
LOW TIRE PRESSURE WARNING LAMP SYMPTOM CHART
Diagnosis items
Symptom
(Ignition switch
ON)
Low tire pressure warning lamp
Cause
Action
Low tire pres-
sure warning
lamp
The low tire pres-
sure warning lamp
illuminates for 1
second, then turns
OFF.
Wake-up operation for all
tire pressure sensors at
wheels is completed.
No system malfunctions
The low tire pres-
sure warning lamp
repeats blinking
ON for 2 seconds
and OFF for 0.2
seconds.
Wake-up operation for all
tire pressure sensors at
wheels is not completed.
Perform the ID registration
for all tire pressure sensors
at wheels. Refer to
Low tire pres-
sure warning
lamp
The low tire pres-
sure warning lamp
blinks once.
The front left tire pres-
sure sensor is not acti-
vated.
Perform the ID registration
for the tire pressure sensor
at front left wheel. Refer to
.
The low tire pres-
sure warning lamp
repeats blinking
twice.
The front right tire pres-
sure sensor is not acti-
vated.
Perform the ID registration
for the tire pressure sensor
at front right wheel. Refer to
.
The low tire pres-
sure warning lamp
repeats blinking for
3 times.
The rear right tire pres-
sure sensor is not acti-
vated.
Perform the ID registration
for the tire pressure sensor
at rear right wheel. Refer to
.
The low tire pres-
sure warning lamp
repeats blinking for
4 times.
The rear left tire pressure
sensor is not activated.
Perform the ID registration
for the tire pressure sensor
at rear left wheel. Refer to
.
SEIA0592E
SEIA0593E
JPEIC0090GB
SEIA0595E
SEIA0596E
SEIA0597E
Revision: November 2015
2016 JUKE
TPMS
WT-31
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
NOTE:
If tire pressure sensor wake-up operation is not completed for two or more tire pressure sensors, the applica-
ble low tire pressure warning lamp blinking patterns are displayed continuously.
(Example: Blinks once/OFF/blinks 3 times = Wake-up operation is not completed at the front left wheel and
rear right wheel tire pressure sensors.)
Low tire pres-
sure warning
lamp
The low tire pres-
sure warning lamp
turns ON and stays
illuminated.
Low tire pressure
Check the tire pressure for
all wheels and adjust to the
specified value. Refer to
The low tire pres-
sure warning lamp
repeats blinking at
0.5-second inter-
vals for 1 minute,
and then stays illu-
minated.
The combination meter
fuse is open or removed
(or pulled out).
Check and install the com-
bination meter fuse. If nec-
essary, replace the fuse.
The BCM harness con-
nector is removed.
Check the connection con-
ditions of the BCM harness
connector, and repair if nec-
essary.
Tire Pressure Monitoring
System (TPMS) mal-
function.
• Perform CONSULT self-
diagnosis. Refer to
10, "AIR PRESSURE
MONITOR : CONSULT
Function (BCM - AIR
PRESSURE MONI-
TOR)"
• If necessary, perform tire
pressure sensor ID regis-
tration. Refer to
Diagnosis items
Symptom
(Ignition switch
ON)
Low tire pressure warning lamp
Cause
Action
SEIA0598E
SEIA0788E
Revision: November 2015
2016 JUKE
WT-32
< SYMPTOM DIAGNOSIS >
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON
Description
INFOID:0000000012201859
The low tire pressure warning lamp does not illuminate when the ignition switch is turned ON.
NOTE:
The low tire pressure warning lamp illuminates for approximately 1 second and then turns OFF when the igni-
tion switch is turned ON. This is to check that no abnormal condition is present in the tire pressure monitoring
system.
The lamp bulb may be burnt out or the tire pressure monitoring system may be malfunctioning if the low tire
pressure warning lamp does not illuminate when the ignition switch is turned ON.
Diagnosis Procedure
INFOID:0000000012201860
1.
CHECK LOW TIRE PRESSURE WARNING LAMP SIGNAL
With CONSULT
1. Turn the ignition switch ON.
CAUTION:
Never start the engine.
2. Select “ACTIVE TEST” in “AIR PRESSURE MONITOR” of “BCM”.
3. Touch “WARNING LAMP” to turn ON the low tire pressure warning lamp.
When “ACTIVE TEST” is performed, does the low tire pressure warning lamp in the combination meter turn
ON?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK LOW TIRE PRESSURE WARNING LAMP OPERATION
Check that the low tire pressure warning lamp is turned OFF after turns ON for approximately 1 second, when
the ignition switch is turned ON.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
BCS-94, "Removal and Installation"
3.
CHECK COMBINATION METER POWER SUPPLY CIRCUIT
Perform the trouble diagnosis for combination meter power supply circuit. Refer to
Is the inspection result normal?
YES-1 >> INSPECTION END
NO
>> Repair or replace error-detected parts.
Revision: November 2015
2016 JUKE
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF
WT-33
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF
Description
INFOID:0000000012201861
The low tire pressure warning lamp does not turn OFF after several seconds is passed after engine starts.
Diagnosis Procedure
INFOID:0000000012201862
1.
CHECK TIRE PRESSURE
1. Turn the ignition switch ON.
CAUTION:
Never start the engine.
2. Check the tire pressure for all wheels and adjust to the specified value. Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Inspect or repair the tires or wheels.
2.
CHECK LOW TIRE PRESSURE WARNING LAMP
Check low tire pressure warning lamp display.
Does not low tire pressure warning lamp turn OFF?
YES
>> GO TO 3.
NO
>> INSPECTION END
3.
CHECK BCM
With CONSULT
Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
NO
>> GO TO 4.
4.
CHECK BCM POWER SUPPLY AND GROUND CIRCUIT
Perform the trouble diagnosis for power supply and ground circuit. Refer to
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст