Nissan Juke (2016 year). Service Repair Manual — part 361
EXL-110
< REMOVAL AND INSTALLATION >
[XENON TYPE]
REAR COMBINATION LAMP
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
TAIL LAMP (LED)
CAUTION:
Replacement of a single part is not possible due to the adoption of LED. For replacement, replace rear
combination lamp as a set. Refer to
EXL-109, "Removal and Installation"
.
STOP/TAIL LAMP BULB (REAR SIDE MARKER LAMP)
1. Remove rear combination lamp assembly. Refer to
EXL-109, "Removal and Installation"
.
2. Rotate stop/tail lamp bulb socket counterclockwise, and then remove stop/tail lamp bulb socket.
3. Remove stop/tail lamp bulb from stop/tail lamp bulb socket.
REAR TURN SIGNAL LAMP BULB
1. Remove rear combination lamp assembly. Refer to
EXL-109, "Removal and Installation"
.
2. Rotate rear turn signal lamp bulb socket counterclockwise, and then remove rear turn signal lamp bulb
socket.
3. Remove rear turn signal lamp bulb from rear turn signal lamp bulb socket.
BACK-UP LAMP BULB
1. Remove rear combination lamp assembly. Refer to
EXL-109, "Removal and Installation"
.
2. Rotate back-up lamp bulb socket counterclockwise, and then remove back-up lamp bulb socket.
3. Remove back-up lamp bulb from back-up lamp bulb socket.
Revision: November 2015
2016 JUKE
HIGH-MOUNTED STOP LAMP
EXL-111
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HIGH-MOUNTED STOP LAMP
Exploded View
INFOID:0000000012201702
EXCEPT FOR NISMO AND NISMO RS
NISMO AND NISMO RS
Removal and Installation
INFOID:0000000012201703
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
EXL-7, "Precautions for Removing Battery Terminal"
.
REMOVAL
Except for NISMO and NISMO RS
1. Remove blind seal from back door inside.
CAUTION:
1.
High-mounted stop lamp
2.
Seal packing
: N·m (kg-m, in-lb)
JMLIA1220GB
1.
Rear spoiler
2.
High-mounted stop lamp
3.
High-mounted stop lamp cover
JMLIA3757ZZ
Revision: November 2015
2016 JUKE
EXL-112
< REMOVAL AND INSTALLATION >
[XENON TYPE]
HIGH-MOUNTED STOP LAMP
Never damage the blind seal, so that it can be reused.
2. Remove high-mounted stop lamp mounting nuts and connector.
3. Pull high-mounted stop lamp toward vehicle upside, and then remove high-mounted stop lamp.
NISMO and NISMO RS
1. Remove rear spoiler. Refer to
EXT-49, "Removal and Installation"
.
2. Remove high-mounted stop lamp cover mounting bolts, and then remove high-mounted stop lamp cover.
3. Remove high-mounted stop lamp harness connector from rear spoiler.
4. Pull out high-mounted stop lamp, and then remove high-mounted stop lamp.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
Seal packing cannot be reused.
Revision: November 2015
2016 JUKE
LICENSE PLATE LAMP
EXL-113
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LICENSE PLATE LAMP
Exploded View
INFOID:0000000012201704
Removal and Installation
INFOID:0000000012201705
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
EXL-7, "Precautions for Removing Battery Terminal"
.
REMOVAL
1. While pressing the license plate lamp to direction right side, pull
it to direction outside and then remove it.
2. Disconnect license plate lamp connector.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000012201706
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
EXL-7, "Precautions for Removing Battery Terminal"
.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
LICENSE PLATE LAMP BULB
1. Remove license plate lamp. Refer to
EXL-113, "Removal and Installation"
2. Rotate the bulb socket counterclockwise and unlock it.
1.
License plate lamp housing assembly
2.
Bulb
3.
License plate lamp bulb socket
: Pawl
JMLIA1219ZZ
JPLIA0364ZZ
Revision: November 2015
2016 JUKE
EXL-114
< REMOVAL AND INSTALLATION >
[XENON TYPE]
LICENSE PLATE LAMP
3. Remove the bulb from the socket.
Revision: November 2015
2016 JUKE
REAR FOG LAMP
EXL-115
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REAR FOG LAMP
Exploded View
INFOID:0000000012201707
REMOVAL
Removal and Installation
INFOID:0000000012201708
REMOVAL
1. Remove rear bumper fascia lower. Refer to
EXT-23, "Removal and Installation"
2. Remove rear fog lamp housing mounting nuts.
3. Remove rear fog lamp housing from the rear bumper fascia lower.
4. Remove rear fog lamp housing bracket from rear bumper fascia lower.
INSTALLATION
Installation is the reverse order of removal.
1.
Rear fog lamp housing
2.
Rear bumper fascia lower
3.
Rear fog lamp housing bracket
N·m (kg-m, in-lb)
: Vehicle front
JMLIA3677GB
Revision: November 2015
2016 JUKE
EXL-116
< REMOVAL AND INSTALLATION >
[XENON TYPE]
REAR REFLEX REFLECTOR
REAR REFLEX REFLECTOR
Exploded View
INFOID:0000000012201709
EXCEPT FOR NISMO AND NISMO RS
NISMO AND NISMO RS
Removal and Installation
INFOID:0000000012201710
REMOVAL
Except for NISMO and NISMO RS
1. Remove rear bumper fascia lower. Refer to
EXT-23, "Removal and Installation"
1.
Rear bumper fascia lower
2.
Rear reflex reflector LH
3.
Rear reflex reflector RH
: Pawl
: N·m (kg-m, in-lb)
JMLIA5406GB
1.
Rear bumper fascia lower
2.
Rear reflex reflector RH
3.
Rear reflex reflector LH
: Metal clip
: Vehicle front
JMLIA3679ZZ
Revision: November 2015
2016 JUKE
REAR REFLEX REFLECTOR
EXL-117
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
2. Remove rear reflex reflector fixing screw.
3. Disengage rear reflex reflector fixing pawls, and then remove rear reflex reflector.
NISMO and NISMO RS
1. Remove rear bumper fascia lower. Refer to
EXT-23, "Removal and Installation"
2. Disengage rear reflex reflector fixing metal clip, and then
remove rear reflex reflector according to numerical order 1
→
3
indicated by arrows as shown in the figure.
INSTALLATION
Install in the reverse order of removal.
JMLIA3680ZZ
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст