Nissan Juke (2016 year). Service Repair Manual — part 451
INT-14
< REMOVAL AND INSTALLATION >
FRONT DOOR FINISHER
1. Remove cap in the pull handle.
2. Remove pull handle fixing screw.
3. Lift up the pull handle while rotating it in direction indicated
by the arrow as shown in the figure. Disengage pawls and
remove the pull handle.
3. Remove power window switch finisher and power window switch in one body.
1. Disengage power window switch finisher fixing pawl with a
remover tool (A).
CAUTION:
Apply protective tape (B) on the parts to protect it from
damage.
2. Pull up power window switch finisher and power window
switch with one body and disconnect harness connector.
4. Remove door mirror corner cover. Refer to
MIR-17, "DOOR MIRROR ASSEMBLY : Removal and Installa-
5. Disengage front door finisher fixing clips and metal clips with a
remover tool (A), and then remove front door finisher.
CAUTION:
Insert a remover tool between body side panel and clip and
disengage pawl.
NOTE:
Remove power window switch. Refer to
PWC-54, "Removal and Installation"
.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
JMJIA4518ZZ
: Pawl
JMJIA4519ZZ
: Pawl
JMJIA4520ZZ
: Clip
: Metal clip
JMJIA4521ZZ
Revision: November 2015
2016 JUKE
FRONT DOOR FINISHER
INT-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
When installing front door finisher, check that clips, and metal clips are securely in body panel holes,
and press them in.
Revision: November 2015
2016 JUKE
INT-16
< REMOVAL AND INSTALLATION >
REAR DOOR FINISHER
REAR DOOR FINISHER
Exploded View
INFOID:0000000012199170
Removal and Installation
INFOID:0000000012199171
REMOVAL
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the door panel.
1. Fully open door window.
2. Remove rear corner cover inner.
1.
Rear door panel
2.
Grommet
3.
Rear door corner cover inner
4.
Cap
5.
Power window switch finisher
6.
Rear door finisher
: Clip
: Pawl
: Metal clip
JMJIA4522ZZ
Revision: November 2015
2016 JUKE
REAR DOOR FINISHER
INT-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Disengage rear corner cover inner fixing pawl with a remover
tool (A).
3. Remove power window switch finisher and power window switch in one body.
Pull up power window switch finisher and power window switch
with one body and disconnect harness connector.
4. Remove rear door finisher fixing screw.
5. Disengage rear door finisher fixing clips and metal clips with a
remover tool (A), and then remove rear door finisher.
CAUTION:
Insert a remover tool between body side panel and clip and
disengage pawl.
NOTE:
Remove power window switch. Refer to
PWC-54, "Removal and Installation"
.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing rear door finisher, check that clips, and metal clips are securely in body panel holes,
and press them in.
: Clip
JMJIA4523ZZ
: Pawl
JMJIA4525ZZ
: Clip
: Metal clip
JMJIA4526ZZ
Revision: November 2015
2016 JUKE
INT-18
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
BODY SIDE TRIM
Exploded View
INFOID:0000000012199172
FRONT PILLAR GARNISH
FRONT PILLAR GARNISH : Removal and Installation
INFOID:0000000012199173
REMOVAL
CAUTION:
1.
Rear body side welt
2.
Center pillar upper garnish
3.
Front body side welt
4.
Front pillar garnish
5.
Metal clip
6.
Dash side finisher RH
7.
Harness clip
8.
Front kicking plate inner
9.
Center pillar lower garnish
10. Rear kicking plate inner
: Clip
: Pawl
: Metal clip
: Vehicle front
: Always replace after every disassembly.
JMJIA4527ZZ
Revision: November 2015
2016 JUKE
BODY SIDE TRIM
INT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
1. Release front pillar garnish portion of front body side welt.
2. Remove front pillar garnish.
1. Disengage front pillar garnish fixing anchor clips with a
remover tool (A).
2. Cut anchor clip portion, and then remove front pillar garnish.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Replace anchor clip with a new part after removal. Never reuse anchor clip.
• Be sure to install anchor clip to front pillar garnish before installing front pillar garnish to the vehicle
body.
• When installing anchor clip to front pillar garnish, be sure to
align the notch and then insert anchor clip.
• After installing anchor clip to front pillar garnish, check that anchor clip is engaged securely to front
pillar garnish. If anchor clip is not engaged securely, front pillar garnish may be lifted and disen-
gaged from the vehicle body.
• When installing front pillar garnish, check that anchor clips are securely in body panel holes, and
press them in.
KICKING PLATE INNER
KICKING PLATE INNER : Removal and Installation
INFOID:0000000012199174
REMOVAL
CAUTION:
• When removing, always use a remover tool that is made of plastic to prevent damage to the parts.
• Never damage the body.
: Anchor Clip
JMJIA7046ZZ
JMJIA5130ZZ
JMJIA7045ZZ
Revision: November 2015
2016 JUKE
INT-20
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
FRONT KICKING PLATE INNER
1. Disengage fixing pawls on front lower end of front kicking plate
inner using a remover tool (A).
CAUTION:
Apply protective tape (B) on the parts to protect it from
damage.
2. Lift up toward vehicle upper and disengage fixing pawls of front
kicking plate inner starting from the front.
CAUTION:
Never lift up excessively. Otherwise, rear end of front kick-
ing plate inner may be damaged.
3. Lift up lower rear end of front kicking plate inner while pulling it
toward vehicle inside, disengage fixing pawls of front kicking
plate inner, and then remove front kicking plate inner.
REAR KICKING PLATE INNER
1. Remove rear seat cushion. Refer to
SE-32, "SEAT CUSHION : Removal and Installation"
.
2. Disengage fixing pawls on front lower end of rear kicking plate
inner using a remover tool (A).
CAUTION:
Apply protective tape (B) on the parts to protect it from
damage.
: Pawl
: Vehicle front
JMJIA6562ZZ
: Pawl
JMJIA6563ZZ
: Pawl
JMJIA6564ZZ
: Pawl
JMJIA6565ZZ
Revision: November 2015
2016 JUKE
BODY SIDE TRIM
INT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
3. Lift up toward vehicle upper and disengage fixing pawls of rear
kicking plate inner starting from the front.
CAUTION:
Never lift up excessively. Otherwise, rear end of rear kicking
plate inner may be damaged.
4. Using a remover tool (A), lift up lower rear end of rear kicking
plate inner while disengaging a fixing pawl on lower rear end of
rear kicking plate inner, disengage remaining fixing pawls, and
then remove rear kicking plate inner.
CAUTION:
Apply protective tape (B) on the parts to protect it from
damage.
INSATALLATION
Install in the reverse order of removal.
DASH SIDE FINISHER
DASH SIDE FINISHER : Removal and Installation
INFOID:0000000012199175
REMOVAL
CAUTION:
Never damage the body.
1. Remove front kicking plate inner. Refer to
INT-19, "KICKING PLATE INNER : Removal and Installation"
2. Pull back dash side finisher, and then disengage the pawls.
3. Disconnect dash side finisher, vehicle front side, from stud bolt and remove dash side finisher.
INSTALLATION
Install in the reverse order of removal.
BODY SIDE WELT
BODY SIDE WELT : Removal and Installation
INFOID:0000000012199176
REMOVAL
CAUTION:
• Never excessively pull body side welt.
• Never damage the body.
FRONT BODY SIDE WELT
: Pawl
JMJIA6566ZZ
: Pawl
JMJIA6567ZZ
: Pawl
JMJIA4529ZZ
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст