Nissan Juke (2016 year). Service Repair Manual — part 452
INT-22
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
1. Remove front kicking plate inner. Refer to
INT-19, "KICKING PLATE INNER : Removal and Installation"
2. Remove front body side welt.
REAR BODY SIDE WELT
1. Remove rear kicking plate inner. Refer to
INT-19, "KICKING PLATE INNER : Removal and Installation"
.
2. Remove rear body side welt.
INSTALLATION
Install in the reverse order of removal.
CENTER PILLAR LOWER GARNISH
CENTER PILLAR LOWER GARNISH : Removal and Installation
INFOID:0000000012199177
REMOVAL
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
1. Fully open front door and rear door.
2. Slide front seat to the fully forward position. Tilt seatback forward.
3. Remove Front body side welt and rear body side welt. Refer to
INT-21, "BODY SIDE WELT : Removal
4. Disengage center pillar lower garnish fixing clips and pawls with
a remover tool (A), and then remove center pillar lower garnish.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing center pillar lower garnish, check that clips are securely in body panel holes, and
press them in.
CENTER PILLAR UPPER GARNISH
CENTER PILLAR UPPER GARNISH : Removal and Installation
INFOID:0000000012199178
REMOVAL
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
1. Remove center pillar lower garnish. Refer to
INT-22, "CENTER PILLAR LOWER GARNISH : Removal
2. Remove front seat belt shoulder anchor. Refer to
SB-6, "SEAT BELT RETRACTOR : Removal and Instal-
.
: Clip
: Pawl
JMJIA4390ZZ
Revision: November 2015
2016 JUKE
BODY SIDE TRIM
INT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
3. Disengage center pillar upper garnish lower side fixing pawl
using a remover tool.
4. Disengage center pillar upper garnish upper side fixing clip using a remover tool (A).
NOTE:
Removal operation can be performed easily when pressing pawl by inserting a removal tool from direction
(A) as shown in the figure.
CAUTION:
Be careful not to apply excessive force when removing center pillar upper garnish. Otherwise,
pawl may be damaged and fragments may drop in panel holes on body.
INATALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Replace center pillar upper garnish with a new part after removal. Never reuse center pillar upper
garnish.
• When installing center pillar upper garnish, check that pawls are securely in body panel holes, and
press them in.
: Pawl
JMJIA4391ZZ
PIIB7674J
Revision: November 2015
2016 JUKE
INT-24
< REMOVAL AND INSTALLATION >
FLOOR TRIM
FLOOR TRIM
Exploded View
INFOID:0000000012199179
Removal and Installation
INFOID:0000000012199180
REMOVAL
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
1. Remove front seat assembly (LH and RH). Refer to
SE-21, "Removal and Installation"
2. Remove rear seat cushion. Refer to
SE-32, "SEAT CUSHION : Removal and Installation"
.
3. Remove center console assembly. Refer to
IP-24, "Removal and Installation"
4. Remove instrument stay.
1.
Floor carpet
2.
Carpet hook
3.
Trim clip
4.
Column hole cover
5.
Harness clip
6.
Front floor spacer RH
7.
Front floor spacer LH
8.
Rear floor spacer LH
9.
Rear floor spacer RH
: Clip
: Pawl
JMJIA4530ZZ
Revision: November 2015
2016 JUKE
FLOOR TRIM
INT-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Remove instrument stay mounting nuts (A), and then remove
instrument stay.
5. Disconnect drain hose. Refer to
HA-43, "A/C UNIT ASSEMBLY : Removal and Installation"
.
6. Remove foot ducts (LH and RH). Refer to
VTL-13, "FOOT DUCT : Removal and Installation"
(Models with
foot ducts).
7. Remove shift selector assembly
• 6MT models: Refer to
TM-25, "Removal and Installation"
• CVT models: Refer to
TM-316, "Removal and Installation"
8. Remove diagnosis sensor unit. Refer to
SR-29, "Removal and Installation"
.
9. Remove parking brake lever. Refer to
PB-7, "Removal and Installation"
10. Remove center pillar lower garnish (LH and RH). Refer to
INT-22, "CENTER PILLAR LOWER GARNISH :
.
11. Remove column hole cover.
Disengage trim clip (A), and then remove column hole cover.
12. Remove dash side finisher (LH and RH). Refer to
INT-21, "DASH SIDE FINISHER : Removal and Installa-
13. Disengage pawl using a remover tool (A) and open the harness
clip.
14. Remove floor carpet.
NOTE:
: Vehicle front
JMJIA4531ZZ
JMJIA4532ZZ
: Pawl
JMJIA4396ZZ
Revision: November 2015
2016 JUKE
INT-26
< REMOVAL AND INSTALLATION >
FLOOR TRIM
Disengage pawls using a remover tool and remove carpet hook.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
Replace diagnosis sensor unit fixing bolts with a new part after removal. Never reuse diagnosis sen-
sor unit fixing bolts.
: Pawl
JMJIA3620ZZ
Revision: November 2015
2016 JUKE
HEADLINING
INT-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
HEADLINING
NORMAL ROOF
NORMAL ROOF : Exploded View
INFOID:0000000012199181
NORMAL ROOF
NORMAL ROOF : Removal and Installation
INFOID:0000000012199182
REMOVAL
JMJIA4533ZZ
1.
Headlining assembly
2.
Assist grip clip
3.
Rear assist grip RH
4.
Front assist grip RH
5.
Sun visor assembly RH
6.
Sun visor cover RH
7.
Sun visor cover LH
8.
Sun visor assembly LH
9.
Rear assist grip LH
10. Headlining clip
11. Sun visor holder RH
12. Map lamp
13. Sun visor holder LH
14. Metal clip
: Clip
: Pawl
Revision: November 2015
2016 JUKE
INT-28
< REMOVAL AND INSTALLATION >
HEADLINING
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
1. Remove front pillar garnish (LH and RH). Refer to
INT-18, "FRONT PILLAR GARNISH : Removal and
.
2. Disconnect harness connector (A) from headlining and harness
clips
3. Remove center pillar upper garnish (LH and RH). Refer to
INT-22, "CENTER PILLAR UPPER GARNISH :
.
4. Remove back door weather-strip. Refer to
DLK-152, "BACK DOOR WEATHER-STRIP : Removal and
(with Intelligent Key System).
5. Remove luggage side upper finisher (LH and RH). Refer to
INT-36, "LUGGAGE SIDE UPPER FINISHER
.
6. Remove all assist grips.
1. Disengage pawl of assist grip clip (1) using a remover tool
(A). Slide assist grip clip forward and remove it.
2. Slide assist grip (2) forward and remove it.
3. Remove metal clips.
7. Remove sun visor assembly (LH and RH).
1. Disengage sun visor cover fixing pawls with a remover tool
(A), and then remove sun visor cover.
2. Remove sun visor assembly fixing screws, and then slide toward vehicle rear to remove sun visor
assembly.
8. Remove map lamp assembly. Refer to
INL-46, "Removal and Installation"
9. Remove front seat assembly (passenger). Refer to
SE-21, "Removal and Installation"
.
10. Remove sun visor holder (LH and RH).
: Clip
JMJIA4534ZZ
: Pawl
JMJIA4398ZZ
: Pawl
JMJIA4399ZZ
Revision: November 2015
2016 JUKE
HEADLINING
INT-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Rotate 90
°
. Remove toward vehicle lower.
11. Remove headlining clips.
12. Remove headlining assembly through the back door.
CAUTION:
• Two workers are required for removal in order to prevent
damage.
• Apply protective tape to the portion where contact may
occur during work.
• Never bend headlining when removing.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• When installing headlining, start by installing both sun visor holders and headlining clips in order to
keep the headlining in position.
• Never bend headlining when installing.
• Be careful that the surface is not wrinkled when installing.
SUNROOF
JMJIA4401ZZ
JMJIA4402ZZ
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст