Nissan Juke (2016 year). Service Repair Manual — part 546
RF-36
< REMOVAL AND INSTALLATION >
GLASS LID
After adjustment the sunroof unit assembly, perform additional service. Refer to
VICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement"
Revision: November 2015
2016 JUKE
SUNROOF MOTOR ASSEMBLY
RF-37
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
SUNROOF MOTOR ASSEMBLY
Exploded View
INFOID:0000000012196983
Removal and Installation
INFOID:0000000012196984
REMOVAL
CAUTION:
• Before removing sunroof motor, check that glass lid is fully closed.
• After removing sunroof motor, never attempt to rotate sunroof motor assembly as a single unit.
1. Fully close glass lid.
1.
TORX bolt
2.
Glass lid
3.
Sunroof bracket
4.
Drain hose (front)
5.
Drain connector (front)
6.
Sunroof welt
7.
Sunroof motor assembly
8.
Drain hose (rear)
9.
Drain connector (rear)
10. Sunroof unit assembly
11. Seal guide rubber
12. Seal sunroof
: Indicates that the part is connected at points with same symbol in actual vehicle.
JSKIA2884ZZ
Revision: November 2015
2016 JUKE
RF-38
< REMOVAL AND INSTALLATION >
SUNROOF MOTOR ASSEMBLY
2. Remove headlining. Refer to
INT-30, "SUNROOF : Removal and Installation"
3. Remove sunroof motor.
1. Disconnect harness connector (A) from sunroof motor.
2. Remove sunroof motor assembly fixing screws (B), and
then remove sunroof motor assembly.
INSTALLATION
CAUTION:
Before installing the sunroof motor assembly, be sure to the place the link and wire assembly in the
symmetrical and fully closed position.
1. Move the sunroof motor assembly laterally by little so that the gear is completely engaged into the wire on
the sunroof unit assembly and mounting surface becomes parallel. Then secure the sunroof motor
assembly with screws.
2. Install headlining.
NOTE:
After installation sunroof motor, perform additional service. Refer to
RF-17, "ADDITIONAL SERVICE WHEN
REPLACING CONTROL UNIT : Description"
.
JMKIA5811ZZ
Revision: November 2015
2016 JUKE
SUNROOF UNIT ASSEMBLY
RF-39
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
SUNROOF UNIT ASSEMBLY
Exploded View
INFOID:0000000012196985
REMOVAL
DISASSEMBLY
1.
TORX bolt
2.
Glass lid
3.
Sunroof bracket
4.
Drain hose (front)
5.
Drain connector (front)
6.
Sunroof welt
7.
Sunroof motor assembly
8.
Drain hose (rear)
9.
Drain connector (rear)
10. Sunroof unit assembly
11. Seal guide rubber
12. Seal sunroof
: Indicates that the part is connected at points with same symbol in actual vehicle.
JSKIA2884ZZ
Revision: November 2015
2016 JUKE
RF-40
< REMOVAL AND INSTALLATION >
SUNROOF UNIT ASSEMBLY
Removal and Installation
INFOID:0000000012196986
REMOVAL
CAUTION:
• Always work with a helper.
• Fully close the glass lid assembly, before removal, then never operate sunroof motor assembly after
removal.
• After removing sunroof motor, never attempt to rotate sunroof motor assembly as a single unit.
• When remove/install sunroof unit, use cloths to protect the seats and trim from damage.
• After installing the sunroof unit and glass lid, perform the leak test and check that there is no mal-
function.
1. Remove glass lid. Refer to
RF-34, "Removal and Installation"
2. Remove headlining. Refer to
INT-30, "SUNROOF : Removal and Installation"
3. Disconnect drain hoses.
1.
Rear drain assembly
2.
Wind deflector
3.
Sunshade stopper
4.
Sunroof frame assembly
5.
Seating deflector
6.
Sunshade
JSKIA2885ZZ
Revision: November 2015
2016 JUKE
SUNROOF UNIT ASSEMBLY
RF-41
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
4. Remove sunroof brackets mounting bolts, and then remove sunroof brackets.
5. Remove bolts from the front end and side rail, and then remove sunroof unit assembly from roof panel.
6. Remove sunroof unit assembly through the passenger compartment while being careful not to damage
the seats and trim.
INSTALLATION
1. Temporarily tighten the mounting bolts to the both side of sunroof unit assembly.
2. Temporarily tighten the mounting bolts to the front end of sunroof unit assembly.
3. Temporarily tighten the mounting bolts to the sunroof brackets (LH and RH).
4. Tighten the installation points diagonally excluding the installation points of the sunroof brackets around
the roof opening.
5. Tighten the sunroof bracket bolts of the vehicle side, and then tighten the bolt of the sunroof unit assembly
side.
6. Tighten the mounting bolts to the front end and both side of sunroof unit assembly.
7. Connect drain hoses.
8. Install headlining. Refer to
INT-30, "SUNROOF : Removal and Installation"
9. Install glass lid. Refer to
RF-34, "Removal and Installation"
10. Install side trims.
NOTE:
• After installation, perform fitting adjustment. Refer to
.
• After installation sunroof unit assembly, perform additional service. Refer to
WHEN REPLACING CONTROL UNIT : Description"
.
Disassembly and Assembly
INFOID:0000000012196987
DISASSEMBLY
1. Remove sunshade stopper mounting from the rear end of sunroof frame.
2. Remove sunshade from the rear end of sunroof frame.
3. Remove rear drain assembly from sunroof guide assembly.
ASSEMBLY
Assemble in the reverse order of disassembly.
Revision: November 2015
2016 JUKE
RF-42
< REMOVAL AND INSTALLATION >
SUNSHADE
SUNSHADE
Exploded View
INFOID:0000000012196988
Removal and Installation
INFOID:0000000012196989
REMOVAL
1. Remove headlining. Refer to
INT-30, "SUNROOF : Removal and Installation"
1.
Rear drain assembly
2.
Wind deflector
3.
Sunshade stopper
4.
Sunroof frame assembly
5.
Seating deflector
6.
Sunshade
JSKIA2885ZZ
Revision: November 2015
2016 JUKE
SUNSHADE
RF-43
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
2. Remove the sunshade stopper (1) from the rear end of sunroof
frame.
3. Remove the sunshade from the rear end of sunroof frame.
INSTALLATION
Install in the reverse order of removal.
JMKIA2045ZZ
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст