Nissan Juke (2016 year). Service Repair Manual — part 544
RF-20
< DTC/CIRCUIT DIAGNOSIS >
SUNROOF MOTOR ASSEMBLY
SUNROOF MOTOR ASSEMBLY
Component Function Check
INFOID:0000000012196966
1.
CHECK SUNROOF MOTOR FUNCTION
Check tilt up/down & slide open/close operations with sunroof switch.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check sunroof switch. Refer to
.
2.
CHECK SUNROOF MOTOR ASSEMBLY INPUT SIGNAL
1. Start engine.
2. Drive the vehicle at more than 40 km/h (25 MPH).
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
This procedure may be conducted with the drive wheels lifted in the shop or by driving the vehicle.
If a road test is expected to be easier, it is unnecessary to lift the vehicle.
3. Check tilt up/down & slide open/close operations with sunroof switch.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012196967
SUNROOF MOTOR ASSEMBLY
1.
CHECK SUNROOF MOTOR ASSEMBLY INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect combination meter harness connector and sunroof motor assembly harness connector.
3. Check continuity between combination meter harness connector and sunroof motor assembly harness
connector.
4. Check continuity between sunroof motor assembly harness connector and ground.
Is the inspection result normal?
YES
>> Check combination meter. Refer to
MWI-53, "COMBINATION METER : Diagnosis Procedure"
NO
>> Repair or replace harness or connector.
Combination meter
Sunroof motor assembly
Continuity
Connector
Terminal
Connector
Terminal
M34
4
R11
8
Exists
Sunroof motor assembly
Ground
Continuity
Connector
Terminal
R11
8
Not existed
Revision: November 2015
2016 JUKE
SUNROOF SWITCH
RF-21
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
SUNROOF SWITCH
Component Function Check
INFOID:0000000012196968
1.
CHECK SUNROOF MOTOR FUNCTION
Check tilt up/down & slide open/close operations with sunroof switch.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012196969
1.
PERFORM INITIALIZATION PROCEDURE
1. Initialization procedure is executed and operation is confirmed. Refer to
WHEN REPLACING CONTROL UNIT : Special Repair Requirement"
.
2. Check tilt up/down & slide open/close operations with sunroof switch.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK SUNROOF SWITCH GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect sunroof switch harness connector.
3. Check continuity between sunroof switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connector.
3.
CHECK SUNROOF SWITCH INPUT SIGNAL
1. Turn ignition switch ON.
2. Check voltage between sunroof switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK SUNROOF SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect sunroof motor assembly harness connector.
3. Check continuity between sunroof motor assembly harness connector and sunroof switch harness con-
nector.
Sunroof switch
Ground
Continuity
Connector
Terminal
R5
2
Existed
(+)
(
−
)
Voltage (V)
(Approx.)
sunroof switch
Connector
Terminal
R5
1
Ground
Battery Voltage
3
Revision: November 2015
2016 JUKE
RF-22
< DTC/CIRCUIT DIAGNOSIS >
SUNROOF SWITCH
4. Check continuity between sunroof motor assembly harness connector and ground.
Is the inspection result normal?
YES
>> Replace sunroof motor assembly. Refer to
RF-37, "Removal and Installation"
NO
>> Repair or replace harness or connector.
5.
CHECK SUNROOF SWITCH
Check sunroof switch.
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Replace sunroof switch (built in map lamp assembly). Refer to
RF-45, "Removal and Installation"
.
Component Inspection
INFOID:0000000012196970
SUNROOF SWITCH
1.
CHECK SUNROOF SWITCH
1. Turn ignition switch OFF.
2. Disconnect sunroof switch harness connector.
3. Check continuity sunroof switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace sunroof switch. Refer to
RF-45, "Removal and Installation"
Sunroof motor assembly
Sunroof switch
Continuity
Connector
Terminal
Connector
Terminal
R11
5
R5
1
Existed
10
3
Sunroof motor assembly
Ground
Continuity
Connector
Terminal
R11
5
Not existed
10
Terminals
Condition
Continuity
1
2
Sunroof switch is operated
TILT DOWN or SLIDE OPEN
Existed
Other than above
Not existed
3
Sunroof switch is operated
TILT UP or SLIDE CLOSE
Existed
Other than above
Not existed
Revision: November 2015
2016 JUKE
SUNROOF DOES NOT OPERATE PROPERLY
RF-23
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
SYMPTOM DIAGNOSIS
SUNROOF DOES NOT OPERATE PROPERLY
Description
INFOID:0000000012196971
Sunroof does not operate normally.
• Glass lid does not slide or tilt.
• Judder occurs during sliding operation of glass lid.
• Sliding or tilting operation of glass lid is slow.
Diagnosis Procedure
INFOID:0000000012196972
1.
CHECK GLASS LID
Check the following items.
• Cracks, damage, or deformation of weather-strip.
• Sticking of weather-strip.
• Loose or missing glass lid mounting blot.
• Misalignment of glass lid.
RF-34, "Removal and Installation"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK SUNROOF FRAME ASSEMBLY
Check the following items.
• Damage, deformation or trapped foreign material of slide rail.
• Insufficient application of grease to sliding section of slide rail.
RF-40, "Removal and Installation"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK SUNSHADE
Check sunshade for damage, deformation, of interference with other parts.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CHECK BCM POWER SUPPLY AND GROUND CIRCUIT
Check BCM power supply and ground circuit.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
CHECK SUNROOF MOTOR ASSEMBLY POWER SUPPLY AND GROUND CIRCUIT
Check sunroof motor assembly power supply and ground circuit.
RF-20, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace the malfunctioning parts.
6.
CHECK SUNROOF SWITCH
Check sunroof switch.
RF-21, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 7.
Revision: November 2015
2016 JUKE
RF-24
< SYMPTOM DIAGNOSIS >
SUNROOF DOES NOT OPERATE PROPERLY
NO
>> Repair or replace the malfunctioning parts.
7.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: November 2015
2016 JUKE
AUTO OPERATION DOES NOT OPERATE
RF-25
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
AUTO OPERATION DOES NOT OPERATE
Description
INFOID:0000000012196973
Auto operation does not operate
• Auto operation of glass lid does not operate.
• Glass lid stops halfway.
• Anti-pinch function operates.
Diagnosis Procedure
INFOID:0000000012196974
1.
CHECK GLASS LID
Check the following items.
• Cracks, damage, or deformation of weather-strip.
• Sticking of weather-strip.
• Loose or missing glass lid mounting blot.
• Misalignment of glass lid.
RF-34, "Removal and Installation"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK WIND DEFLECTOR
Check wind deflector for deformation and interference.
RF-44, "Removal and Installation"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK SUNROOF FRAME ASSEMBLY
Check the following items.
• Damage, deformation or trapped foreign material of slide rail.
• Insufficient application of grease to sliding section of slide rail.
RF-40, "Removal and Installation"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
PERFORM INITIALIZATION PROCEDURE
Perform initialization procedure.
RF-17, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description"
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace sunroof motor assembly. Refer to
RF-37, "Removal and Installation"
Revision: November 2015
2016 JUKE
RF-26
< SYMPTOM DIAGNOSIS >
SUNROOF DOES NOT OPERATE ANTI-PINCH FUNCTION
SUNROOF DOES NOT OPERATE ANTI-PINCH FUNCTION
Diagnosis Procedure
INFOID:0000000012196975
1.
PERFORM INITIALIZATION PROCEDURE
Perform initialization procedure.
RF-17, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description"
.
Is the inspection result normal?
YES
>> Inspection end.
NO
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
Revision: November 2015
2016 JUKE
RETAINED POWER OPERATION DOES NOT OPERATE PROPERLY
RF-27
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
RETAINED POWER OPERATION DOES NOT OPERATE PROPERLY
Diagnosis Procedure
INFOID:0000000012196976
1.
CHECK DOOR SWITCH
Check door switch.
DLK-77, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK SUNROOF MOTOR ASSEMBLY POWER SUPPLY AND GROUND
Check sunroof motor assembly power supply and ground circuit.
RF-20, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
• Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
• Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст