Nissan Juke (2016 year). Service Repair Manual — part 670
PADDLE SHIFTER
TM-553
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
5. Remove the paddle shifter connector (C) and (D) from paddle
shifter.
6. Remove the paddle shifter mounting bolts (E) and nuts (F).
7. Remove the paddle shifter from the steering column assembly.
INSTALLATION
Installation is in the reverse order of removal.
A
: Side of paddle shifter (shift-down switch)
B
: Side of paddle shifter (shift-up switch)
AWDIA0563ZZ
Revision: November 2015
2016 JUKE
TM-554
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
TCM
TCM
Exploded View
INFOID:0000000012201246
Removal and Installation
INFOID:0000000012201247
CAUTION:
• Never impact on TCM when removing or installing TCM.
• When replacing TCM, note the “CVTF DETERIORATION DATE” value displayed on CONSULT “CON-
FORM CVTF DETERIORTN” in MAINTENANCE BOOKLET, before start the operation.
• When replacing TCM and transaxle assembly simultaneously, replace transaxle assembly first and
then replace TCM.
• Before replacing TCM, perform “ADDITIONAL SERVICE WHEN REPLACING TCM”. Refer to
REMOVAL
1. Remove the battery. Refer to
PG-105, "Removal and Installation"
.
2. Remove air duct (inlet) and air cleaner case. Refer to
EM-192, "Removal and Installation"
.
3. Disconnect the TCM connector.
4. Remove the TCM.
5. Remove the bracket.
INSTALLATION
Installation is in the reverse order of removal.
Adjustment
INFOID:0000000012201248
ADJUSTMENT AFTER INSTALLATION
When replaced TCM, perform "ADDITIONAL SERVICE WHEN REPLACING TCM". Refer to
.
1.
Bracket
2.
TCM
:Vehicle front
: N·m (kg-m, in-lb)
JSDIA7186GB
Revision: November 2015
2016 JUKE
AIR BREATHER HOSE
TM-555
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
AIR BREATHER HOSE
Exploded View
INFOID:0000000012201249
Removal and Installation
INFOID:0000000012201250
REMOVAL
1. Remove air cleaner case. Refer to
EM-192, "Removal and Installation"
.
2. Remove clip of air breather hose from harness bracket.
3. Remove air breather hose from transaxle assembly.
INSTALLATION
Note the followings and installation is in the reverse order of removal.
CAUTION:
• Never bend the air breather hose to prevent damage to the hose.
• Insert air breather hose (1) to air breather tube (A) all the way
to the curve of the tube.
• Insert air breather hose to air breather tube so that the paint
mark (B) is facing upward.
1.
Air breather hose
2.
Clip
3.
Transaxle assembly
4.
Air breather tube
5.
Harness bracket
: Vehicle front
: Always replace after every disassembly.
JSDIA6058ZZ
JSDIA2399ZZ
Revision: November 2015
2016 JUKE
TM-556
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
AIR BREATHER HOSE
• Never reuse clip (A).
• Securely install the clip to the harness bracket.
JSDIA2458ZZ
Revision: November 2015
2016 JUKE
OIL PAN
TM-557
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OIL PAN
Exploded View
INFOID:0000000012201251
Removal and Installation
INFOID:0000000012201252
REMOVAL
1. Remove drain plug from oil pan and then drain the CVT fluid.
Transaxle assembly
Oil pan gasket
Magnet
Oil pan
Drain plug
Drain plug gasket
Overflow plug
O-ring
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Apply CVT fluid
JSDIA7928GB
JSDIA5205ZZ
Revision: November 2015
2016 JUKE
TM-558
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
OIL PAN
2. Remove drain plug gasket .
3. Remove oil pan bolts (
).
4. Remove oil pan from transaxle case.
5. Remove oil pan gasket from oil pan.
6. Remove magnets from oil pan.
INSTALLATION
Note the followings and installation is in the reverse order of removal.
CAUTION:
• Never reuse oil pan gasket.
• Never reuse drain plug gasket.
• Never reuse O-ring.
• Completely clean the iron powder from the magnet area of oil pan and the magnets.
• Install the oil pan to the transaxle case with the following procedure.
1. Install the oil pan gasket to the oil pan.
CAUTION:
JSDIA5206ZZ
: Vehicle front
JSDIA5207ZZ
JSDIA7929ZZ
JSDIA7930ZZ
Revision: November 2015
2016 JUKE
OIL PAN
TM-559
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Completely wipe out any moisture, oil, and old gasket from the oil pan gasket surface and bolt
hole of oil pan and transaxle case.
2. Install the oil pan assembly to the transaxle case, and then temporarily tighten the oil pan bolt.
3. Tighten the oil pan bolts in the order shown to the specified
torque.
4. Tighten the oil pan bolts again clockwise from (1) shown to the
specified torque.
• Fill with CVT fluid after installation. Refer to
.
Inspection
INFOID:0000000012201253
INSPECTION AFTER REMOVAL
Check oil pan for foreign material.
• If a large amount of worn material is found, clutch plate may be worn.
• If iron powder is found, bearings, gears, or clutch plates may be worn.
• If aluminum powder is found, bushing may be worn, or chips or burrs of aluminum casting parts may enter.
Check points where wear is found in all cases.
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of CVT fluid.
: Vehicle front
JSDIA5211ZZ
Revision: November 2015
2016 JUKE
TM-560
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
INPUT SPEED SENSOR
INPUT SPEED SENSOR
Exploded View
INFOID:0000000012201254
Removal and Installation
INFOID:0000000012201255
REMOVAL
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Turn ignition switch OFF.
2. Remove battery and battery support. Refer to
PG-105, "Removal and Installation"
.
3. Remove ECM and bracket as a set. Refer to
EC-1256, "Removal and Installation"
4. Disconnect input speed sensor connector.
5. Remove mounting bolt (
) and remove input speed sensor (1)
from transaxle assembly.
1.
Transaxle assembly
2.
O-ring
3.
Input speed sensor
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Apply CVT fluid
JSDIA6059GB
JSDIA6619ZZ
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст