Nissan Juke (2016 year). Service Repair Manual — part 128
AWD CONTROL MODULE
DLN-31
< ECU DIAGNOSIS INFORMATION >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• When there is a difference of revolution speed between the front and rear wheel the shift occasionally
changes to direct 4-wheel driving conditions automatically. This is not a malfunction.
DTC Inspection Priority Chart
INFOID:0000000012199371
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
DTC Index
INFOID:0000000012199372
Priority
Detected items (DTC)
1
P182D SOLENOID LEFT
2
P182E SOLENOID RIGHT
3
P1813 4WD MODE SW
4
P183B SOL POWER SUPPLY
5
P1811 BATTERY VOLTAGE
6
P1808 VHCL SPEED SEN-ABS
7
P1829 THROTTLE POSI SEN
8
U1010 CONTROL UNIT (CAN)
9
U1000 CAN COMM CIRCUIT
10
P1809 CONTROL UNIT 4
11
P1830 ABS OP SIG
12
P1831 VDC OP SIG
13
P1832 TCS OP SIG
14
P183C DECEL G SENSOR
15
P183D SIDE G SENSOR
16
P183E YAWRATE SENSOR
17
P1865 GEAR RATIO
18
P1840 OUTPUT SPEED SIGNAL
19
P1864 INPUT SPEED SIGNAL
20
P181E STR ANGLE SEN
21
P1820 ENGINE SPEED SIG
22
P181D ENGINE SYSTEM
23
P183F GEAR POSI SIGNAL
24
P181B INCOMP SELF SHUT
25
P1804 CONTROL UNIT 3
26
P181F INCOMP CALIBRATION
DTC
Items (CONSULT screen items)
Reference
P1804
CONTROL UNIT 3
P1808
VHCL SPEED SEN-ABS
P1809
CONTROL UNIT 4
P1811
BATTERY VOLTAGE
P1813
4WD MODE SW
P181B
INCOMP SELF SHUT
P181D
ENGINE SYSTEM
P181E
STR ANGLE SEN
P181F
INCOMP CALIBRATION
Revision: November 2015
2016 JUKE
DLN-32
< ECU DIAGNOSIS INFORMATION >
[TRANSFER: TY21B]
AWD CONTROL MODULE
NOTE:
If some DTCs are displayed at the same time, refer to
DLN-31, "DTC Inspection Priority Chart"
.
P1820
ENGINE SPEED SIG
P1829
THROTTLE POSI SEN
P182D
SOLENOID LEFT
P182E
SOLENOID RIGHT
P1830
ABS OP SIG
P1831
VDC OP SIG
P1832
TCS OP SIG
P183B
SOL POWER SUPPLY
P183C
DECEL G SENSOR
P183D
SIDE G SENSOR
P183E
YAWRATE SENSOR
P183F
GEAR POSI SIGNAL
P1840
OUTPUT SPEED SIGNAL
P1864
INPUT SPEED SIGNAL
P1865
GEAR RATIO
U1000
CAN COMM CIRCUIT
U1010
CONTROL UNIT (CAN)
DTC
Items (CONSULT screen items)
Reference
Revision: November 2015
2016 JUKE
AWD SYSTEM
DLN-33
< WIRING DIAGRAM >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
WIRING DIAGRAM
AWD SYSTEM
Wiring Diagram
INFOID:0000000012199373
JRDWC6642GB
Revision: November 2015
2016 JUKE
DLN-34
< WIRING DIAGRAM >
[TRANSFER: TY21B]
AWD SYSTEM
JRDWC6643GB
Revision: November 2015
2016 JUKE
AWD SYSTEM
DLN-35
< WIRING DIAGRAM >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
JRDWC6644GB
Revision: November 2015
2016 JUKE
DLN-36
< WIRING DIAGRAM >
[TRANSFER: TY21B]
AWD SYSTEM
JRDWC6645GB
Revision: November 2015
2016 JUKE
AWD SYSTEM
DLN-37
< WIRING DIAGRAM >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
JRDWC6646GB
Revision: November 2015
2016 JUKE
DLN-38
< BASIC INSPECTION >
[TRANSFER: TY21B]
DIAGNOSIS AND REPAIR WORK FLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow
INFOID:0000000012199374
DETAILED FLOW
1.
INTERVIEW FROM THE CUSTOMER
Clarify customer complaints before inspection. First of all, perform an interview utilizing
and reproduce symptoms as well as fully understand it. Ask customer about his/her complaints
carefully. Check symptoms by driving vehicle with customer, if necessary.
CAUTION:
Customers are not professional. Never guess easily like “maybe the customer means that...,” or
“maybe the customer mentions this symptom”.
>> GO TO 2.
2.
CHECK SYMPTOM
Reproduce the symptom that is indicated by the customer, based on the information from the customer
obtained by interview. Also check that the symptom is not caused by protection function. Refer to
CAUTION:
When the symptom is caused by normal operation, fully inspect each portion and obtain the under-
standing of customer that the symptom is not caused by a malfunction.
>> GO TO 3.
3.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is any DTC detected?
YES
>> Record or print self-diagnosis results. GO TO 4.
NO
>> GO TO 6.
4.
RECHECK SYMPTOM
With CONSULT
1. Erase self-diagnostic results for “ALL MODE AWD/4WD”.
2. Perform DTC confirmation procedures for the error detected system.
NOTE:
If some DTCs are detected at the same time, determine the order for performing the diagnosis based on
31, "DTC Inspection Priority Chart"
Is any DTC detected?
YES
>> GO TO 5.
NO
>> Check harness and connectors based on the information obtained by interview. Refer to
.
5.
REPAIR OR REPLACE ERROR-DETECTED PARTS
• Repair or replace error-detected parts.
• Reconnect part or connector after repairing or replacing.
• When DTC is detected, erase self-diagnostic results for “ALL MODE AWD/4WD”.
>> GO TO 7.
6.
IDENTIFY ERROR-DETECTED SYSTEM BY SYMPTOM DIAGNOSIS
Estimate error-detected system based on symptom diagnosis and perform inspection.
Can the error-detected system be identified?
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст