Nissan Juke (2016 year). Service Repair Manual — part 129
DIAGNOSIS AND REPAIR WORK FLOW
DLN-39
< BASIC INSPECTION >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
YES
>> GO TO 7.
NO
>> Check harness and connectors based on the information obtained by interview. Refer to
.
7.
FINAL CHECK
With CONSULT
1. Check the reference value for AWD control module.
2. Recheck the symptom and check that symptom is not reproduced on the same conditions.
Is the symptom reproduced?
YES
>> GO TO 3.
NO
>> INSPECTION END
Diagnostic Work Sheet
INFOID:0000000012199375
Description
• In general, customers have their own criteria for a problem. Therefore, it is important to understand the
symptom and status well enough by asking the customer about his/her concerns carefully. To systemize all
the information for the diagnosis, prepare the interview sheet referring to the interview points.
• In some cases, multiple conditions that appear simultaneously may cause a DTC to be detected.
Interview sheet sample
Interview sheet
Customer
name
MR/MS
Registration
number
Initial year
registration
Vehicle type
VIN
Storage date
Engine
Mileage
km (Mile)
Symptom
Vehicle does not enter AWD mode.
AWD warning lamp turns on.
Heavy tight-corner braking symptom occurs
Noise
Vibration
Decrease in turning performance.
Others
(
)
First occurrence
Recently
Others (
)
Frequency of occurrence
Always
Under a certain conditions of
Sometimes (time(s)/day)
Climate con-
ditions
Irrelevant
Weather
Fine
Cloud
Rain
Snow
Others (
)
Temperature
Hot
Warm
Cool
Cold
Temperature (Approx.
°
C)
Relative humidity
High
Moderate
Low
Road conditions
Urban area
Suburb area
High way
Mounting road (uphill or down hill)
Rough road
Operation conditions, etc.
Irrelevant
When engine starts
During idling
During driving
During acceleration
At constant speed driving
During deceleration
During cornering (right curve or left curve)
Revision: November 2015
2016 JUKE
DLN-40
< BASIC INSPECTION >
[TRANSFER: TY21B]
DIAGNOSIS AND REPAIR WORK FLOW
Other conditions
Memo
Interview sheet
Customer
name
MR/MS
Registration
number
Initial year
registration
Vehicle type
VIN
Storage date
Engine
Mileage
km (Mile)
Revision: November 2015
2016 JUKE
ADDITIONAL SERVICE WHEN REPLACING AWD CONTROL MODULE
DLN-41
< BASIC INSPECTION >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
ADDITIONAL SERVICE WHEN REPLACING AWD CONTROL MODULE
Description
INFOID:0000000012199376
When replacing AWD control module, unit characteristics writing is required. Refer to
.
Work Procedure
INFOID:0000000012199377
1.
PERFORM WRITING UNIT CHARACTERISTICS
Perform writing unit characteristics of electric controlled coupling.
>> Refer to
Revision: November 2015
2016 JUKE
DLN-42
< BASIC INSPECTION >
[TRANSFER: TY21B]
UNIT CHARACTERISTICS WRITING
UNIT CHARACTERISTICS WRITING
Description
INFOID:0000000012199378
When replacing AWD control module, rear final drive assembly and/or electric controlled coupling, unit charac-
teristics of electric controlled coupling writing is required. Refer to
Work Procedure
INFOID:0000000012199379
1.
UNIT CHARACTERISTICS WRITING
With CONSULT
1. Confirm the unit characteristics (A and B) of electric controlled
coupling (left and right).
NOTE:
• This illustration is sample.
• For the illustration, the unit characteristics are following.
2. Turn the ignition switch OFF to ON.
3. Select “UNIT CHARACTERISTICS WRITE” in “WORK SUP-
PORT” for “ALL MODE AWD/4WD”.
4. Input unit characteristics.
5. Select “Start”.
6. Check that “UNIT CHARACTERISTICS WRITE COMPLETED” is displayed.
>> WORK END
Left side:
3B4D66BBE32B
Right side:
3B4D66BBE318
JSDIA2079ZZ
Revision: November 2015
2016 JUKE
P1804, P1809 AWD CONTROL MODULE
DLN-43
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
DTC/CIRCUIT DIAGNOSIS
P1804, P1809 AWD CONTROL MODULE
DTC Logic
INFOID:0000000012199380
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1. Turn the ignition switch OFF to ON.
2. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P1804 or P1809” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012199381
1.
PERFORM SELF-DIAGNOSIS AGAIN
With CONSULT
Perform “DTC CONFIRMATION PROCEDURE” (self-diagnosis) again. Refer to
Is DTC “P1804 or 1809” detected?
YES
>> Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
.
NO
>> Check AWD control module pin terminals for damage or loose connection with harness connector.
If any items are damaged, repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P1804
CONTROL UNIT 3
Malfunction is detected in the memory
(EEPROM) system of AWD control mod-
ule.
Internal malfunction of AWD control
module.
P1809
CONTROL UNIT 4
AD converter system of AWD control
module is malfunctioning.
Revision: November 2015
2016 JUKE
DLN-44
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P1808 WHEEL SPEED SENSOR
P1808 WHEEL SPEED SENSOR
DTC Logic
INFOID:0000000012199382
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
2. Stop the vehicle.
3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P1808” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012199383
1.
PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
NO
>> GO TO 2.
2.
ERASE SELF-DIAGNOSTIC RESULT
With CONSULT
1. Erase self-diagnostic results for “ALL MODE AWD/4WD”.
2. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
3. Stop the vehicle.
4. Check that ABS warning lamp turns OFF.
Does ABS warning lamp turn OFF?
YES
>> GO TO 3.
NO
>> Refer to
BRC-136, "Component Function Check"
3.
CHECK TERMINALS AND HARNESS CONNECTORS
Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P1808”
is detected, Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P1808
VHCL SPEED SEN-ABS
• Malfunction is detected in vehicle
speed signal that is output from ABS
actuator and electric unit (control unit)
through CAN communication.
• Improper signal is input while driving.
• ABS actuator and electric unit (control
unit)
- Malfunction of ABS actuator and elec-
tric unit (control unit) circuit error
- Wheel speed sensor error
• AWD control module
• CAN communication line
Revision: November 2015
2016 JUKE
P1811 POWER SUPPLY CIRCUIT FOR AWD CONTROL MODULE
DLN-45
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
P1811 POWER SUPPLY CIRCUIT FOR AWD CONTROL MODULE
DTC Logic
INFOID:0000000012199384
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION
With CONSULT
1. Turn the ignition switch OFF to ON.
2. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P1811” detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012199385
1.
CHECK AWD CONTROL MODULE POWER SUPPLY (1)
1. Turn the ignition switch OFF.
2. Disconnect AWD control module harness connector.
3. Check the voltage between AWD control module harness connector and ground.
4. Turn the ignition switch ON.
CAUTION:
Never start the engine.
5. Check the voltage between AWD control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK AWD CONTROL MODULE POWER SUPPLY (2)
1. Turn the ignition switch OFF.
2. Check the 10A fuse (Except for NISMO RS models: #23, For NISMO RS models: #33).
3. Check the harness for open or short between AWD control module harness connector No.1 terminal and
10A fuse (Except for NISMO RS models: #23, For NISMO RS models: #33).
DTC
Display item
Malfunction detected condition
Possible cause
P1811
BATTERY VOLTAGE
When AWD control module power sup-
ply is lower or higher than normal
• Malfunction of AWD control module
power supply circuit (open or short)
• Malfunction of AWD control module
• Battery
AWD control module
—
Voltage
Connector
Terminal
B47
1
Ground
11 – 13 V
AWD control module
—
Voltage
Connector
Terminal
B47
1
Ground
11 – 13 V
Revision: November 2015
2016 JUKE
DLN-46
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P1811 POWER SUPPLY CIRCUIT FOR AWD CONTROL MODULE
Is the inspection result normal?
YES
>> Perform the trouble diagnosis for power supply circuit. Refer to
NO
>> Repair or replace error-detected parts.
3.
CHECK AWD CONTROL MODULE POWER SUPPLY (3)
1. Turn the ignition switch OFF.
2. Check the voltage between AWD control module harness connector and ground.
3. Turn the ignition switch ON.
CAUTION:
Never start the engine.
4. Check the voltage between AWD control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK AWD CONTROL MODULE POWER SUPPLY (4)
1. Turn the ignition switch OFF.
2. Check the 10A fuse (#3).
3. Check the harness for open or short between AWD control module harness connector No.3 terminal and
10A fuse (#3).
Is the inspection result normal?
YES
>> Perform the trouble diagnosis for ignition power supply circuit. Refer to
.
NO
>> Repair or replace error-detected parts.
5.
CHECK AWD CONTROL MODULE GROUND
1. Turn the ignition switch OFF.
2. Check the continuity between AWD control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace error-detected parts.
6.
CHECK TERMINALS AND HARNESS CONNECTORS
Check the AWD control module pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
>> Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
.
NO
>> Repair or replace error-detected parts.
AWD control module
—
Voltage
Connector
Terminal
B47
3
Ground
0 V
AWD control module
—
Voltage
Connector
Terminal
B47
3
Ground
11 – 13 V
AWD control module
—
Continuity
Connector
Terminal
B47
10
Ground
Existed
11
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст