Nissan Juke (2016 year). Service Repair Manual — part 377
SQUEAK AND RATTLE TROUBLE DIAGNOSES
EXT-9
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
1. Trunk lid dumpers out of adjustment
2. Trunk lid striker out of adjustment
3. Trunk lid torsion bars knocking together
4. A loose license plate or bracket
Most of these incidents can be repaired by adjusting, securing, or insulating the item(s) or component(s) caus-
ing the noise.
SUNROOF/HEADLINING
Noises in the sunroof / headlining area can often be traced to one of the following items:
1. Sunroof lid, rail, linkage, or seals making a rattle or light knocking noise
2. Sunvisor shaft shaking in the holder
3. Front or rear windshield touching headlining and squeaking
Again, pressing on the components to stop the noise while duplicating the conditions can isolate most of these
incidents. Repairs usually consist of insulating with felt cloth tape.
SEATS
When isolating seat noise it is important to note the position the seat is in and the load placed on the seat
when the noise occurs. These conditions should be duplicated when verifying and isolating the cause of the
noise.
Causes of seat noise include:
1. Headrest rods and holder
2. A squeak between the seat pad cushion and frame
3. The rear seatback lock and bracket
These noises can be isolated by moving or pressing on the suspected components while duplicating the con-
ditions under which the noise occurs. Most of these incidents can be repaired by repositioning the component
or applying urethane tape to the contact area.
UNDERHOOD
Some interior noise may be caused by components under the hood or on the engine wall. The noise is then
transmitted into the passenger compartment.
Causes of transmitted underhood noise include:
1. Any component mounted to the engine wall
2. Components that pass through the engine wall
3. Engine wall mounts and connectors
4. Loose radiator mounting pins
5. Hood bumpers out of adjustment
6. Hood striker out of adjustment
These noises can be difficult to isolate since they cannot be reached from the interior of the vehicle. The best
method is to secure, move, or insulate one component at a time and test drive the vehicle. Also, engine RPM
or load can be changed to isolate the noise. Repairs can usually be made by moving, adjusting, securing, or
insulating the component causing the noise.
Revision: November 2015
2016 JUKE
EXT-10
< SYMPTOM DIAGNOSIS >
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Diagnostic Worksheet
INFOID:0000000012199309
PIIB8740E
Revision: November 2015
2016 JUKE
SQUEAK AND RATTLE TROUBLE DIAGNOSES
EXT-11
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
PIIB8742E
Revision: November 2015
2016 JUKE
EXT-12
< REMOVAL AND INSTALLATION >
FRONT BUMPER
REMOVAL AND INSTALLATION
FRONT BUMPER
Exploded View
INFOID:0000000012199310
EXCEPT FOR NISMO AND NISMO RS
JMKIB4700GB
Revision: November 2015
2016 JUKE
FRONT BUMPER
EXT-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
NISMO
1.
Front side grille RH
2.
Front side grille LH
3.
Bumper side bracket RH
4.
Front center grille
5.
Emblem
6.
Bumper reinforcement
7.
Bumper energy absorber
8.
Bumper end rubber RH
9.
Bumper fascia
10. Screw grommet
11. Bumper bracket cover
12. License plate bracket
13. Front fog lamp bracket RH
(with front fog lamp)
14. Bumper finisher RH
(without front fog lamp)
15. U nut
16. Bumper fascia lower
17. Front fog lamp bracket LH
(with front fog lamp)
18. Bumper finisher LH
(without front fog lamp)
19. Bumper end rubber LH
20. Bumper retainer lower
21. Bumper side bracket LH
22. Screw grommet
23. Double-sided tape
[t: 1.2 mm (0.047 in)]
: Pawl
: Always replace after every disassembly.
, , , , , : Indicates that the part is connected at points with same symbol in actual vehicle.
Revision: November 2015
2016 JUKE
EXT-14
< REMOVAL AND INSTALLATION >
FRONT BUMPER
1.
Front upper grille
2.
Bumper side bracket RH
3.
Bumper reinforcement
4.
Front grille
5.
Emblem
6.
Bumper energy absorber
7.
Bumper end rubber RH
8.
Bumper fascia
9.
Screw grommet
10. Bumper bracket cover
11. License plate bracket
12. Bumper fascia lower
13. Daytime running light RH
14. Daytime running light LH
15. Front bumper finisher
16. Front bumper grille
17. Bumper end rubber LH
18. Bumper retainer lower
JMKIB4702GB
Revision: November 2015
2016 JUKE
FRONT BUMPER
EXT-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
NISMO RS
19. Bumper side bracket LH
20. Screw grommet
21. Double-sided tape
[t: 1.2 mm (0.047 in)]
22. U nut
: Pawl
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
, , , , , : Indicates that the part is connected at points with same symbol in actual vehicle.
Revision: November 2015
2016 JUKE
EXT-16
< REMOVAL AND INSTALLATION >
FRONT BUMPER
1.
Front upper grille
2.
Bumper side bracket RH
3.
Bumper reinforcement
4.
Front grille
5.
Emblem
6.
Bumper energy absorber
7.
Bumper end rubber RH
8.
Bumper fascia
9.
Screw grommet
10. Bumper bracket cover
11. License plate bracket
12. Bumper fascia lower
13. Daytime running light RH
14. Daytime running light LH
15. Front bumper finisher
16. Front bumper grille
17. Bumper end rubber LH
18. Bumper retainer lower
JMKIB4701GB
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст