Nissan Juke (2016 year). Service Repair Manual — part 378
FRONT BUMPER
EXT-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Removal and Installation
INFOID:0000000012199311
CAUTION:
Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with
oil.
REMOVAL
1. Fully open hood assembly.
2. Remove fixing clips (A) of bumper upper side.
3. Remove front fillet molding front side. Refer to
EXT-36, "FRONT FILLET MOLDING : Removal and Instal-
.
4. Remove bumper fascia fixing screws (A) (LH and RH).
5. Remove air guide mounting bolts, and then remove air guide (LH and RH). Refer to
.
6. Remove fixing clips of bumper lower side. (except for NISMO and NISMO RS)
7. Remove fixing screws of bumper lower side. (NISMO and NISMO RS)
8. Pull bumper fascia side toward the vehicle side to disengage the fitting of bumper side bracket and
bumper fascia side according to the numerical order 1
→
3 as shown by the arrows in the figure.
19. Bumper side bracket LH
20. Screw grommet
21. Double-sided tape
[t: 1.2 mm (0.047 in)]
22. U nut
: Pawl
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
, , , , , : Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIA5593ZZ
JMKIA5559ZZ
Revision: November 2015
2016 JUKE
EXT-18
< REMOVAL AND INSTALLATION >
FRONT BUMPER
• Except for NISMO and NISMO RS
CAUTION:
When removing bumper fascia assembly, 2 workers are
required so as to prevent it from dropping.
• NISMO and NISMO RS
CAUTION:
When removing bumper fascia assembly, 2 workers are
required so as to prevent it from dropping.
9. Disconnect front fog lamp harness connectors. (with front fog lamp)
10. Disconnect daytime running light harness connectors. (with daytime running light)
11. Remove bumper fascia assembly.
12. Remove the following parts after removing bumper fascia assembly.
• Daytime running light (LH and RH). Refer to
EXL-101, "Removal and Installation"
. (with daytime running
light)
• Front fog lamp (LH and RH). Refer to
EXL-102, "Removal and Installation"
. (with front fog lamp)
• Bumper finisher (LH and RH). (without front fog lamp)
• Front grille. Refer to
EXT-26, "Removal and Installation"
• Bumper fascia lower.
• Bumper end rubber (LH and RH).
• Bumper bracket cover.
• License plate bracket.
• Front bumper finisher. (NISMO and NISMO RS)
• Front bumper grille. (NISMO and NISMO RS)
13. Remove bumper energy absorber.
14. Remove bumper reinforcement mounting nuts, and then remove bumper reinforcement.
15. Remove bumper retainer lower fixing clips, and then remove bumper retainer lower.
16. Remove bumper side bracket fixing screws, and then remove bumper side bracket.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
NOTE:
• The following table shows the specified values for checking normal installation status.
• Fitting adjustment cannot be performed.
: Pawl
JMKIA5592ZZ
: Pawl
JMKIB4684ZZ
Revision: November 2015
2016 JUKE
FRONT BUMPER
EXT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Except for NISMO and NISMO RS
NISMO and NISMO RS
JMKIB4685ZZ
Portion
Clearance
Surface height difference
Bumper fascia assembly –
Hood
A – A
2.0 – 6.0 mm
(0.079 – 0.236 in)
(
−
2.5) – (+1.5) mm
[(
−
0.098) – (+0.059) in]
Bumper fascia assembly –
Front center grille
B – B
0.3 – 2.7 mm
(0.012 – 0.106 in)
—
Bumper fascia assembly –
Front side grille
C – C
0.3 – 2.7 mm
(0.012 – 0.106 in)
—
Bumper fascia assembly –
Front combination lamp
D – D
0.5 – 3.5 mm
(0.020 – 0.138 in)
—
Bumper fascia assembly –
Front fender
E – E
0.3 – 1.0 mm
(0.012 –0.039 in)
(
−
0.3) – (+1.7) mm
[(
−
0.012) – (+0.067) in]
JSKIA3162GB
Portion
Clearance
Surface height difference
Bumper fascia assembly –
Hood
A – A
2.0 – 6.0 mm
(0.079 – 0.236 in)
(
−
2.0) – (+1.0) mm
[(
−
0.079) – (+0.039) in]
Bumper fascia assembly –
Front grille
B – B
0.3 – 2.7 mm
(0.012 – 0.106 in)
—
C – C
0.5 – 1.5 mm
(0.020 – 0.059 in)
0.0 – 1.0 mm
(0.000 – 0.039 in)
Bumper fascia assembly –
Front combination lamp
D – D
0.5 – 3.5 mm
(0.020 – 0.138 in)
—
Bumper fascia assembly –
Front fender
E – E
0.3 – 1.0 mm
(0.012 –0.039 in)
(
−
0.3) – (+1.7) mm
[(
−
0.012) – (+0.067) in]
Revision: November 2015
2016 JUKE
EXT-20
< REMOVAL AND INSTALLATION >
REAR BUMPER
REAR BUMPER
Exploded View
INFOID:0000000012199312
EXCEPT FOR NISMO AND NISMO RS
JMKIB4703ZZ
Revision: November 2015
2016 JUKE
REAR BUMPER
EXT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
NISMO AND NISMO RS
1.
Bumper side bracket LH
2.
Bumper closing LH
3.
Bumper fascia assembly
4.
Rear panel lower
5.
U nut
6.
Bumper fascia lower
7.
Reflex reflector LH
8.
Reflex reflector RH
9.
Bumper energy absorber
10. Bumper reinforcement
11. Screw grommet
12. Bumper closing RH
13. Bumper side bracket RH
A.
: 4WD models
: Pawl
, , , , , , , , : Indicates that the part is connected at points with same symbol in actual vehicle.
Revision: November 2015
2016 JUKE
EXT-22
< REMOVAL AND INSTALLATION >
REAR BUMPER
1.
Bumper side bracket LH
2.
Bumper closing LH
3.
Bumper spacer
4.
U nut
5.
Bumper fascia
6.
Bumper fascia lower
7.
Reflex reflector LH
8.
Rear fog lamp housing
9.
Reflex reflector RH
10. Bumper energy absorber
11. Bumper reinforcement
12. Screw grommet
13. Bumper closing RH
14. Bumper stay RH
A.
: 4WD models
JMKIB4704ZZ
Revision: November 2015
2016 JUKE
REAR BUMPER
EXT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Removal and Installation
INFOID:0000000012199313
CAUTION:
Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with
oil.
REMOVAL
1. Fully open back door.
2. Remove bumper fascia fixing screws of rear combination lamp lower side (LH and RH).
3. Remove rear fillet molding rear side. Refer to
EXT-37, "REAR FILLET MOLDING : Removal and Installa-
4. Remove bumper closing (LH and RH).
5. Remove fixing clips of bumper lower side.
6. Remove bumper fascia fixing screws (A) (LH and RH).
7. Pull bumper fascia side toward the vehicle side to disengage the
fitting of bumper side bracket and bumper fascia side according
to the numerical order 1
→
3 as shown by the arrows in the fig-
ure.
CAUTION:
When removing bumper fascia, 2 workers are required so
as to prevent it from dropping.
8. Remove bumper fascia.
9. Remove the following parts after removing bumper fascia.
• Reflex reflector (LH and RH). Refer to
EXL-116, "Removal and Installation"
.
• Bumper fascia lower
• Rear fog lamp housing (NISMO and NISMO RS). Refer to
EXL-115, "Removal and Installation"
10. Remove bumper energy absorber.
11. Remove bumper reinforcement mounting nuts, and then remove bumper reinforcement.
12. Remove rear panel lower.
13. Remove bumper side bracket fixing screws, and then remove bumper side bracket (LH and RH).
INSTALLATION
Note the following items, and then install in the reverse order of removal.
NOTE:
• The following table shows the specified values for checking normal installation status.
• Fitting adjustment cannot be performed.
: Pawl
: Always replace after every disassembly.
, , , , , , :
Indicates
that
the
part
is
connected
at points with same symbol in actual vehicle.
JMKIA5561ZZ
: Pawl
JMKIA5564ZZ
Revision: November 2015
2016 JUKE
EXT-24
< REMOVAL AND INSTALLATION >
REAR BUMPER
Except for NISMO and NISMO RS
NISMO and NISMO RS
JMKIB4687ZZ
Portion
Clearance
Surface height difference
Bumper fascia assembly –
Rear fender
A – A
0.3 – 1.1 mm
(0.012 – 0.043 in)
(
−
0.3) – (+1.7) mm
[(
−
0.012) – (+0.067) in]
Bumper fascia assembly –
Rear combination lamp
B – B
0.2 – 2.8 mm
(0.008 – 0.110 in)
—
Bumper fascia assembly –
Back door
C – C
3.0 – 7.0 mm
(0.118 – 0.276 in)
0.0 – 4.0 mm
(0.000 – 0.157 in)
D – D
6.0 – 10.0 mm
(0.236 – 0.394 in)
—
JMKIB4688ZZ
Portion
Clearance
Surface height difference
Bumper fascia assembly –
Rear fender
A – A
0.0 – 1.0 mm
(0.000 – 0.039 in)
(
−
0.3) – (+1.7) mm
[(
−
0.012) – (+0.067) in]
Bumper fascia assembly –
Rear combination lamp
B – B
0.2 – 3.0 mm
(0.008 – 0.118 in)
—
Bumper fascia assembly –
Back door
C – C
3.0 – 7.0 mm
(0.118 – 0.276 in)
0.0 – 4.0 mm
(0.000 – 0.157 in)
D – D
6.0 – 10.0 mm
(0.236 – 0.394 in)
0.0 – 4.0 mm
(0.000 – 0.157 in)
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст