Nissan Juke (2016 year). Service Repair Manual — part 496
SQUEAK AND RATTLE TROUBLE DIAGNOSES
MIR-13
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
1. Trunk lid dumpers out of adjustment
2. Trunk lid striker out of adjustment
3. Trunk lid torsion bars knocking together
4. A loose license plate or bracket
Most of these incidents can be repaired by adjusting, securing, or insulating the item(s) or component(s) caus-
ing the noise.
SUNROOF/HEADLINING
Noises in the sunroof / headlining area can often be traced to one of the following items:
1. Sunroof lid, rail, linkage, or seals making a rattle or light knocking noise
2. Sunvisor shaft shaking in the holder
3. Front or rear windshield touching headlining and squeaking
Again, pressing on the components to stop the noise while duplicating the conditions can isolate most of these
incidents. Repairs usually consist of insulating with felt cloth tape.
SEATS
When isolating seat noise it is important to note the position the seat is in and the load placed on the seat
when the noise occurs. These conditions should be duplicated when verifying and isolating the cause of the
noise.
Causes of seat noise include:
1. Headrest rods and holder
2. A squeak between the seat pad cushion and frame
3. The rear seatback lock and bracket
These noises can be isolated by moving or pressing on the suspected components while duplicating the con-
ditions under which the noise occurs. Most of these incidents can be repaired by repositioning the component
or applying urethane tape to the contact area.
UNDERHOOD
Some interior noise may be caused by components under the hood or on the engine wall. The noise is then
transmitted into the passenger compartment.
Causes of transmitted underhood noise include:
1. Any component mounted to the engine wall
2. Components that pass through the engine wall
3. Engine wall mounts and connectors
4. Loose radiator mounting pins
5. Hood bumpers out of adjustment
6. Hood striker out of adjustment
These noises can be difficult to isolate since they cannot be reached from the interior of the vehicle. The best
method is to secure, move, or insulate one component at a time and test drive the vehicle. Also, engine RPM
or load can be changed to isolate the noise. Repairs can usually be made by moving, adjusting, securing, or
insulating the component causing the noise.
Revision: November 2015
2016 JUKE
MIR-14
< SYMPTOM DIAGNOSIS >
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Diagnostic Worksheet
INFOID:0000000012201506
PIIB8740E
Revision: November 2015
2016 JUKE
SQUEAK AND RATTLE TROUBLE DIAGNOSES
MIR-15
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
PIIB8742E
Revision: November 2015
2016 JUKE
MIR-16
< REMOVAL AND INSTALLATION >
INSIDE MIRROR
REMOVAL AND INSTALLATION
INSIDE MIRROR
Exploded View
INFOID:0000000012201507
Removal and Installation
INFOID:0000000012201508
CAUTION:
Never reuse the inside mirror assembly disassembled from mirror base.
REMOVAL
Slide the inside mirror assembly upward to remove.
NOTE:
Insert flat-bladed screwdriver (A) under the inside mirror (1).
Slide the inside mirror to the upper side while pushing the pawl
downward.
CAUTION:
Never use excessive force to remove the inside mirror because
it is inserted tightly into the mirror base.
INSTALLATION
Install in the reverse order of removal.
1.
Windshield glass
2.
Mirror base
3.
Inside mirror assembly
: Always replace after every disassembly.
JMLIA0400ZZ
: Always replace after every disassembly.
JMLIA0055ZZ
Revision: November 2015
2016 JUKE
OUTSIDE MIRROR
MIR-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
OUTSIDE MIRROR
Exploded View
INFOID:0000000012201509
DOOR MIRROR ASSEMBLY
DOOR MIRROR ASSEMBLY : Removal and Installation
INFOID:0000000012201510
CAUTION:
When removing, always use a remover tool that is made of plastic.
REMOVAL
1.
Door mirror cover
2.
Side turn signal lamp
3.
Door mirror finisher
(without around view monitor sys-
tem)
4.
Door mirror actuator
5.
Glass mirror
6.
Door mirror corner cover
7.
Door mirror housing
8.
Side camera assembly
(with around view monitor system)
9.
Side camera finisher
(with around view monitor system)
: Clip
: Pawl
N·m (kg-m, in-lb)
JMLIA6142GB
Revision: November 2015
2016 JUKE
MIR-18
< REMOVAL AND INSTALLATION >
OUTSIDE MIRROR
1. Disengage door mirror corner cover fixing clips using a remover
tool (A), and then remove door mirror corner cover.
2. Remove front door finisher. Refer to
INT-13, "Removal and Installation"
3. Disconnect door mirror harness connector.
4. Remove door mirror mounting nuts, and then remove door mirror assembly.
INSTALLATION
Install in the reverse order of removal.
DOOR MIRROR ASSEMBLY : Disassembly and Assembly
INFOID:0000000012201511
DISASSEMBLY
1. Remove door mirror assembly. Refer to
MIR-17, "DOOR MIRROR ASSEMBLY : Removal and Installa-
2. Remove glass mirror. Refer to
MIR-19, "GLASS MIRROR : Removal and Installation"
.
3. Remove door mirror actuator mounting bolts (A), and disconnect
harness connector (B), and then remove door mirror actuator.
4. Disengage door mirror cover and door mirror finisher (without around view monitor system) or side cam-
era finisher (with around view monitor system). Refer to
MIR-20, "DOOR MIRROR COVER : Removal and
.
5. Disconnect side camera harness connector (with around view monitor system).
6. Remove side camera bracket fixing screws (A), and then
remove side camera assembly from door mirror finisher. (with
around view monitor system)
7. Remove side turn signal lamp. Refer to the following.
• Xenon type: Refer to
EXL-104, "Removal and Installation"
• Halogen type: Refer to
EXL-215, "Removal and Installation"
ASSEMBLY
Note the following item, and then assemble in the reverse order of disassembly.
: Clip
JMLIA1391ZZ
JMLIA5685ZZ
JMLIA5689ZZ
Revision: November 2015
2016 JUKE
OUTSIDE MIRROR
MIR-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
CAUTION:
Perform side camera image calibration (with side camera). Refer to
IMAGE (AROUND VIEW MONITOR) : Description"
GLASS MIRROR
GLASS MIRROR : Removal and Installation
INFOID:0000000012201512
REMOVAL
1. Place the glass mirror inward.
2. Apply protective tape (A) on door mirror housing and glass mir-
ror to protect it from damage.
3. Insert remover tool (A) into the recess at outside between glass mirror and door mirror actuator, and then
disengage the door mirror fixing pawls.
CAUTION:
Remove the pawls slowly so they are not damaged.
NOTE:
Insert remover tool into recesses,and push up while rotating (twisting) to make work easier.
4. Disconnect heater mirror terminals (A). (with heater mirror)
CAUTION:
Make a mark (short note, photo, etc.) of terminals layout,
before disassembly.
5. Remove glass mirror.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
After installation, visually check that pawls are securely engaged.
JMLIA5703ZZ
JMLIA5704ZZ
JMLIA4194ZZ
Revision: November 2015
2016 JUKE
MIR-20
< REMOVAL AND INSTALLATION >
OUTSIDE MIRROR
DOOR MIRROR COVER
DOOR MIRROR COVER : Removal and Installation
INFOID:0000000012201513
REMOVAL
1. Remove the glass mirror. Refer to
MIR-19, "GLASS MIRROR : Removal and Installation"
2. Remove door mirror finisher (without around view monitor sys-
tem) or side camera finisher (with around view monitor system)
fixing screws (A), disengage door mirror cover and door mirror
finisher (without around view monitor system) or side camera
finisher (with around view monitor system) fixing pawls pushed
in the direction of the arrows as shown in figure.
3. Disengage door mirror cover fixing pawls, and then remove door
mirror cover (1) and door mirror finisher (without around view
monitor system) or side camera finisher (with around view moni-
tor system) (2).
4. Disconnect side camera harness connector. (with around view monitor system)
5. Disengage door mirror cover fixing pawls, remove door mirror
cover (1) from door mirror finisher (without around view monitor
system) or side camera finisher (with around view monitor sys-
tem) (2) indicated by arrows as shown in the figure.
INSTALLATION
Note the following item and then install in the reverse order of removal.
CAUTION:
After installation, visually check that pawls are securely engaged.
JMLIA5686ZZ
: Pawl
JMLIA5687ZZ
JMLIA5688ZZ
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст