Nissan Juke (2016 year). Service Repair Manual — part 540
RAX-14
< PERIODIC MAINTENANCE >
[AWD]
REAR WHEEL HUB AND HOUSING
PERIODIC MAINTENANCE
REAR WHEEL HUB AND HOUSING
Inspection
INFOID:0000000012196559
COMPONENT PART
Check the mounting conditions (looseness, back lash) of each component and component conditions (wear,
damage) are normal.
WHEEL HUB ASSEMBLY (BEARING-INTEGRATED TYPE)
Check the following items, and replace the part it necessary.
• Move wheel hub assembly in the axial direction by hand. Check there is no looseness of wheel bearing.
• Rotate wheel hub assembly and check there is no unusual noise or other irregular conditions. If there is any
of irregular conditions, replace wheel hub assembly.
Axial end play
: Refer to
Revision: November 2015
2016 JUKE
REAR DRIVE SHAFT
RAX-15
< PERIODIC MAINTENANCE >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
REAR DRIVE SHAFT
Inspection
INFOID:0000000012196560
• Check drive shaft mounting point and joint for looseness and other damage.
• Check boot for cracks and other damage.
CAUTION:
Replace entire drive shaft assembly when noise or vibration occur from drive shaft.
Revision: November 2015
2016 JUKE
RAX-16
< REMOVAL AND INSTALLATION >
[AWD]
REAR WHEEL HUB AND HOUSING
REMOVAL AND INSTALLATION
REAR WHEEL HUB AND HOUSING
Exploded View
INFOID:0000000012196561
Removal and Installation
INFOID:0000000012196562
REMOVAL
1. Remove tires with power tool. Refer to
WT-39, "Removal and Installation"
.
2. Remove wheel sensor. Refer to
BRC-150, "REAR WHEEL SENSOR : Removal and Installation"
.
3. Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work. Refer to
BR-64, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
CAUTION:
Never depress brake pedal while brake caliper is removed.
4. Remove disc rotor. If disc rotor cannot be removed, remove as follows.
CAUTION:
• Parking brake completely in the released position.
• Put matching marks (A) on the wheel hub assembly and
the disc rotor before removing the disc rotor.
• Never drop disc rotor.
a. Fix the disc rotor with wheel nuts and remove the adjusting hole
plug.
1.
Axle housing
2.
Suspension arm
3.
Parking brake assembly
4.
Hub bolt
5.
Wheel hub assembly (Bearing-inte-
grated type)
6.
Disc rotor
7.
Plug
8.
Wheel hub lock nut
9.
Cotter pin
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JPDIG0202GB
JPDIG0066ZZ
Revision: November 2015
2016 JUKE
REAR WHEEL HUB AND HOUSING
RAX-17
< REMOVAL AND INSTALLATION >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
b. Using suitable tool, rotate adjuster (1) in the direction (A) to
retract and loosen brake shoe.
c. Remove disc rotor.
5. Remove cotter pin, and then loosen wheel hub lock nut with
power tool.
6. Patch wheel hub lock nut with a piece of wood. Hammer the
wood to disengage wheel hub assembly from drive shaft.
CAUTION:
• Never place drive shaft joint at an extreme angle. Also be
careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for
joint sub-assembly, shaft and the other parts.
NOTE:
Use suitable puller, if wheel hub assembly and drive shaft can-
not be separated even after performing the above procedure.
7. Remove wheel hub lock nut.
8. Remove wheel hub assembly.
CAUTION:
Never remove parking brake assembly. Protect it from falling.
9. If axle housing need to be removed, remove drive shaft. Refer to
RAX-19, "Removal and Installation"
.
10. Remove hub bolts (1) from wheel hub assembly, using the ball
joint remover (A) (commercial service tool).
CAUTION:
• Remove hub bolt only when necessary.
• Never hammer the hub bolt to avoid impact to the wheel
hub assembly.
• Pull out the hub bolt in a direction perpendicular to the
wheel hub assembly.
11. Perform inspection after removal. Refer to
INSTALLATION
Note the following, and install in the reverse order of the removal.
• Place a washer (A) as shown in the figure to install the hub bolts
(1) by using the tightening force of the nut (B).
CAUTION:
• Check that there is no clearance between wheel hub assem-
bly and hub bolt.
• Never reuse hub bolt.
• Never reuse wheel hub lock nut and cotter pin.
• Align the matching marks that have been made during removal
when reusing the disc rotor.
• Perform inspection after installation. Refer to
Inspection
INFOID:0000000012196563
INSPECTION AFTER REMOVAL
Check wheel hub assembly for wear, cracks, and damage. Replace if necessary.
INSPECTION AFTER INSTALLATION
JPDIG0204ZZ
JPDIG0070ZZ
JPDIF0299ZZ
JPDIF0300ZZ
Revision: November 2015
2016 JUKE
RAX-18
< REMOVAL AND INSTALLATION >
[AWD]
REAR WHEEL HUB AND HOUSING
1. Check wheel sensor harness for proper connection.
BRC-148, "REAR WHEEL SENSOR : Exploded
.
2. Adjust parking brake operation (stroke). Refer to
PB-4, "Inspection and Adjustment"
.
3. Check wheel alignment. Refer to
4. Adjust neutral position of steering angle sensor. Refer to
.
Revision: November 2015
2016 JUKE
REAR DRIVE SHAFT
RAX-19
< REMOVAL AND INSTALLATION >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
REAR DRIVE SHAFT
Exploded View
INFOID:0000000012196564
Removal and Installation
INFOID:0000000012196565
REMOVAL
1. Remove tires with power tool. Refer to
WT-39, "Removal and Installation"
.
2. Remove wheel sensor. Refer to
BRC-150, "REAR WHEEL SENSOR : Removal and Installation"
.
3. Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work. Refer to
BR-64, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
CAUTION:
Never depress brake pedal while brake caliper is removed.
4. Remove disc rotor. Refer to
RAX-16, "Removal and Installation"
5. Remove cotter pin, and then loosen wheel hub lock nut with power tool. Refer to
.
6. Patch wheel hub lock nut with a piece of wood. Hammer the
wood to disengage wheel hub assembly from drive shaft.
CAUTION:
• Never place drive shaft joint at an extreme angle. Also be
careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for
joint sub-assembly, shaft and the other parts.
NOTE:
Use suitable puller, if wheel hub assembly and drive shaft can-
not be separated even after performing the above procedure.
7. Remove wheel hub lock nut.
8. Set jack under suspension arm.
1.
Circular clip
2.
Dust shield
3.
Housing
4.
Snap ring
5.
Ball cage/steel ball/inner race as-
sembly
6.
Stopper ring
7.
Boot band
8.
Boot
9.
Shaft
10. Joint sub-assembly
11. Sensor rotor
: Wheel side
: Fill NISSAN genuine grease or an equivalent.
: Always replace after every disassembly.
JPDIG0207ZZ
JPDIG0070ZZ
Revision: November 2015
2016 JUKE
RAX-20
< REMOVAL AND INSTALLATION >
[AWD]
REAR DRIVE SHAFT
CAUTION:
• Never damage the suspension arm with a jack.
• Check the stable condition when using a jack.
9. Remove stabilizer link. Refer to
RSU-35, "Removal and Installation"
10. Remove shock absorber from suspension arm. Refer to
RSU-24, "Removal and Installation"
.
11. Remove upper link from suspension arm. Refer to
RSU-33, "Removal and Installation"
.
12. Remove lower link from suspension arm. Refer to
RSU-31, "Removal and Installation"
13. Remove drive shaft from final drive assembly.
CAUTION:
Confirm that the circular clip is attached to the drive shaft.
14. Perform inspection after removal. Refer to
INSTALLATION
Note the following, and install in the reverse order of removal.
• Place the protector (A) [SST:KV38107900 ( — )] onto final drive
assembly to prevent damage to the oil seal while inserting drive
shaft. Slide drive shaft sliding joint and tap with a hammer to install
securely.
CAUTION:
Check that circular clip is completely engaged.
• Perform final tightening of bolts and nuts at suspension arm (rub-
ber bushing), under unladen conditions with tires on level ground.
• Perform inspection after installation. Refer to
.
WHEEL SIDE
WHEEL SIDE : Disassembly and Assembly
INFOID:0000000012196566
DISASSEMBLY
1. Fix shaft with a vise.
CAUTION:
Protect shaft using aluminum or copper plates when fixing with a vise.
2. If sensor rotor needs to be removed, use a bearing replacer (A)
and puller (B).
3. Remove boot bands. Then remove boot from joint sub-assem-
bly.
4. Screw drive shaft puller (A) (commercial service tool) into joint
sub-assembly screw part to a length of 30 mm (1.18 in) or more.
Support drive shaft with one hand and pull out joint sub-assem-
bly from shaft.
CAUTION:
• Align drive shaft puller and drive shaft and remove them
by pulling firmly and uniformly.
• If joint sub-assembly cannot be removed after five or
more unsuccessful attempts, replace shaft and joint sub
assembly as a set.
5. Remove circular clip from shaft.
6. Remove boot from shaft.
JPDIF0023ZZ
JPDIG0016ZZ
JPDIG0151ZZ
Revision: November 2015
2016 JUKE
REAR DRIVE SHAFT
RAX-21
< REMOVAL AND INSTALLATION >
[AWD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
7. Perform inspection after disassembly. Refer to
.
ASSEMBLY
1. If sensor rotor (1) is removed, use a drift (A) [SST:KV38100500 (
— )] and color (B) [SST:KV40101840 ( — )] to press in a new
one.
CAUTION:
Never reuse sensor rotor.
2. Clean the old grease on joint sub-assembly with paper waste.
3. Fill serration slot joint sub-assembly (1) with NISSAN genuine
grease or equivalent until the serration slot and ball groove
become full to the brim.
CAUTION:
After applying grease, use a shop cloth to wipe off old
grease that has oozed out.
4. Install boot and boot bands to shaft.
CAUTION:
• Wrap serration on shaft with tape (A) to protect the boot
from damage.
• Never reuse boot and boot band.
5. Remove the tape wrapped around the serrated on shaft.
6. Position the circular clip (1) on groove at the shaft edge.
CAUTION:
Never reuse circular clip.
NOTE:
Drive joint inserter is recommended when installing circular clip.
7. Align both center axles of the shaft edge and joint sub-assembly.
Then assemble shaft with joint sub-assembly holding circular
clip.
PDIA1182J
JPDIF0008ZZ
JPDIF0009ZZ
JPDIF0305ZZ
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст