Nissan Pathfinder (2006 year). Manual — part 76
NAVIGATION SYSTEM
AV-99
C
D
E
F
G
H
I
J
L
M
A
B
AV
2006 Pathfinder
51 (B)
49
RGB area
(YS) signal
Output
ON
Press the“TRIP”
button.
RGB screen is
not shown.
52 (R/W)
47
RGB signal
(G: green)
Output
ON
Select “Display
Diagnosis (DCU)” of
CONFIRMATION/
ADJUSTMENT
function.
Screen looks
reddish.
53 (W)
49
Vertical syn-
chronizing
(VP) signal
Input
ON
–
Operating
screen for audio
and A/C is not
displayed when
showing NAVI
screen.
54 (B)
47
RGB signal
(B: blue)
Output
ON
Select “Display
Diagnosis (DCU)” of
CONFIRMATION/
ADJUSTMENT
function.
Screen looks
yellowish.
55 (R)
49
Horizontal
synchroniz-
ing (HP) sig-
nal
Input
ON
–
Operating
screen for audio
and A/C is not
displayed when
showing NAVI
screen.
56 (G)
49
RGB syn-
chronizing
signal
Output
ON
Press the “TRIP”
button.
NAVI screen is
rolling.
Terminal No.
(Wire color)
Item
Signal
input/
output
Condition
Voltage
(Approx.)
Example of
symptom
+
–
Igni-
tion
switch
Operation
SKIA0162E
SKIA4981E
SKIA4983E
SKIA4982E
SKIA4983E
SKIA0164E
AV-100
NAVIGATION SYSTEM
2006 Pathfinder
Terminals and Reference Value for Display Unit
EKS00G6M
Terminal No. (Wire
color)
Item
Signal
input/
output
Condition
Voltage
(Approx.)
Example of
symptom
+
–
Igni-
tion
switch
Operation
1 (B)
Ground
Ground
–
ON
–
0V
–
2 (L)
Ground
Power sup-
ply (Inverter)
Input
ON
–
9V
Screen is not
shown.
3 (O)
Ground
Power sup-
ply (Signal)
Input
ON
–
9V
Screen is not
shown.
6 (R/W)
7
RGB signal
(G: green)
Input
ON
Select “Display
Diagnosis (DCU)” of
CONFIRMATION/
ADJUSTMENT
function.
Screen looks
reddish.
7
–
Shield
ground
–
–
–
–
–
8 (R)
21
Horizontal
synchroniz-
ing (HP) sig-
nal
Output
ON
–
Operating
screen for audio
and A/C is not
displayed when
showing NAVI
screen.
9 (B)
21
RGB area
(YS) signal
Input
ON
Press the “TRIP”
button.
Operating
screen for audio
and A/C is not
displayed when
showing NAVI
screen.
11 (B/W)
23
Display com-
munication
signal
(DCU-DSP)
Input
ON
–
Though a screen
is displayed, it is
impossible to
adjust bright-
ness.
13 (P)
Ground
(Inverter)
Ground
–
ON
–
0V
–
14 (SB)
Ground
(Signal)
Ground
–
ON
–
0V
–
17 (R/L)
7
RGB signal
(R: red)
Input
ON
Select “Display
Diagnosis (DCU)” of
CONFIRMATION/
ADJUSTMENT
function.
Screen looks
bluish.
SKIA4981E
SKIA4983E
SKIA0162E
SKIA4364E
SKIA4980E
NAVIGATION SYSTEM
AV-101
C
D
E
F
G
H
I
J
L
M
A
B
AV
2006 Pathfinder
18 (B)
7
RGB signal
(B: blue)
Input
ON
Select “Display
Diagnosis (DCU)” of
CONFIRMATION/
ADJUSTMENT
function.
Screen looks
yellowish.
19 (G)
21
RGB syn-
chronizing
signal
Input
ON
Press the “TRIP”
button.
NAVI screen is
rolling.
20 (W)
21
Vertical syn-
chronizing
(VP) signal
Output
ON
–
Operating
screen for audio
and A/C is not
displayed when
showing NAVI
screen.
21
–
Shield
ground
–
–
–
–
–
22 (L)
23
Display com-
munication
signal
(DSP-DCU)
Output
ON
–
Though a screen
is displayed, it is
impossible to
adjust bright-
ness.
23
–
Shield
ground
–
–
–
–
–
Terminal No. (Wire
color)
Item
Signal
input/
output
Condition
Voltage
(Approx.)
Example of
symptom
+
–
Igni-
tion
switch
Operation
SKIA4982E
SKIA0164E
SKIA4983E
SKIA4363E
AV-102
NAVIGATION SYSTEM
2006 Pathfinder
Terminals and Reference Value for AV Switch
EKS00G6N
Terminal No.
(Wire color)
Item
Signal
input/
output
Condition
Voltage
(Approx.)
Example of
symptom
+
–
Ignition
switch
Operation
1 (Y)
Ground
Battery
power
Input
OFF
–
Battery voltage
System does not
work properly.
2 (G/B)
Ground
ACC power
Input
ACC
–
Battery voltage
System does not
work properly.
3 (R)
Ground
Illumination
signal
Input
OFF
Lighting switch is
ON (position 1).
Battery voltage
AV switch illumi-
nation does not
come on when
lighting switch is
ON (position 1).
Turn lighting switch
OFF.
3.0V or less
4 (BR)
Ground
Illumination
control signal
Input
ON
Illumination control
switch is operated
by lighting switch in
1st position.
Changes between 0 and 12V
AV switch illumi-
nation cannot be
controlled.
5 (B)
Ground
Ground
–
ON
–
0V
–
6 (V)
Ground
Communica-
tion signal (+)
Input/
output
ON
–
System does not
work properly.
7
–
Shield
ground
–
–
–
–
–
8 (LG)
Ground
Communica-
tion signal (-)
Input/
output
ON
–
System does not
work properly.
12 (R)
Ground
Remote con-
trol A
Input
ON
Press MODE switch
0V
Steering wheel
audio controls
do not function.
Press SEEK UP
switch
0.75V
Press VOL UP
switch
2V
Except for above
5V
13 (GR)
Ground
Remote con-
trol B
Input
ON
Press POWER
switch
0V
Steering wheel
audio controls
do not function.
Press SEEK DOWN
switch
0.75V
Press VOL DOWN
switch
2V
Except for above
5V
14 (L)
–
Remote con-
trol ground
–
–
–
–
Steering wheel
audio controls
do not function.
SKIA0175E
SKIA0176E
NAVIGATION SYSTEM
AV-103
C
D
E
F
G
H
I
J
L
M
A
B
AV
2006 Pathfinder
Terminals and Reference Value for BCM
EKS00G6O
Refer to
BCS-12, "Terminals and Reference Values for BCM"
On Board Self-Diagnosis Function
EKS00G6P
DESCRIPTION
●
Diagnosis function consists of the self-diagnosis mode performed automatically and the CONFIRMATION/
ADJUSTMENT mode operated manually.
●
Self-diagnosis mode checks for connections between the units constituting this system, analyzes each
individual unit at the same time, and displays the results on the LCD screen.
●
CONFIRMATION/ADJUSTMENT mode is used to perform trouble diagnosis that require operation and
judgment by an operator (trouble that cannot be automatically judged by the system), to check/change the
set value, and to display the History of Errors of the navigation system.
DIAGNOSIS ITEM
NOTE:
Make the status that is set by D/N function be shown.
Mode
Description
Self-diagnosis (DCU)
●
Display control unit diagnosis.
●
Perform connection diagnosis and unit diagnosis between display con-
trol unit and each unit.
Self-diagnosis (NAVI)
●
NAVI Control unit diagnosis (DVD-ROM drive) will not be diagnosed
when no map DVD-ROM is in it.
●
Analyzes connection between the NAVI control unit and the GPS
antenna and operation of each unit.
CONFIRMATION/
ADJUSTMENT
Display diagnosis
On display control unit mode, color tone and shading of the screen can be
checked by the display of a color bar and a gray scale.
Vehicle signals
On display control unit mode, analyzes the following vehicle signals: Vehi-
cle speed signal, light signal
NOTE
, ignition switch signal, and reverse sig-
nal.
Auto Climate Control
A/C self-diagnosis of A/C system.
Navigation
Display diagnosis
On NAVI C/U mode, color tone and shading of the screen can be checked
by the display of a color bar and a gray scale.
Vehicle signals
On NAVI C/U mode, analyzes the following vehicle signals: Vehicle speed
signal, light signal, ignition switch signal, and reverse signal.
History of Errors
Diagnosis results previously stored in the memory (before turning ignition
switch ON) are displayed in this mode. Time and location when/where the
errors occurred are also displayed.
Naviga-
tion
Display Lon-
gitude & Lat-
itude
Display the map. Use the joystick to adjust position. Longitude and latitude
will be displayed.
Speed Cali-
bration
Under ordinary conditions, the navigation system distance measuring
function will automatically compensate for minute decreases in wheel and
tire diameter caused by tire wear or low-pressure. Speed calibration imme-
diately restores system accuracy in cases such as when distance calibra-
tion is needed because of the use of tire chains in inclement weather.
Angle
adjustment
Corrects difference between actual turning angle of a vehicle and turning
angle of the car mark on the display.
Initialize
Location
This mode is for initializing the current location. Use when the vehicle is
transported a long distance on a trailer, etc.
CAN DIAG SUPPORT MONITOR
Display status of CAN communication.
AV-104
NAVIGATION SYSTEM
2006 Pathfinder
Self-Diagnosis Mode (DCU)
EKS00G6Q
OPERATION PROCEDURE
1.
Start the engine.
2.
Turn the audio system off.
3.
While pressing the “PAUSE/MUTE” button, turn the volume con-
trol dial clockwise or counterclockwise for 30 clicks or more.
(When the self-diagnosis mode is started, a short beep will be
heard.)
●
Shifting from current screen to previous screen is performed
by pressing “SCAN” button.
4.
The initial self-diagnosis screen will be shown, and items “Self-
Diagnosis (DCU)”, “Self-Diagnosis (NAVI)”, “Confirmation/
Adjustment” and “CAN DIAG SUPPORT MONITOR” will
become selective.
5.
Perform self-diagnosis by selecting the “Self-diagnosis”.
●
Self-diagnosis subdivision screen will be shown and the oper-
ation enters the self-diagnosis mode.
●
A bar graph shown below the self-diagnosis subdivision
screen indicates progress of the diagnosis.
WKIA3249E
SKIA4207E
SKIA4208E
NAVIGATION SYSTEM
AV-105
C
D
E
F
G
H
I
J
L
M
A
B
AV
2006 Pathfinder
6.
When the self-diagnosis completes, optional part confirmation
screen will be shown.
●
When connection of an optional part is judged error, a screen
to check if the optional part is actually fitted on the vehicle or
not will be shown. When fitted, select the switch of the part on
the screen and press “End”. Then the “SELF DIAGNOSIS”
screen will be shown.
●
When the optional part is connected normally, the switch for
the part will not appear on the screen.
7.
On the “SELF DIAGNOSIS” screen, each unit name will be col-
ored according to the diagnosis result, as follows.
●
If several malfunctions are present in a unit, color of its switch
on the screen will be either red, yellow, or gray, determined by
the malfunction of the highest priority.
8.
Select a switch on the “SELF DIAGNOSIS” screen and com-
ments for the diagnosis results will be shown.
●
When the switch is green, the following comment will be
shown. “Self-diagnosis was successful. Further diagnosis and
adjustments are recommended. Follow the “confirmation/
adjustment” menu or refer to the service manual.”
●
When the switch is yellow, the following comment will be
shown. “Connection to the following unit is abnormal. See the
service manual for further details”.
●
When the switch is red, the following comment will be shown.
“DCU is abnormal”.
SELF–DIAGNOSIS RESULT
Quick reference table
1.
Select a malfunctioning diagnosis No. in the diagnosis result quick reference table.
2.
Find estimated malfunctioning system in the diagnosis No. table and perform check by referring to
3.
Turn the ignition switch OFF and perform self-diagnosis again.
*: DCU = Display control unit
CAUTION:
●
When AV switch has a malfunction, you cannot start. Refer to
AV-147, "Unable to Operate All of AV
Switches (Unable to Start Self-Diagnosis)"
●
When display unit has a malfunction, you cannot start. Refer to
SKIA4209E
Green
: Not malfunctioning.
Yellow
: Cannot be judged by self-diagnosis results.
Red
: Unit is malfunctioning.
Gray
: Diagnosis has not been done.
WKIA1189E
SKIA4211E
Screen switch
Diagnosis No.
Switch color
DCU*
DISPLAY
Audio unit
Navigation
GPS
antenna
Red
×
1
Gray
×
x
2
x
x
3
×
×
×
4
AV-106
NAVIGATION SYSTEM
2006 Pathfinder
Self-Diagnosis Codes
Self-Diagnosis Mode (NAVI)
EKS00G6R
OPERATION PROCEDURE
1.
Start the engine.
2.
Turn the audio system off.
3.
While pressing the “PAUSE/MUTE” button, turn the volume con-
trol dial clockwise or counterclockwise for 30 clicks or more.
(When the self-diagnosis mode is started, a short beep will be
heard.)
●
Shifting from current screen to previous screen is performed
by pressing “SCAN” button.
4.
The initial self-diagnosis screen will be shown, and items “Self-
Diagnosis (DCU)”, “Self-Diagnosis (NAVI)”, “Confirmation/
Adjustment” and “CAN DIAG SUPPORT MONITOR” will
become selective.
Diagnosis
No.
Possible cause
Reference
page
1
Display control unit malfunction
2
Display communication line between display control unit and display unit
3
Audio unit power supply and ground circuit
Audio communication line between display control unit and audio unit
4
NAVI control unit power supply and ground circuit
AV communication line between display control unit and NAVI control unit
WKIA3249E
SKIA4207E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст