Nissan Pathfinder (2006 year). Manual — part 38
REPAIR FOR COMPONENT PARTS
AT-295
D
E
F
G
H
I
J
K
L
M
A
B
AT
2006 Pathfinder
ASSEMBLY
1.
Install seal rings to mid sun gear.
CAUTION:
●
Do not reuse seal rings.
●
Apply petroleum jelly to seal rings.
2.
Install 1st one-way clutch to rear sun gear.
CAUTION:
Apply petroleum jelly to 1st one-way clutch.
3.
Install snap ring to rear sun gear using suitable tool.
4.
Install rear sun gear assembly to mid sun gear assembly.
SCIA2861E
SCIA4633E
SCIA2859E
SCIA2858E
AT-296
REPAIR FOR COMPONENT PARTS
2006 Pathfinder
5.
Install needle bearing to high and low reverse clutch hub.
CAUTION:
Apply petroleum jelly to needle bearing.
6.
Install high and low reverse clutch hub to mid sun gear assem-
bly.
7.
Install snap ring to mid sun gear assembly using suitable tool.
CAUTION:
Do not expand snap ring excessively.
8.
Check operation of 1st one-way clutch.
a.
Hold mid sun gear and turn rear sun gear.
b.
Check 1st one-way clutch for correct locking and unlocking
directions.
CAUTION:
If not as shown, check installation direction of 1st one-way
clutch.
9.
Install needle bearing and bearing race to high and low reverse
clutch hub.
CAUTION:
Apply petroleum jelly to needle bearing and bearing race.
SCIA2857E
SCIA2856E
SCIA2855E
SCIA3132E
SCIA2854E
REPAIR FOR COMPONENT PARTS
AT-297
D
E
F
G
H
I
J
K
L
M
A
B
AT
2006 Pathfinder
High and Low Reverse Clutch
ECS00EM7
COMPONENTS
DISASSEMBLY
1.
Remove bearing race from high and low reverse clutch drum.
2.
Remove snap ring from high and low reverse clutch drum using
suitable tool.
3.
Remove drive plates, driven plates and retaining plate from high
and low reverse clutch drum.
1.
High and low reverse clutch drum
2.
Driven plate
3.
Retaining plate
4.
Snap ring
5.
Drive plate
6.
Bearing race
SCIA5224E
SCIA5215E
SCIA2868E
AT-298
REPAIR FOR COMPONENT PARTS
2006 Pathfinder
INSPECTION
●
Check the following, and replace high and low reverse clutch assembly if necessary.
High and Low Reverse Clutch Snap Ring
●
Check for deformation, fatigue or damage.
High and Low Reverse Clutch Drive Plates
●
Check facing for burns, cracks or damage.
High and Low Reverse Clutch Retaining Plate and Driven Plates
●
Check facing for burns, cracks or damage.
ASSEMBLY
1.
Install drive plates, driven plates and retaining plate in high and low reverse clutch drum.
CAUTION:
Take care with order of plates.
2.
Install snap ring in high and low reverse clutch drum using suit-
able tool.
3.
Install bearing race to high and low reverse clutch drum.
CAUTION:
Apply petroleum jelly to bearing race.
SCIA2868E
SCIA5215E
REPAIR FOR COMPONENT PARTS
AT-299
D
E
F
G
H
I
J
K
L
M
A
B
AT
2006 Pathfinder
Direct Clutch
ECS00EM8
COMPONENTS
DISASSEMBLY
1.
Remove snap ring from direct clutch drum using suitable tool.
2.
Remove drive plates, driven plates and retaining plate from
direct clutch drum.
INSPECTION
●
Check the following, and replace direct clutch assembly if necessary.
Direct Clutch Snap Ring
●
Check for deformation, fatigue or damage.
Direct Clutch Drive Plates
●
Check facing for burns, cracks or damage.
Direct Clutch Retaining Plate and Driven Plates
●
Check facing for burns, cracks or damage.
1.
Direct clutch drum
2.
Driven plate
3.
Retaining plate
4.
Snap ring
5.
Drive plate
SCIA5046E
SCIA2868E
AT-300
REPAIR FOR COMPONENT PARTS
2006 Pathfinder
ASSEMBLY
1.
Install drive plates, driven plates and retaining plate in direct clutch drum.
CAUTION:
Take care with order of plates.
2.
Install snap ring in direct clutch drum using suitable tool.
SCIA2868E
ASSEMBLY
AT-301
D
E
F
G
H
I
J
K
L
M
A
B
AT
2006 Pathfinder
ASSEMBLY
PFP:00000
Assembly (1)
ECS00EM9
1.
Use a drift [commercial service tool: 22 mm (0.87 in) dia.] to
drive manual shaft oil seals into the transmission case until it is
flush as shown.
CAUTION:
●
Apply ATF to manual shaft oil seals.
●
Do not reuse manual shaft oil seals.
2.
Install detent spring and spacer in transmission case and secure
with the bolt.
3.
Install manual shaft to transmission case.
4.
Install parking rod to manual plate.
SCIA5259E
Bolt
: 7.9 N·m (0.81 kg-m, 70 in-lb)
SCIA5248E
SCIA5716E
SCIA5220E
AT-302
ASSEMBLY
2006 Pathfinder
5.
Install manual plate (with parking rod) to manual shaft.
6.
Install retaining pin into the manual plate and manual shaft.
a.
Fit pinhole of the manual plate to pinhole of the manual shaft
with a pin punch.
b.
Use a hammer to tap the retaining pin into the manual plate.
CAUTION:
●
Drive retaining pin to 2
±
0.5 mm (0.08
±
0.020 in) over the
manual plate.
●
Do not reuse retaining pin.
7.
Install retaining pin into the transmission case and manual shaft.
a.
Fit pinhole of the transmission case to pinhole of the manual
shaft with a pin punch.
b.
Use a hammer to tap the retaining pin into the transmission
case.
CAUTION:
●
Drive retaining pin to 5
±
1 mm (0.20
±
0.04 in) over the
transmission case.
●
Do not reuse retaining pin.
8.
Install O-rings to servo assembly.
CAUTION:
●
Do not reuse O-rings.
●
Apply petroleum jelly to O-rings.
9.
Install return spring to servo assembly.
SCIA5715E
SCIA5297E
SCIA2427E
SCIA5719E
SCIA5717E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст