Nissan Pathfinder (2006 year). Manual — part 39
ASSEMBLY
AT-303
D
E
F
G
H
I
J
K
L
M
A
B
AT
2006 Pathfinder
10. Install servo assembly in transmission case.
11. Install snap ring to transmission case using suitable tool.
12. Install D-rings in reverse brake piston.
CAUTION:
●
Do not reuse D-rings.
●
Apply ATF to D-rings.
13. Install reverse brake piston in transmission case.
14. Install needle bearing to drum support edge surface.
CAUTION:
Apply petroleum jelly to needle bearing.
SCIA5679E
SCIA2333E
SCIA6330E
SCIA2325E
SCIA2796E
AT-304
ASSEMBLY
2006 Pathfinder
15. Install seal rings to drum support.
CAUTION:
●
Do not reuse seal rings.
●
Apply petroleum jelly to seal rings.
16. Install spring retainer and return spring in transmission case.
17. Install snap ring in transmission case while compressing return
spring using Tool.
CAUTION:
Securely assemble them using a flat-bladed screwdriver so
that snap ring tension is slightly weak.
18. Install reverse brake drive plates (3), driven plates (4) and dish
plates (5) in transmission case.
●
Snap ring (1)
●
Retaining plate (2)
CAUTION:
Take care with order of plates.
NOTE:
There are 6 drive plates and 6 driven plates.
SCIA3333E
SCIA2324E
Tool number
: KV31102400 (J-34285 and J-34285-87)
SCIA5877E
SCIA6949E
ASSEMBLY
AT-305
D
E
F
G
H
I
J
K
L
M
A
B
AT
2006 Pathfinder
19. Assemble N-spring.
20. Install reverse brake retaining plate in transmission case.
21. Install snap ring in transmission case.
22. Measure clearance between retaining plate and snap ring. If not
within specified clearance, select proper retaining plate.
23. Install needle bearing to transmission case.
CAUTION:
Apply petroleum jelly to needle bearing.
SCIA5249E
SCIA2439E
Specified clearance “A”:
Standard: 0.7 - 1.1mm (0.028 - 0.043 in)
Retaining plate:
.
SCIA3129E
SCIA5031E
AT-306
ASSEMBLY
2006 Pathfinder
24. Install revolution sensor to transmission case and tighten bolt to
specified torque.
CAUTION:
●
Do not subject it to impact by dropping or hitting it.
●
Do not disassemble.
●
Do not allow metal filings, etc. to get on the sensor's front
edge magnetic area.
●
Do not place in an area affected by magnetism.
25. Install return spring (1) to parking pawl (2).
26. Install parking pawl (with return spring) and pawl shaft to rear
extension (2WD models) or adapter case (4WD models).
27. Install parking actuator support to rear extension (2WD models)
or adapter case (4WD models).
28. Install needle bearing (1) to rear extension (2WD models) or
adapter case (4WD models).
CAUTION:
Apply petroleum jelly to needle bearing.
Revolution sensor bolt
: 5.8 N·m (0.59 kg-m, 51 in-lb)
SCIA2320E
SCIA6180J
SCIA3424E
SCIA3423E
SCIA6179J
ASSEMBLY
AT-307
D
E
F
G
H
I
J
K
L
M
A
B
AT
2006 Pathfinder
29. Install seal rings to output shaft.
CAUTION:
●
Do not reuse seal rings.
●
Apply petroleum jelly to seal rings.
30. Install parking gear to output shaft.
31. Install output shaft in transmission case.
CAUTION:
Be careful not to mistake front for rear because both sides
looks similar. (Thinner end is front side.)
32. Install bearing race to output shaft.
33. Install rear extension assembly (2WD models) or adapter case assembly (4WD models) according to the
following procedures.
SCIA5209E
SCIA5247E
SCIA5030E
SCIA5245E
AT-308
ASSEMBLY
2006 Pathfinder
a.
2WD models
i.
Apply recommended sealant (Genuine Anaerobic Liquid Gasket
or equivalent. Refer to
GI-47, "Recommended Chemical Prod-
.) to rear extension assembly as shown in
illustration.
CAUTION:
Completely remove all moisture, oil, old sealant and any
foreign material from the transmission case and rear exten-
sion assembly mating surfaces.
ii.
Install rear extension assembly to transmission case.
CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the rear
extension assembly.
iii.
Tighten rear extension assembly bolts to specified torque.
CAUTION:
Do not reuse self-sealing bolt.
b.
4WD models
i.
Install gasket onto transmission case.
CAUTION:
●
Completely remove all moisture, oil, old gasket and any
foreign material from the transmission case and adapter
case assembly mating surfaces.
●
Do not reuse gasket.
ii.
Install adapter case assembly to transmission case.
CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the rear
extension assembly.
SCIA5212E
SCIA5029E
Rear extension assembly bolt
: 52 N·m (5.3 kg-m,
38 ft-lb)
Self-sealing bolt
: 61 N·m (6.2 kg-m,
45 ft-lb)
SCIA6941E
SCIA5231E
SCIA5186E
ASSEMBLY
AT-309
D
E
F
G
H
I
J
K
L
M
A
B
AT
2006 Pathfinder
iii.
Tighten adapter case assembly bolts (1) to specified torque.
(With terminal bracket (2).)
CAUTION:
Do not reuse self-sealing bolt (3).
34. Install direct clutch assembly in reverse brake.
CAUTION:
Make sure that drum support edge surface and direct clutch
inner boss edge surface come to almost same place.
35. Install needle bearing in drum support.
CAUTION:
Apply petroleum jelly to needle bearing.
36. Install high and low reverse clutch assembly in direct clutch.
Adapter case assembly bolt
: 52 N·m (5.3 kg-m,
38 ft-lb)
Self-sealing bolt
: 61 N·m (6.2 kg-m,
45 ft-lb)
SCIA7220E
SCIA5019E
SCIA5198E
SCIA2306E
AT-310
ASSEMBLY
2006 Pathfinder
37. Align the drive plate using suitable tool.
38. Install high and low reverse clutch hub, mid sun gear assembly
and rear sun gear assembly as a unit.
CAUTION:
Make sure that portion “A” of high and low reverse clutch
drum protrudes approximately 2 mm (0.08 in) beyond por-
tion “B” of rear sun gear.
39. Install needle bearing in rear carrier assembly.
CAUTION:
Apply petroleum jelly to needle bearing.
SCIA3169E
SCIA5018E
SCIA3130E
SCIA2803E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст