Nissan Murano Z51 (2008 year). Manual — part 317
SE-110
< ON-VEHICLE REPAIR >
FRONT SEAT
• Remove the side air bag module harness (A) and disconnect
the seat cushion heater harness connector (B).
3.
Remove the seatback assembly.
• Remove the seatback mounting bolts (A), and then remove
the seatback assembly.
4.
Remove the seat cushion front finisher. (Power seat only)
• Remove the seat cushion front finisher mounting screws (A).
• Remove the seat cushion front finisher mounting pawl.
5.
Remove the seat cushion outer finisher outside.
a.
Power seat
• Remove the seat control switch knob and reclining switch knob and lumbar support switch.
• Remove the seat cushion outer finisher mounting screw (A),
metal clips and pawls.
• Disconnect the seat control switch, reclining switch and lum-
bar support switch harness connectors (Driver's seat only).
b.
Manual seat
JMJIA1426ZZ
JMJIA1427ZZ
: Pawl
JMJIA1428ZZ
: Metal clip
: Pawl
JMJIA1429ZZ
Revision: 2008 October
2009 Murano
FRONT SEAT
SE-111
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
• Remove the pawls, and then lifter lever knob finisher (1).
(Driver's manual seat only)
• Remove the mounting screws, and remove the lifter lever (2).
(Driver's manual seat only)
• Pull out the reclining lever while holding and raising the pawl.
• Remove the mounting screws (A).
• Remove the metal clip and pawls, and then pull out seat cush-
ion outer finisher outside.
6.
Remove the seat cushion outer finisher inside (left).
• Remove the mounting screw (A).
: Pawl
JMJIA1090ZZ
: Pawl
JMJIA1091ZZ
:Metal clip
: Pawl
JMJIA1482ZZ
JMJIA1430ZZ
Revision: 2008 October
2009 Murano
SE-112
< ON-VEHICLE REPAIR >
FRONT SEAT
7.
Remove the seat slide outer cover (Driver's seat only) mounting
screws (A), and then slide to backward.
8.
Remove the mounting screw (A) and pawls, and then pull out
seat cushion inner finisher outer.
9.
Remove the mounting screw (A), and then pull out seat cushion
inner finisher inside (right).
10. Remove the mounting screws (A), and then pull out seat slide
inner cover. (Driver's seat only)
11. Remove the seat cushion trim and seat cushion pad. (Without occupant classification system control unit
model)
• Remove the seat cushion trim retainer.
• Remove the seat cushion trim and seat cushion pad from the seat cushion frame.
• Remove the hog rings, and separate the seat cushion trim and seat cushion pad.
12. Remove the seat belt buckle.
SB-7, "SEAT BELT BUCKLE : Exploded View"
13. Remove the driver seat control unit.
Assembly
Assemble in the reverse order of disassembly.
JMJIA1431ZZ
: Pawl
JMJIA1432ZZ
JMJIA1433ZZ
JMJIA1469ZZ
Revision: 2008 October
2009 Murano
FRONT SEAT
SE-113
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
CAUTION:
Install the hog rings of seat cushion trim in position, and then securely connect the trim or trim cord
with the pad side wire.
Revision: 2008 October
2009 Murano
SE-114
< ON-VEHICLE REPAIR >
REAR SEAT
REAR SEAT
Exploded View
INFOID:0000000003396993
REAR SEAT (LH SIDE)
1.
Headrest (LH)
2.
Headrest holder (locked)
3.
Headrest holder (free)
4.
Seatback trim
5.
Seatback pad
6.
Reclining device inner cover (out-
side)
7.
Reclining device inner cover (inside) 8.
Seat cushion trim
9.
Seat cushion hinge cover
10. Seat cushion link cover
11.
Seat cushion pad and frame
12. Seat cushion link bush
13. Reclining device outer cover
14. Reclining cover
15. Rear seat harness (LH)
JMJIA1466GB
Revision: 2008 October
2009 Murano
REAR SEAT
SE-115
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
REAR SEAT (RH SIDE)
16. Reclining device assembly
17. Seatback control cable
18. Seatback control lever escutcheon
19. Seatback frame
20. Seatback board
21. Seatback board clip
22. Seatback silencer
Refer to
for symbols in the figure.
1.
Headrest (RH)
2.
Headrest (center)
3.
Headrest holder (locked)
4.
Headrest holder (free)
5.
Seatback trim
6.
Seatback pad
7.
Armrest inner cover
8.
Cup holder
9.
Armrest
10. Armrest bush
11.
Armrest outer cover
12. Seat cushion trim
13. Seat cushion hinge cover
14. Seat cushion link cover
15. Seat cushion pad and frame
JMJIA1465GB
Revision: 2008 October
2009 Murano
SE-116
< ON-VEHICLE REPAIR >
REAR SEAT
Removal and Installation
INFOID:0000000003396994
REMOVAL
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
1.
Remove the seat mounting bolts and nuts.
• Pull up the luggage floor finisher front (1).
• Remove the seat mounting bolt (A) and nut (B).
2.
Disconnect the rear seat harness connector (A) and heater unit harness connector (B). (Power return seat
and heater seat model only)
a.
LH side
b.
RH side
3.
Remove the reclining cover.
16. Seat cushion link bush
17. Reclining device inner cover (out-
side)
18. Reclining device inner cover (inside)
19. Reclining device assembly
20. Reclining device outer cover
21. Reclining cover
22. Rear seat harness (RH)
23. Seatback board
24. Seatback board clip
25. Seatback frame
26. Dynamic dumper
27. Seatback control lever escutcheon
28. Seatback control cable
29. Seatback silencer
Refer to
for symbols in the figure.
JMJIA1476ZZ
JMJIA1477ZZ
JMJIA1478ZZ
Revision: 2008 October
2009 Murano
REAR SEAT
SE-117
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
4.
Remove the seatback control cable (1) from reclining device
assembly and seat mounting bolt (A).
5.
Remove the seat cushion hinge cover.
6.
Remove the rear seat mounting bolts (A).
7.
Pull up the seat cushion and remove the seat mounting bolt (A).
8.
Remove the rear seat assembly from back door.
INSTALLATION
NOTE:
Tighten rear seat mouniting bolts and nuts following the numerical order shown in the figure.
1.
Install the rear seat mounting bolt on behind the seatback (out
side) and nut on behind the seatback (inside).
2.
Install the rear seat mounting bolt on the seat cushion out side.
3.
Connect the rear seat harness connector and heater harness connector. (Power return seat and heater
seat only)
JMJIA1479ZZ
JMJIA1480ZZ
JMJIA1481ZZ
JMJIA1683ZZ
Revision: 2008 October
2009 Murano
SE-118
< ON-VEHICLE REPAIR >
REAR SEAT
4.
Install the rear seat mounting bolt on the reclining device exten-
sion bracket.
5.
Install the rear seat mounting bolt and on the seat cushion
hinge.
6.
Connect the seatback control cable.
7.
Install the seat cushion hinge cover.
8.
Install the reclining cover.
CAUTION:
• When removing and installing, use shop cloths to protect parts from damage.
• When removing and installing, 2 workers are required so as to prevent it from dropping.
• Before installation, check that the rear seat harness and seatback control cable is not pressed by
seat frame.
Disassembly and Assembly
INFOID:0000000003396995
SEATBACK
Disassembly
1.
Remove the armrest. (RH seat only)
• Remove the armrest outer cover.
JMJIA1684ZZ
JMJIA1685ZZ
: Pawl
JMJIA1470ZZ
Revision: 2008 October
2009 Murano
REAR SEAT
SE-119
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
• Remove the armrest mounting bolts (A), and then slide the
armrest to toward the arrow direction.
2.
Separate the seatback assembly and seat cushion assembly.
• Disconnect the seat cushion heater unit harness connectors
(A) and remove the harness clamps. (with heater seat model
only)
• Remove the seat cushion link cover.
• Remove the mounting bolt (A), and then separate the seat-
back assembly and seat cushion assembly.
JMJIA1471ZZ
JMJIA1438ZZ
JMJIA1439ZZ
JMJIA1440ZZ
Revision: 2008 October
2009 Murano
SE-120
< ON-VEHICLE REPAIR >
REAR SEAT
3.
Remove the mounting screw (A), and then remove the reclining
device outer cover.
4.
Remove the mounting screws (A), and then remove the reclining
device inner cover (outside). (LH seat)
5.
Remove the seatback trim and pad.
• Remove the clips, and then pull out the seatback board.
• Remove the seatback trim fixing hog rings and retainer.
• Remove the headrest holder.
CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
• Remove the seatback trim and pad from seatback frame.
• Remove the hog rings to separate the seatback trim and seat-
back pad.
6.
Remove the seatback silencer.
JMJIA1441ZZ
JMJIA1442ZZ
: Clip
JMJIA1443ZZ
PIIB4084J
Revision: 2008 October
2009 Murano
REAR SEAT
SE-121
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
7.
Remove the screws (A), and then remove the reclining device
inner cover (outside). (RH seat)
8.
Remove the screw (A), and then remove the reclining device
inner cover (inside).
9.
Remove the mounting bolts (A), and then remove the seatback
frame from reclining device assembly.
10. Remove the mounting nuts (A), and then remove the dynamic
dumper. (With top road sunroof model only)
Assembly
Assemble in the reverse order of disassembly.
CAUTION:
Install the hog rings of seatback trim in position, and then securely connect the trim or trim cord with
the seatback frame.
SEAT CUSHION
Disassembly
1.
Remove the armrest. (RH seat only)
JMJIA1444ZZ
JMJIA1445ZZ
JMJIA1446ZZ
JMJIA1447ZZ
Revision: 2008 October
2009 Murano
SE-122
< ON-VEHICLE REPAIR >
REAR SEAT
• Remove the pawl, and then pull out armrest outer cover.
• Remove the mounting bolts (A), and then slide the armrest to
outside.
2.
Separate the seatback assembly and seat cushion assembly.
• Disconnect the seat cushion heater unit harness connectors
(A) and remove the harness clamps. (with heater seat model
only)
• Remove the seat cushion link cover.
: Pawl
JMJIA1470ZZ
JMJIA1471ZZ
JMJIA1438ZZ
JMJIA1439ZZ
Revision: 2008 October
2009 Murano
REAR SEAT
SE-123
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
• Remove the mounting bolt (A), and then separate the seat-
back assembly and seat cushion assembly.
3.
Remove the seat cushion trim.
Remove the seat cushion trim fixing retainers and hog rings, and then remove the seat cushion trim from
seat cushion pad and frame.
Assembly
Assemble in the reverse order of disassembly.
CAUTION:
Install the hog rings of seat cushion trim in position, and then securely connect the trim or trim cord
with the seat cushion pad wire.
JMJIA1440ZZ
Revision: 2008 October
2009 Murano
SE-124
< ON-VEHICLE REPAIR >
SEATBACK CONTROL CABLE
SEATBACK CONTROL CABLE
Exploded View
INFOID:0000000003639920
REAR SEAT (LH SIDE)
1.
Headrest (LH)
2.
Headrest holder (locked)
3.
Headrest holder (free)
4.
Seatback trim
5.
Seatback pad
6.
Reclining device inner cover (out-
side)
7.
Reclining device inner cover (inside) 8.
Seat cushion trim
9.
Seat cushion hinge cover
10. Seat cushion link cover
11.
Seat cushion pad and frame
12. Seat cushion link bush
13. Reclining device outer cover
14. Reclining cover
15. Rear seat harness (LH)
JMJIA1466GB
Revision: 2008 October
2009 Murano
SEATBACK CONTROL CABLE
SE-125
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
REAR SEAT (RH SIDE)
16. Reclining device assembly
17. Seatback control cable
18. Seatback control lever escutcheon
19. Seatback frame
20. Seatback board
21. Seatback board clip
22. Seatback silencer
Refer to
for symbols in the figure.
1.
Headrest (RH)
2.
Headrest (center)
3.
Headrest holder (locked)
4.
Headrest holder (free)
5.
Seatback trim
6.
Seatback pad
7.
Armrest inner cover
8.
Cup holder
9.
Armrest
10. Armrest bush
11.
Armrest outer cover
12. Seat cushion trim
13. Seat cushion hinge cover
14. Seat cushion link cover
15. Seat cushion pad and frame
JMJIA1465GB
Revision: 2008 October
2009 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст